Damper Wires - Sony CPD-200GS Service Manual

Displaying the monitor's
information
You can display the model name, serial number and year of
manufacture using the monitor's INFORMATION OSD.
Press and hold the MENU button for 5 seconds.
The INFORMATION OSD appears.
INFORMATION
MENU
MODEL : CPD 100GS
SER NO : 1234567
MANUFACTURED : 1997
The INFORMATION OSD includes the model name, serial
number and manufactured year.
The OSD automatically disappears after about 30 seconds.
Power Saving Function
This monitor has three modes of reduced power
consumption. By sensing the absence of video signal
coming from the computer, it reduces power consumption
as follows.
Power Power Recovery u indicator
consumption consumption time
mode
≤ 120 W
1 Normal — Green
operation (CPD-200GS)
≤ 110 W
(CPD-100GS)
≤ 15 W
2 Approx. Green and orange
Standby
(1st mode) 5 sec. alternate
≤ 15 W
3 Approx. Green and orange
Suspend
(2nd mode) 5 sec. alternate
≤ 8 W
4 Approx. Orange
Active-off
(3rd mode) 5 sec.
5
Power-off 0 W — Off
Note
If no video signal is input to the monitor, the "NO INPUT
SIGNAL" message (page 18) appears. After 30 seconds, the power
saving function automatically puts the monitor into the active-off
mode and the u indicator lights up orange. Once the horizontal
and vertical sync signals are detected, the monitor automatically
resumes its normal operation mode.
Getting Started
Technical Features

Damper Wires

When viewing a white background, very thin horizontal
lines are visible on the screen as shown below. These lines
are damper wires.
The Trinitron tube has a vertically striped aperture grille
inside. The aperture grille allows more light to pass
through to the screen giving the Trinitron CRT more color
and brightness.
These damper wires are attached to the aperture grille to
prevent vibration of the aperture grille and keep the screen
image constantly stable.
Damper wire
Approx. 6cm
(CPD-200GS
only)
Approx. 6cm
Plug & Play
This monitor complies with the DDC™1 and DDC2B
Display Data Channel (DDC) standards of VESA.
When a DDC1 host system is connected, the monitor
synchronizes with the V. CLK in accordance with the VESA
standards and outputs the EDID (Extended Display
Identification Data) to the data line.
When a DDC2B host system is connected, the monitor
automatically switches to the appropriate standard.
DDC™ is a trademark of the Video Electronics Standard
Association.
17
Displaying the monitor's
information
You can display the model name, serial number and year of
manufacture using the monitor's INFORMATION OSD.
Press and hold the MENU button for 5 seconds.
The INFORMATION OSD appears.
MENU
The INFORMATION OSD includes the model name, serial
number and manufactured year.
The OSD automatically disappears after about 30 seconds.
E N
Power Saving Function
F
This monitor has three modes of reduced power
consumption. By sensing the absence of video signal
E S
coming from the computer, it reduces power consumption
as follows.
C
Power Power
consumption consumption
mode
≤ 120 W
1 Normal
operation (CPD-200GS)
≤ 110 W
(CPD-100GS)
≤ 15 W
2
Standby
(1st mode)
≤ 15 W
3
Suspend
(2nd mode)
≤ 8 W
4
Active-off
(3rd mode)
5
Power-off 0 W
Note
If no video signal is input to the monitor, the "NO INPUT
SIGNAL" message (page 18) appears. After 30 seconds, the power
saving function automatically puts the monitor into the active-off
mode and the u indicator lights up orange. Once the horizontal
and vertical sync signals are detected, the monitor automatically
resumes its normal operation mode.
Getting Started
Damper Wires
When viewing a white background, very thin horizontal
lines are visible on the screen as shown below. These lines
are damper wires.
The Trinitron tube has a vertically striped aperture grille
inside. The aperture grille allows more light to pass
through to the screen giving the Trinitron CRT more color
and brightness.
These damper wires are attached to the aperture grille to
prevent vibration of the aperture grille and keep the screen
INFORMATION
image constantly stable.
MODEL : CPD 100GS
SER NO : 1234567
Damper wire
MANUFACTURED : 1997
Plug & Play
This monitor complies with the DDC™1 and DDC2B
Recovery u indicator
Display Data Channel (DDC) standards of VESA.
time
When a DDC1 host system is connected, the monitor
synchronizes with the V. CLK in accordance with the VESA
— Green
standards and outputs the EDID (Extended Display
Identification Data) to the data line.
When a DDC2B host system is connected, the monitor
automatically switches to the appropriate standard.
Approx. Green and orange
5 sec. alternate
DDC™ is a trademark of the Video Electronics Standard
Approx. Green and orange Association.
5 sec. alternate
Approx. Orange
5 sec.
— Off
Technical Features
Approx. 6cm
(CPD-200GS
only)
Approx. 6cm
E N
F
E S
C
17