ZEP DURASHOT S Instructions Manual

SURE SHOT
MODEL M MODEL M
DURA SHOT S
24 oz.
MODEL M
DIRECTIONS FOR OPERATING MODEL "M" SPRAYERS DIRECTIONS FOR OPERATING MODEL "M" SPRAYERS
1) ALWAYS DEPRESSURIZE SPRAYER BEFORE 1) ALWAYS DEPRESSURIZE SPRAYER BEFORE
1) ALWAYS DEPRESSURIZE SPRAYER BEFORE
REMOVING ANY PARTS. The pressure may be let REMOVING ANY PARTS. The pressure may be let
REMOVING ANY PARTS. The pressure may be let
DIRECTIONS FOR OPERATING MODEL "M" SPRAYERS
out of the sprayer one of the two following ways: out of the sprayer one of the two following ways:
out of the sprayer one of the two following ways:
a) Tip the sprayer upside down and depress the a) Tip the sprayer upside down and depress the
a) Tip the sprayer upside down and depress the
a) Always use the entire product in sprayer before
1) ALWAYS DEPRESSURIZE SPRAYER BEFORE
trigger until no pressure is left. If some liquid
trigger until no pressure is left. If some liquid trigger until no pressure is left. If some liquid
you refill as this will make sure you will have 24
REMOVING ANY PARTS. The pressure may be let
is left in the sprayer when you attempt this
is left in the sprayer when you attempt this is left in the sprayer when you attempt this
oz. on your next fill.
out of the sprayer one of the two following ways:
procedure make sure you aim the nozzle at a
procedure make sure you aim the nozzle at a procedure make sure you aim the nozzle at a
place where a little bit of liquid can be expelled.
b) place where a little bit of liquid can be expelled. place where a little bit of liquid can be expelled.
a) Tip the sprayer upside down and depress the
b) Remove #122 black cap from air filler and use
trigger until no pressure is left. If some liquid
b) Remove #122 black cap from air filler and use b) Remove #122 black cap from air filler and use
small probe to depress #121 valve core until
is left in the sprayer when you attempt this
small probe to depress #121 valve core until small probe to depress #121 valve core until all the pressure escapes. NOTE: Make sure
procedure make sure you aim the nozzle at a
all the pressure escapes. NOTE: Make sure all the pressure escapes. NOTE: Make sure
the sprayer is upright and the air filler stem is
place where a little bit of liquid can be expelled.
pointing away from you when depressing the
the sprayer is upright and the air filler stem is the sprayer is upright and the air filler stem is
valve core.
c)
pointing away from you when depressing the pointing away from you when depressing the
b) Remove #122 black cap from air filler and use
valve core. valve core.
small probe to depress #121 valve core until
c) Remove the complete top assembly from the
all the pressure escapes. NOTE: Make sure
canister once all the air has been let out. Do
c) Remove the complete top assembly from the c) Remove the complete top assembly from the
this by grasping the body in one hand and the
the sprayer is upright and the air filler stem is
canister once all the air has been let out. Do canister once all the air has been let out. Do
canister in the other while unscrewing
pointing away from you when depressing the
this by grasping the body in one hand and the this by grasping the body in one hand and the
counterclockwise completely.
valve core.
canister in the other while unscrewing canister in the other while unscrewing
2) Fill sprayer 2/3 full (24 ounce maximum liquid
2) Connect the sprayer to the quick connect on the
counterclockwise completely. counterclockwise completely.
c) Remove the complete top assembly from the
capacity) with light, clean liquid. Make sure the liquid
machine (Pictured below). Push the joystick to the
canister once all the air has been let out. Do
2) Fill sprayer 2/3 full (24 ounce maximum liquid 2) Fill sprayer 2/3 full (24 ounce maximum liquid you are putting into the sprayer is CLEAN and FREE
RIGHT (liquid side) of the machine until the yellow
this by grasping the body in one hand and the
OF FOREIGN PARTICLES. See ACCESSORIES on
capacity) with light, clean liquid. Make sure the liquid capacity) with light, clean liquid. Make sure the liquid
cap on the rod moves all the way to the right
canister in the other while unscrewing
page 3 for liquid filling/measuring device.
you are putting into the sprayer is CLEAN and FREE you are putting into the sprayer is CLEAN and FREE
(approx. 15 seconds) and stops.
counterclockwise completely.
