LORUS NX02 Instruction Manual

NRENX03C
I M
NSTRUCTION
CAL. NX02 (RZ1 SERIES)
CAL. NX03 (RB5 SERIES)
C H A R A C T E R I S T I C S
1. Time/calendar display:
• Analogue display: Hour, minutes and seconds.
• D i g i t a l d i s p l a y : Hour, minutes, seconds,
date and day of the week.
• Fully automatic calendar:
automatically for odd and even months including
February of leap years from the year 1998 to
the end of 2048.
• T i m e i n d i c a t i o n : Changeover between
12- and 24-hour indications is possible.
2 . S t o p w a t c h : Measures up to 23 hours, 59
/100 second increments
minutes and 59 seconds in 1
for the first hour and in 1-second increments
thereafter.
3 . C o u n t d o w n t i m e r : Up to 9 hours and 59
minutes can be set in minute increments.
4 . S i n g l e - t i m e a l a r m : The single-time alarm
can be set to ring only once at the designated
time. As it rings, it is automatically disengaged.
5 . R e g u l a r a l a r m : The regular alarm can be
set to ring on a 24-hour basis.
• H o u r l y t i m e s i g n a l :
every hour on the hour.
6 . D e m o n s t r a t i o n f u n c t i o n : Each mode is
displayed for 2 seconds in order.
7 . Illuminating light: The
the display for easy viewing in the dark.
CROWN/BUTTONS AND DISPLAYS
* The design of the liquid crystal panel differs
depending on the model, though the functions
and method of operation are the same.
Hour hand
Day
B
P M
ma r k
A
Second
hand
Hour Minutes
D a y D a t e
B
Hour
hand
P M 24
1-AL
P M
m a rk
Second A
hand
Hour Seconds
Minutes
The selection of the mode can be made in the
following order with each press of button "A".
05-00
ANUAL
Calendar adjusts
Can be set to ring
light evenly illuminates
Minute hand
D a t e
Hourly time
C
signal mark
C r o w n
A l a r m
m a r k
D
Seconds
M i n u t e
hand
C
Hourly time
signal mark
C r o w n
Alarm mark
D
A
T I M E / C A L E N D A R
m o d e
A
A
R E G U L A R A L A R M
m o d e
By pressing button "C" in the TIME/CALEN-
DAR mode, the SINGLE-TIME ALARM mode is
shown.
C
S I N G L E - T I M E
T I M E / C A L E N D A R
A L A R M m o d e
m o d e
With each press of button "D" in the TIME/
CALENDAR mode, the display changes over in
the following order.
D
T i m e / c a l e n d a r
d i s p l a y
D
B l a n k d i s p l a y
HOW TO SET THE TIME/CALENDAR
• Before setting the analogue time, be sure
to set the digital time.
[ D i g i t a l T i m e / C a l e n d a r S e t t i n g ]
Day
B
PM mark
A
Hour
Minutes
1 . Press button "A" to show the TIME/CALENDAR
mode.
2 . P r e s s b u t t o n " A " f o r 2 t o 3 s e c o n d s t o
s h o w t h e t i m e / c a l e n d a r s e t t i n g d i s p l a y .
A beep sounds for 1 second, and the second
digits start flashing.
3. Selection of the digits to be adjusted (flashing)
is made in the following order by pressing
button "C".
Seconds
→ Minutes →
Hour
1 2 - / 2 4 - h o u r
D a t e
indication
4. Press button "D" to set the flashing digits.
One digit is advanced with each press of
button "D". Digits except seconds and 12-
/24-hour indication move quickly by keeping
button "D" pressed.
5. A f t e r a l l t h e a d j u s t m e n t s a r e c o m p l e t e d ,
p r e s s b u t t o n " A " t o r e t u r n t o t h e T I M E /
C A L E N D A R m o d e . A b e e p s o u n d s f o r 1
s e c o n d .
S e c o n d s s e t t i n g
When the seconds digits are flashing, press
button "D" in accordance with a time signal.
The seconds are reset to "00" and start immediately.
W h e n t h e s e c o n d s c o u n t a n y n u m b e r f r o m
" 3 0 " t o " 5 9 " a n d b u t t o n " D " i s p r e s s e d , o n e
minute is added and the seconds are immediately
reset to "00".
1 2 - / 2 4 - h o u r i n d i c a t i o n s e t t i n g
Changeover between 12- and 24-hour indications
is made alternately with each press of button
"D".
N o t e s :
1 . W h e n s e t t i n g t h e h o u r d i g i t s i n t h e 1 2 -
hour indication, check that AM/PM is properly
s e t . O n l y " P M " m a r k i s d i s p l a y e d a n d
there is no indication for the AM setting.
In the 24-hour indication, "24H" is displayed.
2. Once the year, month and date have been
set, the day of the week is set automatically.
S T O P W A T C H
m o d e
A
T I M E R
m o d e
C a l e n d a r
d i s p l a y
D
D a t e
C
D
Seconds
→ Year
M o n t h