Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Operating Manual
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Biamp Vocia VO-4
Summary of Contents for Biamp Vocia VO-4
- Page 1 Vocia ® VO-4 Operation Manual Biamp Systems, 10074 S.W. Arctic Drive, Beaverton, Oregon 97005 U.S.A. (503) 641-7287 www.biamp.com...
-
Page 2: Table Of Contents
table Of cOntents VOcia Output 4 (VO-4) features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . frOnt panel . -
Page 3: Vocia Output 4 (Vo-4) Features
Rotary switches for unit identification • Power Over Ethernet (PoE) • CobraNet audio/control with dynamic use of available bundles, plus power over single Ethernet cable • Status LEDs to indicate signal and clip • marked and RoHS compliant • Covered by BiAmP Systems’ warranty... -
Page 4: Front Panel
VO-4 frOnt panel Setup and Use The Vocia software provides an intuitive interface for configuration, DSP equalization, and programming of the VO-4. The information supplied by this manual relates to physical connections and assignment. For more details on software setup, please consult the Vocia Help File. Power/ Network Output 4... -
Page 5: Rear Panel Controls
VO-4 rear panel cOntrOls BIAMP SYSTEMS Designed in Australia N24138 Assembled in USA Model VO-4 YEL:in use/conductor GRN:link/act Control Outputs Control Inputs Audio Outputs Device ID CobraNet ® C NC NO C NC NO C NC NO C NC NO 3 4 10V PoE IEEE 802.3af... - Page 6 If other network traffic shares an Ethernet switch with the Vocia network, a managed switch should be used with separate VLANs. All Ethernet wiring is to be done using shielded CAT5, CAT5e, CAT6, or CAT7 cable. VO-4 BIAMP SYSTEMS Designed in Australia N24138...
-
Page 7: Control Outputs
VO-4 rear panel cOntrOls Control Outputs The Control Outputs, labeled 1 through 4, are isolated, voltage-free, software-configurable relay outputs. The individual pins are labeled as follows: 1. (C): the common/ground pin 2. (NC): normally closed (connected to C when relay is not energized) 3. -
Page 8: Installation
VO-4 installatiOn Installation The VO-4 requires one 1.75 inches (44.45mm) high and 19 inches (483mm) wide rack space with 10 inches (254mm) depth. mounting the unit using four screws with washers will prevent marring of the front panel. PVC or nylon washers are appropriate. Please install the unit away from heat sources, such as vents and radiators, and in rooms with adequate ventilation. -
Page 9: Specifications & Block Diagram
VO-4 specificatiOns Vocia Output 4 SPECIFICATIONS 20Hz to 20kHz + or – 1dB Frequency Response: Control Outputs Type: Form C Voltage free change over contact Max Operating Voltage: 125VAC, 60VDC THD + N (20Hz to 8kHz): <0.02% Max Switching Capacity: 37VA Min Operating Load: 10µA @ 10mV DC... -
Page 10: Warranty
9. BIAMP Systems shall not be liable for special, indirect, incidental, or consequential damages, including lost profits or loss of use arising out of the purchase, sale, or use of the products, even if BiAmP Systems was advised of the possibility of such damages. - Page 11 cOMpliance...
- Page 12 cOMpliance...
Need help?
Do you have a question about the Vocia VO-4 and is the answer not in the manual?
Questions and answers