OF FOREIGN PARTICLES. See ACCESSORIES on OF FOREIGN PARTICLES. See ACCESSORIES on
2) Fill sprayer 2/3 full (24 ounce maximum liquid
page 3 for liquid filling/measuring device. page 3 for liquid filling/measuring device.
capacity) with light, clean liquid. Make sure the liquid
ALWAYS DEPRESSURIZE THE SPRAYER BEFORE REMOVING ANY PARTS
you are putting into the sprayer is CLEAN and FREE
OF FOREIGN PARTICLES. See ACCESSORIES on
page 3 for liquid filling/measuring device.
ALWAYS DEPRESSURIZE THE SPRAYER BEFORE REMOVING ANY PARTS ALWAYS DEPRESSURIZE THE SPRAYER BEFORE REMOVING ANY PARTS
ALWAYS DEPRESSURIZE THE SPRAYER BEFORE REMOVING ANY PARTS
SURE SHOT
INSTRUCTIONS INSTRUCTIONS
DURA SHOT
INSTRUCTIONS
Refillable, reusable. Extra versatile. Refillable, reusable. Extra versatile.
INSTRUCTIONS
Pressurized by free air Pressurized by free air
Refillable, reusable. Extra versatile.
Pressurized by free air
Refillable, reusable. Extra versatile.
Pressurized by free air
24 OZ. 24 OZ.
MODEL M
24 OZ.
24 OZ.
DIRECTIONS FOR OPERATING MODEL "M" SPRAYERS
SPRAYER NOT RECOMMENDED FOR USE WITH PAINTS
MAXIMUM PRESSURE 200 PSI
SPRAYER NOT RECOMMENDED FOR USE WITH PAINTS SPRAYER NOT RECOMMENDED FOR USE WITH PAINTS
MAXIMUM PRESSURE 200 PSI MAXIMUM PRESSURE 200 PSI
SPRAYER NOT RECOMMENDED FOR USE WITH PAINTS
MAXIMUM PRESSURE 200 PSI
SPRAYERS
®
SPRAYERS
® S SPRAYERS
™
DIRECTIONS FOR OPERATING
DURA SHOT
™
NOTE: ALWAYS CHECK WITH YOUR CHEMICAL NOTE: ALWAYS CHECK WITH YOUR CHEMICAL
NOTE: ALWAYS CHECK WITH YOUR CHEMICAL
SUPPLIER IF YOU ARE NOT SURE OF COMPATIBILITY. SUPPLIER IF YOU ARE NOT SURE OF COMPATIBILITY.
SUPPLIER IF YOU ARE NOT SURE OF COMPATIBILITY.
READ CAUTION LABEL ON SPRAYER BEFORE FILLING. READ CAUTION LABEL ON SPRAYER BEFORE FILLING.
READ CAUTION LABEL ON SPRAYER BEFORE FILLING.
NEVER USE ACIDS IN ANY NEVER USE ACIDS IN ANY
NEVER USE ACIDS IN ANY
DURA SHOT
SURE SHOT SPRAYER. SURE SHOT SPRAYER. SURE SHOT SPRAYER.
NOTE: ALWAYS CHECK WITH YOUR CHEMICAL
SUPPLIER IF YOU ARE NOT SURE OF COMPATIBILITY.
READ CAUTION LABEL ON SPRAYER BEFORE FILLING.
3) Take the complete top assembly and screw it
3) Take the complete top assembly and screw it 3) Take the complete top assembly and screw it
NEVER USE ACIDS IN ANY
3) Release the control lever; make sure it returns to
clockwise into top of the canister. Firmly hand
clockwise into top of the canister. Firmly hand clockwise into top of the canister. Firmly hand
tighten only.
center for several seconds, then push lever to the
SURE SHOT SPRAYER.
tighten only. tighten only.
LEFT for air, and hold for approx. 15 seconds. This
4) Charge sprayer with compressed air by holding
4) Charge sprayer with compressed air by holding 4) Charge sprayer with compressed air by holding
will fill the sprayer with up to 125 P.S.I. of air and
standard air chuck on valve stem of the air filler.
