Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for Jensen Audio JMC-200
- Page 1 MODEL JMC-200 Wall Mountable Micro System USER MANUAL Need technical help. Call 1300 366 144 Mon - Fri, 9 am to 5 pm PLEASE READ THIS USER MANUAL COMPLETELY BEFORE OPERATING THIS UNIT AND RETAIN THIS MANUAL FOR FUTURE REFERENCE.
- Page 2 The serial number of this product is found on its back cover. You should note the serial number of this unit in the space provided as a permanent record of your purchase to aid in identification in the event of theft of loss. Model Number: JMC-200 Serial Number: ____________________...
-
Page 3: Important Safety Instructions
WARNING TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN The lightning flash with arrowhead The exclamation point within an WARNING: TO REDUCE THE symbol, within an equilateral equilateral triangle is intended to RISK OF ELECTRIC SHOCK,... -
Page 4: Class 1 Laser Product
CAUTION CLASS 1 LASER PRODUCT CAUTION CLASS 1 LASER PRODUCT INVISIBLE LASER RADIATION APPAREIL LASER DE CLASSE 1 WHEN OPEN AND INTERLOCKS PRODUCTO LASER DE CLASE 1 DEFEATED. AVOID EXPOSURE TO BEAM This product contains a low power laser device. Follow the advice below for safe operations. -
Page 5: Important Notes
CAUTION: USAGE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. THIS UNIT SHOULD NOT BE ADJUSTED OR REPAIRED BY ANYONE EXCEPT QUALIFIED SERVICE PERSONNEL. SHOULD ANY TROUBLE OCCUR, REMOVE THE POWER SOURCE AND REFER SERVICING TO QUALIFIED PERSONNEL. -
Page 6: Location Of Controls
LOCATION OF CONTROLS 9 10 14 15 1. LINE-IN Jack 13. Play/Pause/ Mem + 2. Speakers 14. Stop/Band 3. Standby/On 15. CD door Open/Close 4. Function (CD/RADIO/AUX) 16. Right Speaker Out Jack 5. Sleep/Alarm Set 17. Left Speaker Out Jack 6. -
Page 7: Button Descriptions
REMOTE CONTROL TRANSMITTER Standby/On 8. Mute 2. Display 9. EQ (Rock/Pop/Jazz/Classic) /Tune DN/Minute 10. Volume + /Memory + /Tune Up/Hour 5. CD Mode/PGM/Clock Adjust 12. Volume - ■ /Band 13. Sleep/Alarm Set 7. Function (CD/RADIO/AUX) 14. Snooze BUTTON DESCRIPTIONS STANDBY/ON PRESS TO SWITCH THE SYSTEM BETWEEN STANDBY AND POWER ON MODE DISPLAY... - Page 8 MODE /PGM /CLK-ADJ IN STANDBY MODE, FOR CLOCK SETTING IN TUNER MODE, FOR PRE-SETTING OF RADIO STATION INTO MEMORY IN CD STOP MODE, FOR PROGRAM FUNCTION AND IN PLAY MODE FOR SELECTING REPEAT 1, REPEAT ALL OR RANDOM FUNCTION ■ /BAND IN CD MODE: PRESS TO TERMINATE CD PLAYBACK IN TUNER MODE: PRESS TO SELECT AM OR FM...
-
Page 9: Power Source
POWER SOURCE This Micro System is designed to operate on AC 240V ~ 50Hz line power. The Remote Control unit operates from 1 “CR2025” Lithium battery (Included). GETTING STARTED ATTACHING THE SPEAKERS NOTE: The right and left speakers are NOT interchangeable. The speaker with RED plug fits only on the right side. -
Page 10: Battery Replacement
The following steps can be accomplished by using either the remote or controls with the same function on JMC-200. For example the current time is set at 12:30 PM. 1. Press the CLK.ADJ Button when the player is in Standby mode. -
Page 11: Radio Tuning
RADIO OPERATION The following procedures can be accomplished by using the remote or controls on the JMC-200. RADIO TUNING Press the Standby/On Button to turn on the unit. Press the FUNCTION Button to operate the unit in the radio mode. -
Page 12: To Receive Preset Stations
4. Press the MODE/PGM/CLK ADJ Button once. The Preset Channel Number “01” with the flashing Preset Indicator, “M”, will appear in the left bottom of the Display. 5. While the Preset Indicator “M” is blinking, press the /MEM+ Button to select the desired preset channel. - Page 13 Press the OPEN/CLOSE Button (15) to open the CD door. Place a CD, with label side frontward, inside the CD compartment and then press the OPEN/CLOSE Button (15) again to close the CD door. After a few seconds, the total number of tracks on the disc and total playing time will appear in the Display and playback of the first track begins.
-
Page 14: Programmed Play
PROGRAMMED PLAY With this function you can program up to 20 titles in the order you desire. 1. In CD Stop mode, press the MODE/PGM/CLK ADJ Button to start programming the tracks. The blinking Program Indicator “PGM”, the Program Channel Indicator “P-01” and the blank Track No. -
Page 15: Using Headphones (Not Included)
AUXILIARY (AUX) OPERATION You can play other music sources (iPod, MP3 player or other digital audio player) through the speakers of this System by connecting the AUX-IN Jack or LINE-IN (RCA) Jack to your external player’s LINE-OUT Jack or Headphone jack. 1. -
Page 16: Alarm Operation
ALARM OPERATION The following steps can be accomplished by using either the remote or controls with the same function on JMC-200. For example the Alarm Time is set at 7:00 AM. SETTING ALARM TIME 1. Press the SLEEP/AL SET button when the player is in standby mode. The Alarm Indicator, “... -
Page 17: Sleep Timer Operation
Button the sleep time decreases by 10 minutes. 2. The unit will automatically turn off after the preset sleep time has elapsed. However, if you want to turn JMC-200 off before the preset sleep time has elapsed, press the Standby/On Button once to switch off the power. -
Page 18: Care And Maintenance
CARE AND MAINTENANCE 1. Avoid operating your unit under direct sunlight or in hot, humid or dusty places. 2. Keep your unit away from heating appliances and sources of electrical noise such as fluorescent lamps or motors. 3. For better Clock Display clarity, avoid operating the unit under direct sunlight or in strong room illumination. -
Page 19: Troubleshooting Guide
TROUBLESHOOTING GUIDE Should you experience difficulties in the use of this player please refer to the following chart or call 1300 366 144 for Product Service and Support. PROBLEM POSSIBLE CAUSE REMEDY The unit is disconnected from Reconnect to the AC outlet. the AC outlet The unit will not play... - Page 20 SERVICE All necessary care is taken at the point of manufacture to ensure this unit will perform to Jensen’s high quality standards. However if this unit becomes faulty within the warranty period please return it to the point of purchase with your proof of purchase for a replacement.
Need help?
Do you have a question about the JMC-200 and is the answer not in the manual?
Questions and answers