Table of Contents
Advertisement
Quick Links
'
*( ,QWHUORJL[
*(,QWHUORJL[FRP
Product
Summary
‚qryÃI‚Ã%('"
Installation
The ATP1000 lets you control all programming and operation of compatible security systems
(see the "Specifications" section).
The large 2-line, 16-character display provides easy to read messages to indicate the current sta-
tus of the system. The touchpad includes police, fire, and auxiliary panic buttons that can be acti-
vated anytime. A built-in speaker provides alarm, status, and button-press sounds. A swing-
down door reveals a label with basic system operating commands. The door can be removed by
simply opening it past its stop point. The door can also be reattached later if desired.
Tools and Equipment Needed
•
4-conductor, 22- or 18-gauge wire
•
Screwdriver
•
#6 screws and anchors (included)
•
Panhead screws for gang box installation
•
Saw or utility knife for cutting wallboard
Guidelines
•
Mount the touchpad in an environmentally controlled area (32°F to 120°F/0°C to 49°C).
•
When mounting the touchpad, allow at least 3 inches below it for the swing-down cover.
•
Do not exceed the maximum available power. See the panel installation instructions for max-
imum available power.
•
Table 1 describes the power used by the touchpad.
•
Table 2 describes the maximum wire lengths allowed between the touchpad and the panel.
Table 1: Touchpad Power Usage
Current (mA)
110
Maximum alarm current with the
buzzer sounding and the touchpad
illuminated from a button press
60
Typical operation
12
Power saving mode (no panel AC
power)
Table 2: Maximum Touchpad Wire Lengths
Wire Gauge
Max. Touchpad Wire Length
(Unshielded or
Between Touchpad and Panel
Shielded)
18
750 feet
22
300 feet
$73 7RXFKSDG'LVSOD\
Conditions
,QVWDOODWLRQ ,QVWUXFWLRQV
'RFXPHQW 1XPEHU 5HY $
2FWREHU
1
Advertisement
Table of Contents
Summary of Contents for GE Interlogix ATP1000
- Page 1 'RFXPHQW 1XPEHU 5HY $ 2FWREHU Product The ATP1000 lets you control all programming and operation of compatible security systems (see the “Specifications” section). Summary The large 2-line, 16-character display provides easy to read messages to indicate the current sta- tus of the system.
- Page 2 Attaching the Touchpad to the Mounting Plate Align the tabs at the top of the mounting plate with the slots on the touchpad and swing the touchpad bottom toward the mounting plate. Gently tighten the screw into the bottom of the touchpad. ATP1000 Touchpad/Display Installation Instructions...
- Page 3 1. With the panel powered up, connect the cable to the Programming Touchpad Header (see Fig- ure 4). When using the ATP1000 as a programming touchpad, be careful not to touch its cir- cuit board which is exposed on the backside.
- Page 4 The display shows DA nnn. Press and release the 1 and 2 buttons together repeatedly, until the desired contrast level is displayed. Press ‚ and the display briefly shows DONE, then shows the time and date. ATP1000 Touchpad/Display Installation Instructions...
- Page 5 5. Press ‚ to exit from the configuration mode. Note If the new touchpad unit number was previously learned by the panel, communication between the touchpad and the panel begins immediately. However, if the new touchpad unit number has never been ATP1000 Touchpad/Display Installation Instructions...
- Page 6 Notices FCC Part 15 Information to the User Changes or modifications not expressly approved by GE Interlogix can void the user’s authority to operate the equipment. FCC Part 15 Class B This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
Need help?
Do you have a question about the ATP1000 and is the answer not in the manual?
Questions and answers
Manual de uso
The user manual for the GE Interlogix ATP1000 provides information on installation, power requirements, operating conditions, and troubleshooting for the ATP1000 touchpad. It includes instructions for resetting the system, compatibility details with Concord panels, and specifications such as power requirements (12 VDC nominal), temperature range (32°F to 120°F), and humidity tolerance (95% relative, non-condensing). It also covers UL listings for fire and burglar alarm compliance.
This answer is automatically generated