3) Take the complete top assembly and screw it
siphon the chemical back into the pump so you are
standard air chuck on valve stem of the air filler. standard air chuck on valve stem of the air filler.
Hold the air chuck on the air filler until you hear the
clockwise into top of the canister. Firmly hand
line pressure equalize with the sprayer. Working ready for the next fill. (If you do not hold the lever to
Hold the air chuck on the air filler until you hear the Hold the air chuck on the air filler until you hear the
tighten only.
pressure is 80-150 psi. At least 80 psi is needed to
the left long enough the rod will retract slightly
line pressure equalize with the sprayer. Working line pressure equalize with the sprayer. Working
spray the full 24 oz. without a recharge of air.
4) Charge sprayer with compressed air by holding pressure is 80-150 psi. At least 80 psi is needed to indicating a short fill. Push the lever back to the left pressure is 80-150 psi. At least 80 psi is needed to
THE MAXIMUM PRESSURE SHOULD NOT
for an additional 5 seconds and release.)
spray the full 24 oz. without a recharge of air. spray the full 24 oz. without a recharge of air.
standard air chuck on valve stem of the air filler.
EXCEED 200 PSI.
THE MAXIMUM PRESSURE SHOULD NOT THE MAXIMUM PRESSURE SHOULD NOT
Hold the air chuck on the air filler until you hear the
4) Disconnect the quick connect from top of sprayer by
5) The Model "M" sprayer is now ready to use. EXCEED 200 PSI. EXCEED 200 PSI.
line pressure equalize with the sprayer. Working
pulling the outside collar of the quick connect until it
pressure is 80-150 psi. At least 80 psi is needed to
6) For best results, the liquid to be sprayed should be
releases. You are ready to spray.
5) The Model "M" sprayer is now ready to use. 5) The Model "M" sprayer is now ready to use. The DURA SHOT sprayer is now ready to use.
spray the full 24 oz. without a recharge of air.
lighter than a No. 10 motor oil. (If liquid is too heavy
THE MAXIMUM PRESSURE SHOULD NOT
6) For best results, the liquid to be sprayed should be 6) For best results, the liquid to be sprayed should be
a pin stream will result). DILUTE WITH A SUITABLE
EXCEED 200 PSI.
DILUENT UNTIL DESIRED SPRAY IS OBTAINED.
lighter than a No. 10 motor oil. (If liquid is too heavy lighter than a No. 10 motor oil. (If liquid is too heavy
a pin stream will result). DILUTE WITH A SUITABLE a pin stream will result). DILUTE WITH A SUITABLE
CAUTION: Never point the nozzle of sprayer toward
5) The Model "M" sprayer is now ready to use.
DILUENT UNTIL DESIRED SPRAY IS OBTAINED. DILUENT UNTIL DESIRED SPRAY IS OBTAINED.
yourself or another person. Always point the nozzle
6) For best results, the liquid to be sprayed should be
of the sprayer away from yourself and toward your
CAUTION: Never point the nozzle of sprayer toward CAUTION: Never point the nozzle of sprayer toward
intended target before depressing the trigger.
lighter than a No. 10 motor oil. (If liquid is too heavy
yourself or another person. Always point the nozzle yourself or another person. Always point the nozzle
a pin stream will result). DILUTE WITH A SUITABLE
of the sprayer away from yourself and toward your of the sprayer away from yourself and toward your
CAUTION: Never point the nozzle of sprayer toward yourself
DILUENT UNTIL DESIRED SPRAY IS OBTAINED.
intended target before depressing the trigger. intended target before depressing the trigger.
or another person. Always point the nozzle of
CAUTION: Never point the nozzle of sprayer toward
the sprayer away from yourself and toward your
yourself or another person. Always point the nozzle
intended target before depressing the trigger.
of the sprayer away from yourself and toward your
intended target before depressing the trigger.
ALWAYS DEPRESSURIZE THE SPRAYER BEFORE
REMOVING ANY PARTS.
SPRAYER NOT RECOMMENDED FOR USE WITH PAINTS.
MAXIMUM PRESSURE 200 PSI.
S SPRAYERS
S SPRAYER.
™