FTX Hooligan RX 4WD Instruction Manual
  1. Manuals
  2. Brands
  3. FTX Manuals
  4. Toy
  5. Hooligan RX 4WD
  6. Instruction manual

FTX Hooligan RX 4WD Instruction Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Hooligan RX 4WD and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for FTX Hooligan RX 4WD

Summary of Contents for FTX Hooligan RX 4WD

  • Page 2: Recommended Tools

    Glow Igniter Items not included but required for use. 12 x AA batteries Fuel Bottle Filter Nitro Fuel Recommended Tools FAST615 Fastrax 7-Piece Tool Set Includes 1.5mm, 2.0mm, 2.5mm, 3.0mm hex wrenches, slotted and phillips screwdriver. FAST625 Cross Wrench Five different hex sizes 7mm, 8mm, 10mm, 12mm &...

  • Page 3: Step 6 Starting The Engine

    Quick Start Guide (images are of FTX  CarnageNT but chasis layout and procedure is identical) STEP 4 Turn on the transmitter and then the receiver. Check to make sure that the servos are operating correctly and that the carburetor closes when the throttle trigger is released.
  • Page 4 2. Then turn the car upside down and pull the pullstarter rapidly until all the excess fuel has emptied onto the floor through the glowplug hole. Make sure you do this outside safely. This process is really only necessary when the engine is cold or brand new and tight.
  • Page 5 Etronix Pulse EX2 Sport 2.4GHZ RADIO SET-UP 2 Channel 2.4GHz Steer Wheel Transmitter 1) INTRODUCTION. 6) TRANSMITTER CHARGING. Thank you for choosing this Etronix Connect a dedicated transmitter charger to the power 2.4GHz radio system, it has been supply. designed for land use but could also Connect the charger to the charging socket on the suit any 2 channel boat.

  • Page 6: Transmitter Functions

    9) TRANSMITTER FUNCTIONS. A vertical aerial achieves maximum range, so the short 2.4GHz aerial (A) can be folded and rotated to achieve the most vertical position once you are holding the handset comfortably. Then it allows you to fold the aerial away for safe storage.

  • Page 7: Receiver Specification

    When at the mid position the model should When pulled back to the handset the model When pushed away the model should brake (and remain stationary, if it creeps slightly adjust should move forwards, if not flick the then move in reverse if applicable) if not simply the throttle neutral dial accordingly.
  • Page 8 12) MATCHING THE RECEIVER TO throttle (channel 2) to a preset position so THE TRANSMITTER. (BINDING) long as power is still supplied to it. Set up the failsafe before first use, by To make sure only one transmitter can control the turning on the transmitter, then supplying receiver they need to be matched, and to do so you power to the receiver.

  • Page 9: Before Starting Your Engine

    IMPORTANT - READ THIS BEFORE STARTING YOUR ENGINE! For your safety - Your engine is not a toy! • You will be working with highly flammable fuel, so keep it away from exposed flames or any thing which might ignite it. Read the safety info on the fuel container.

  • Page 10: Troubleshooting

    stalling, inconsistent performance, and fouling out glow plugs. Don’t give up. Afterwards, energize the glow plug with your glow plug starter These are just a few things you may go through during the break in period. and try to restart the engine in order to burn off any fuel that Just keep it running, apply the throttle on and off as smoothly as you can.
  • Page 11 Pull Starter Hints seconds so try and keep it running by blipping the throttle. Tighten the glowplug while the engine is running if possible. If the engine has stalled The pull starter as fitted to most of the entry level engines is, if restart with the plug tightened.
  • Page 12 Cooling Problems Glossary of Carburettor Functions Engine overheating is most often caused by running the engine too lean or because the cooling air for the cylinder head is blocked. If the mixture is Main Needle Valve (High Speed) too lean, simply allow the engine to cool, richen the mixture and try it again. The main needle mixture screw controls how much fuel enters the engine Bodies must have holes cut in them to allow for cooling air to circulate over during mid- to high-speed operation.

  • Page 13: Common Parts List

    COMMON PARTS LIST...
  • Page 14 COMMON PARTS LIST...
  • Page 15 PARTS LIST...
  • Page 16 PARTS LIST...
  • Page 17 PARTS LIST...
  • Page 18 PARTS LIST...
  • Page 19 PARTS LIST...
  • Page 20 PARTS LIST...

  • Page 21: Upgrade Parts List

    UPGRADE PARTS LIST...
  • Page 22 NOTES...
  • Page 23 NOTES...

Table of Contents