Kenwood KDC-MP928 Service Manual page 15

QQ
3 7 63 1515 0
• Using the VOL knob, the Sub Woofer Level is to be adjusted
to the following three levels: -15↔0↔+15 . (The default
value: 0)
• Using the VOL knob, the Volume Offset is to be adjusted to
the following two levels: -8↔0. (The default value: 0)
MENU items
• Long-push the [NEXT] key to enter the MENU.
• The [DNPP/SBF] key or [DIRECT] key on the remote con-
troller can also be used to enter the MENU.
• With the remote controller, continuous forwarding is prohib-
ited.
• When a CD is used as a source, the default item will be the
F/W Version. (DXM-6800 mechanism installed models.)
2-ZONE items
• When using sources other than the STANDBY source, us-
ing a short-press on [AUTO] / [TI] key, 2-ZONE ON/OFF is
achieved.
Backup current measurement
When reset in Acc OFF (Back Up ON) condition, MUTE
TE
L 13942296513
terminal goes off after 2 seconds, instead of 15 seconds.
(During this time, the CD mechanism does not function.)
OPEL communication items
During the test mode, OPEL communication line outputs
the following (At every 500msec, the output condition of the
communication line will be switched.)
CE
DATA
CLK
500msec
500msec
500msec
G sensor display items
When source is STANDBY, by short-pressing [ATT] key, the
display is switched to analogy meter display, in which verti-
cal G and horizontal G are displayed.
www
Special display when all lights are on
When all lights are on with the STANDBY source, the fol-
lowing displays are made when the keys shown below are
.
pressed.
TEST MODE
x ao u163
y
i
2 9
8
[1] Version Display
key (Display) C-407WK_S Y S_1.23
(Display) _______ __PA N_1.11
(Display) _________MEM_3.21
[2] Serial number display (8 digits)
key (Display) SNo_XXXXXXXX
[3] Short-press: Power ON time display
key During Power ON time display, by long-pressing [AUD]
key for 2 seconds, the Power ON time will be cleared.
(Display) PonTim_XXXXX
[4] Short-press: CD operation time display.
key During CD operation times display, by long-pressing [AUD]
key for 2 seconds, all CD operation time will be cleared.
(Display) CDTim_0XXXXX
[5] Short-press: CD EJECT number of times display
key During CD EJECT number of times display, by long-
pressing [AUD] key for 2 seconds, CD EJECT number of
times is cleared.
(Display) EjeCnt_XXXXX
[6] Short-press: PANEL open/close number of times display (*1)
Q Q
3 6 7 1 3 1 5
key During PANEL open/close number of times display, by
long-pressing [AUD] key for 2 seconds, PANEL open/
close number of times is cleared.
(Display) PnCnt_XXXXXX
[7] All-light display switching
key White all-light display (or version display, etc.)→Red all-
light→Green all-light→Blue all-light→White all-light→
[FM] ROM correction version display
key (Display) SYS_ROM_R123
(Display) PAN_ROM_R123
When E2PROM is not installed: ROM_ERR_
When un-written: ROM_R – – –
When data is incompatible: ROM_R ∗ ∗ ∗
[ ] AUDIO data default value setting
key (Display) AUDIO_INIT
[ ] Short-press: CD mechanism error log display
key During CD mechanism error log display; by long-pressing
for 2 seconds, all error log information is cleared.
(Display) I2C_
(Display) ERR_1-
co
In " ", "OK" or "NG" is displayed.
In " ", "– –" or an error code is displayed.
.
(*1) One count is made when the panel opens to full or when a disc is
loaded.
KDC-MP928/PSW9531
/PSW9531Y, XXV-01D
9 4 2 8
MAX 65535 (hours)
MAX 65535 (hours)
MAX 65535 (times)
0 5 8 2 9 9 4 2 8
MAX 65535 (times)
m
, 2- , 3-
9 9
9 9
15