Sony hcd-gn1000d Service Manual page 21

QQ
3 7 63 1515 0
1. Track Balance Adjust:
2. Track Gain Adjust:
3. Focus Balance Adjust:
4. Focus Gain Adjust:
5. Eq Boost Adjust:
6. Iop. ED:
7. TRV. Level:
8. S curve(FE) Level:
9. RFL(PI) Level:
0. MIRR Time:
$ 4 Change Value
[RETURN] Return to previous menu
6. Convert data from hexadecimal to decimal using conversion
table.
7. If the remainder is smaller than 93 (decimal), then it is OK.
However, if the value is bigger than 93, then the BU (base unit)
is defective and need to be change.
8. Press
O RETURN
to previous menu.
9. Press [0] button on the remote commander to return to the Top
Menu of Remocon Diagnosis Menu.
TE
L 13942296513
10. Press button to turn off the set.
?/1
[EMERGENCY HISTORY CHECK]
Information of Emergency History.
1. Enter DVD Service Mode.
2. Select "3. Emergency History" by pressing [3] button on the
remote commander. The screen will appear as follows.
Emg. History Check
Laser Hours
1. 01 05 04 04
00 00 00 00
2. 02 02 01 01
00 00 00 00
[Next] Next Page [Prev] Prev Page
[0] Return to Top Menu
www
3. You can check the total time when the laser is turned on during
playback of DVD and CD from the above menu. The maximum
time, which can be displayed are 999h 59min.
.
4. You can check the error code of latest 10 emergency history
from the above menu. To view the previous or next page of
http://www.xiaoyu163.com
Manual Adjust
button on the remote commander to return
CD 999h 59min
DVD 999h 59min
00 92 46 00
00 00 23 45
00 A9 4B 00
00 00 23 45
x ao u163
y
i
http://www.xiaoyu163.com
2 9
8
emergency history, press . or > on the remote
commander. "Error code" consists of the following (a), (b) and
(c).
(a) Error code
Example of Error code
1. 01 05 04 04
00 00 00 00
The meaning off error code is as follows.
01: Communication error (No reply from syscon)
02: Syscon hung up
03: Power OFF request when syscon hung up
19: Thermal shutdown
24: MoveSledHome error
25: Mechanical move error (5 Changer)
26: Mechanical move stack error
30: DC motor adjustment error
31: DPD offset adjustment error
32: TE balance adjustment error
33. TE sensor adjustment error
34. TE loop gain adjustment error
35. FE loop gain adjustment error
36. Bad jitter after adjustment
40. Focus NG
42. Focus layer Jump NG
52. Open kick spindle error
Q Q
3 6 7 1 3 1 5
51: Spindle stop error
60: Focus on error
61: Seek fail error
62: Read Qdata/ID error
70: Lead in data read fail
71: TOC read time out (CD)
80: Can't buffering
81: Unknown media type
(b) Parameter of error code
Example of Error code
1. 01 05 04 04
00 00 00 00
This is the detailed contents of error information
(c) Time of error code
Example of Error code
1. 01 05 04 04
00 00 00 00
This is the laser hours when an error occured.
5. How to clean laser hours
Press
DISPLAY
Both CD and DVD data are cleared.
co
.
HCD-GN1000D
9 4 2 8
00 92 46 00
00 00 23 45
0 5 8 2 9 9 4 2 8
00 92 46 00
00 00 23 45
00 92 46 00
00 00 23 45
m
button and then press [CLEAR] button.
9 9
9 9
21