Page 1
CDP-XB720/XB720E 3 7 63 1515 0 SERVICE MANUAL AEP Model CDP-XB720 UK Model CDP-XB720E Photo: CDP-XB720 Model Name Using Similar Mechanism CDP-XE520 CD Mechanism Type CDM14FLS-5BD25 Base Unit Type BU-5BD25 Optical Pick-up Type KSS-213BA/F-NP SPECIFICATIONS L 13942296513 COMPACT DISC PLAYER...
WITH MARK ! ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. – 2 – http://www.xiaoyu163.com...
http://www.xiaoyu163.com SECTION 1 SERVICING NOTE 3 7 63 1515 0 HOW TO OPEN THE DISC TRAY WHEN POWER SWITCH NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK TURNS OFF OR BASE UNIT Insert a tapering driver into the aperture of the unit bottom, and turn The laser diode in the optical pick-up block may suffer in the direction of arrow.
Page 4
http://www.xiaoyu163.com 3 7 63 1515 0 CD-TEXT TEST DISC This unit is able to display the TEXT data (character information) written in the CD on its fluorescent indicator tube. The CD-TEXT TEST DISC (TGCS-313: J-2501-126-A) is used for checking the display. To check, perform the following procedure.
Page 5
http://www.xiaoyu163.com 3 7 63 1515 0 Table 2: CD-TEXT TEST DISC Recorded Contents and Display (In this unit, some special characters cannot be displayed. This is no a fault.) TRACK Recorded contents Display ···· ! ” # $ % & are not displayed ! ”...
http://www.xiaoyu163.com SECTION 3 DISASSEMBLY 3 7 63 1515 0 Note : Follow the disassembly procedure in the numerical order given. 3-1. FRONT PANEL • In order to remove the front panel block when the power supply does not turn on, rotate the cam with tapering driver as the figure shows, and the loading part will be moved.
http://www.xiaoyu163.com SECTION 4 TEST MODE 3 7 63 1515 0 4-1. AF MODE Button No. Button No. Button Button The following checks can be performed in the AF mode, which is Displayed Displayed set by connecting the JW004 (AFADJ) terminal on MAIN LANGUAGE EDIT/ board to the Ground and turning on the power.
Page 9
http://www.xiaoyu163.com 3 7 63 1515 0 4-3. AGING MODE [ MAIN BOARD ] – Component Side – This unit is equipped with an aging mode to check operations of the mechanism deck. • When faults occur: Aging stops, and the state when aging stopped is displayed on the fluorescent display tube.
http://www.xiaoyu163.com SECTION 5 ELECTRICAL BLOCK CHECKING 3 7 63 1515 0 Note: S-curve waveform 1. CD Block is basically designed to operate without adjustment. symmetry Therefore, check each item in order given. 2. Use YEDS-18 disc (3-702-101-01) unless otherwise indicated. 3.
Page 11
http://www.xiaoyu163.com 3 7 63 1515 0 1 track jump waveform Adjustment Location : Center of the waveform [ MAIN BOARD ] – Component Side – A (DC voltage) + 0.7 level : 1.3 Vp-p symmetry – 0.6 JW004 (AFADJ) E-F Balance Check (With general remote commander) JW003 oscilloscope (ADJ)
http://www.xiaoyu163.com SECTION 6 DIAGRAMS 3 7 63 1515 0 6-1. CIRCUIT BOARDS LOCATION POWER board BD board SW board HP board (AEP) DF board MAIN board LOADING board PANEL board L 13942296513 u163 – 12 – http://www.xiaoyu163.com...
Page 13
http://www.xiaoyu163.com 3 7 63 1515 0 THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this, the necessary note is printed in each block.) For schematic diagrams. Note: • All capacitors are in µF unless otherwise noted. pF: µµF 50 WV or less are not indicated except for electrolytics and tantalums.
CDP-XB720/XB720E 3 7 6 3 1 5 1 5 0 6-3. SCHEMATIC DIAGRAM – BD SECTION – • See page 14 for Waveforms. • See page 30 for IC Pin Functions. • See page 34 for IC Block Diagrams.
http://www.xiaoyu163.com 3 7 63 1515 0 6-12. IC PIN FUNCTIONS • IC101 DIGITAL SIGNAL PROCESSOR (CXD2585Q) Pin Name Function Pin No. DVDD – Digital power supply XRST System reset “L” : reset MUTE Muting input “H” : mute DATA Serial data input, supplied from CPU XLAT Latch input, supplied from CPU CLOK...
Page 26
http://www.xiaoyu163.com 3 7 63 1515 0 Pin No. Pin Name Function Tracking error signal input Center servo analog input RF signal input RFDC Test pin (Not used) ADIO – Analog ground AVSS0 Stabilized current input for operational amplifiers IGEN – Analog power supply AVDD0 EFM full swing output...
Page 27
http://www.xiaoyu163.com 3 7 63 1515 0 • IC501 SYSTEM CONTROL (CXP82832-009Q) Pin Name Function Pin No. FL grid signal output FL grid signal output – Connected to VDD – Power supply (+5V) SCOR Sub code sync input 6, 7 – Ground RMIN Remote control signal input...
Page 28
http://www.xiaoyu163.com 3 7 63 1515 0 Pin Name Function Pin No. – Ground – Not used – Connected to ground VDD (+5V) – Power supply (+5V) VFDP (–30V) – Pull down voltage (–30V) XSEL Not used REINIT – Not used LP CONTROL LP control hold output B-MUTE...
Page 30
http://www.xiaoyu163.com 3 7 63 1515 0 IC102 BA6392FP BUFF CH1 OUT F 28 GND BUFF BUFF CH1 OUT R 27 CH4 OUT F LEVEL SHIFT CAPA IN 1 26 CH4 OUT R BUFF CH1 R IN 25 VB IN INTERFACE CH1 F IN 24 VS IN BUFF...
http://www.xiaoyu163.com SECTION 7 EXPLODED VIEWS 3 7 63 1515 0 NOTE: The components identified by • Items marked “*” are not stocked since they are mark ! or dotted line with mark seldom required for routine service. Some delay ! are critical for safety. should be anticipated when ordering these items.
http://www.xiaoyu163.com 3 7 63 1515 0 7-4. BASE UNIT SECTION (BU-5BD25) L 13942296513 M102 M101 The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified. Ref. No. Part No. Description Remark Ref.
http://www.xiaoyu163.com SECTION 8 ELECTRICAL PARTS LIST 3 7 63 1515 0 Note: • SEMICONDUCTORS • Due to standardization, replacements in the parts list The components identified by may be different from the parts specified in the In each case, u: µ , for example: mark ! or dotted line with mark uA...: µ...
Need help?
Do you have a question about the CDP-XB720 and is the answer not in the manual?
Questions and answers