Advertisement

PETROL GRASS TRIMMER 26cc
EN
RS8020

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the RS8020 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Rockwell RS8020

  • Page 1 PETROL GRASS TRIMMER 26cc RS8020...
  • Page 3: Parts Diagram

    RS8020...
  • Page 4: Assembly

    RS8020 Release button Release button Tighten the clamp knob...
  • Page 5: Filling The Tank

    RS8020 Tighten the clamp knob...
  • Page 6 RS8020 spool pump head knob guard cutoff knife...
  • Page 7 RS8020 0.5-0.7mm protective cover...
  • Page 8 RS8020...
  • Page 9: Component List

    PETROL GRASS TRIMMER 26cc COMPONENT LIST ENGINE AuxILIARy hANdLE CLAMP kNOb SAfETy GuARd CuTTING hEAd / SPOOL IGNITION SwITCh ThROTTLE INTERLOCk ThROTTLE TRIGGER PuLL CORd STARTER fuEL TANk fuEL TANk CAP ChOkE LEvER AIR fILTER COvER PRIMER buLb SPARk PLuG LEAd SOCkET SPANNER fOR SPARk PLuG MuffLER fuEL MIxING bOTTLE...
  • Page 10: Safety Instructions

    PETROL GRASS TRIMMER 26cc ACCESSORIES locked up out of children’s reach. Safety guard 5. Check before use Auxiliary handle Before use always ensure that the tool is not Socket spanner for spark plug damaged, if in doubt contact the helpline. Fuel mixing bottle 6.
  • Page 11 PETROL GRASS TRIMMER 26cc 15. Start and commissioning of the unit qualified person. Contact the helpline for details of a) For units with a clutch, check that the cutting approved service agents. attachments stop turning when the engine is at idles speed.
  • Page 12: Safety Inspection

    PETROL GRASS TRIMMER 26cc SAfETy INSPECTION 7. Do not overreach. Keep proper footing and 1. Look around the engine for signs of oil or petrol. balance at all times. Overreaching can result in Wipe up any spills before starting the engine. loss of balance or exposure to hot surfaces.
  • Page 13: Specifications

    PETROL GRASS TRIMMER 26cc SyMbOLS TEChNICAL dATA Engine displacement: 26cc To reduce the risk of injury, user must read Maximum engine performance instruction manual (in accordance with ISO 8893): 650W Maximum rotational frequency of the spindle: 8000/min Cutting attachment rotational speed at Warning maximum allowed engine speed: 8000/min...
  • Page 14: Mixing Fuel And Oil

    PETROL GRASS TRIMMER 26cc 3. ASSEMbLING ThE GuARd prevent contamination. wARNING! Take great care when assembling 2) Loosen fuel cap slowly to release pressure and to the guard, as there is a very sharp cutting keep fuel from escaping around the cap. edge although it has a blade cover.
  • Page 15: Maintenance

    PETROL GRASS TRIMMER 26cc 4. STOP ThE ENGINE Half position Ignition switch 1) Release throttle trigger 2) Move the Ignition switch to the STOP position. Wait for the cutting-line head to stop before allowing the end of the trimmer to contact anything. 5.
  • Page 16 PETROL GRASS TRIMMER 26cc you begin any maintenance or repairs. Ensure air filter cover. (See Fig. U) Clean the filter in the oil. When filling the filter cover, put the choke lever to the the cutting attachments stop. This will help to middle position.
  • Page 17: Removing A Unit From Storage

    PETROL GRASS TRIMMER 26cc the spool for re-assembly (See Fig. Z). 7. Using a spark plug wrench, remove the spark plug. 6) Insert each end of the cutting lines through the 8. Pour 1 teaspoon of clean 2-cycle oil into the eyelets in the cutting head and locate the spool combustion chamber.
  • Page 18: Troubleshooting

    PETROL GRASS TRIMMER 26cc TROUBLESHOOTING If you experience problems, check the following; Symptom Cause Solution ON/OFF switch STOP. Turn ON/OFF switch I. Choke not OFF(cold engine) Move choke to the OFF position. Add fuel and press priming Out of Fuel. bulb to fill carburetor.
  • Page 20 MAdE IN PRC...

Table of Contents

Save PDF