Appliance Data; Installation Requirements; Room Sizing - Smeg P23LIN Installation & User's Instructions

2.0 APPLIANCE DATA

P23 MODELS
Destination
Country
AT, CH, CZ, HR, ES, FI, GB,
GR, IE, IT, NO, SE, SK, TR
DE, PL
BE,FR
NL
L23 MODELS
Destination
Country
AT, CH, CZ, HR, ES, FI, GB,
GR, IE, IT, NO, SE, SK, TR
DE, PL
BE,FR
NL
L30 MODELS
Destination
Country
AT, CH, CZ, HR, ES, FI, GB,
GR, IE, IT, NO, SE, SK, TR
DE, PL
BE,FR
NL
Flow Restrictor Orifice
Oxypilot (Sit/Bray)
Gas Control
Gas Inlet
Ignition
Spark Gap (± 1.0mm)

3.0 INSTALLATION REQUIREMENTS

If the appliance is to be sited near a disused or unserviceable fireplace served by a natural draught flue then the old flue must be
sealed off. It will be necessary to ventilate the old flue to prevent condensation and dampness forming, however any air vent used
to ventilate the old flue must not be sited within 500mm of this appliance. If the flue can be ventilated to the outside of the build-
ing then this is usually the best solution. If in doubt then advice should be sought from a local building control officer. The appliance
is designed to be wall mounted. If the appliance is to be mounted on a newly fabricated area of wall that also serves the purpose of
sealing off the old flue then it is very important that there are no holes, gaps or otherwise in this wall that will allow draughts from
the old flue to enter the room, especially directly behind the appliance. Such draughts could affect the performance of the ODS sys-
tem and result in nuisance cutting out, for example. If the gas supply pipe is to enter the appliance from the rear, i.e. emerge from
the wall behind the appliance, then any hole in the wall from which the pipe emerges must be tightly sealed.

3.1 ROOM SIZING

In the absence of any local Codes and/or Regulations governing room sizing for type A1AS appliances then the information given
here must be followed.
•
P23 and L23 models : The room size should be a minimum of 23m
•
L30 models : The room size should be a minimum of 30m
This is to allow adequate circulation of air and ensure the correct operation of the fire. This volume may include adjacent spaces
but these spaces must not be separated by a door. Note : To calculate a room size in cubic metres (m
in cubic feet (ft ) by 35.3.
3
Inlet Pressure Max Energy Input
(mbar)
Cat
G20 G25
Gross
I 2H
20 -
I 2E
20 -
I 2E+
20 25 2.0/1.85 1.8/1.66 1.0/0.92 0.9/0.83 18.7/23.4 18.6/23.5 4.1/5.3
I 2L
- 25 1.85
Inlet Pressure Max Energy Input
(mbar)
Cat
G20 G25
Gross
I 2H
20 -
I 2E
20 -
I 2E+
20 25 2.0/1.85 1.8/1.66
I 2L
- 25 1.85
Inlet Pressure Max Energy Input
(mbar)
Cat
G20 G25
Gross
I 2H
20 - 2.60
I 2E
20 - 2.60
I 2E+
20 25 2.6/2.4 2.35/2.15 1.5/1.4 1.35/1.25 13.7/16.9 13.6/17.0 4.3/5.6
I 2L
- 25 2.40
P23 MODELS
1.03mm
9114
BM733
Various
Piezo Spark
4.0mm
Min Energy Input
(kW) (kW)
Net Gross Net
2.0 1.8 1.0 0.9
2.0 1.8 1.0 0.9
1.66 0.92 0.83
Min Energy Input
(kW) (kW)
Net Gross Net
2.0 1.8 1.3 1.17
2.0 1.8 1.3 1.17
1.3/1.2 1.17/1.08 18.7/23.4 18.6/23.5 7.4/9.3
1.66 1.2 1.08
Min Energy Input
(kW) (kW)
Net Gross Net
2.35 1.50 1.35
2.35 1.50 1.35
2.15 1.40 1.25
L23 MODELS
1.03mm
9114
BM733
Various
Piezo Spark
4.0mm
(e.g. 3.07m x 3.07m x 2.45m or 10'1" x 10'1" x 8').
3
(e.g. 3.5m x 3.5m x 2.45m or 11'6" x 11'6" x 8').
3
GB-IE-3
GB IE
High Burner Low Burner
Pressure Pressure
(±1.5 mbar) (±0.75 mbar)
Hot Cold Hot Cold
18.7 18.6 4.1
18.7 18.6 4.1
4.0/5.2
23.4 23.5 5.3
High Burner Low Burner
Pressure Pressure
(±1.5 mbar) (±0.75 mbar)
Hot Cold Hot Cold
18.7 18.6 7.4
18.7 18.6 7.4
7.3/9.2
23.4 23.5 9.3
High Burner Low Burner
Pressure Pressure
(±1.5 mbar) (±0.75 mbar)
Hot Cold Hot Cold
13.7 13.6 4.3
13.7 13.6 4.3
4.4/5.5
16.9 17 5.6
L30 MODELS
1.30mm
9114
BM733
Various
Piezo Spark
4.0mm
) divide the room volume
3
2008 Smeg S.p.A.
©
4.0
4.0
5.2
7.3
7.3
9.2
4.4
4.4
5.5