Advertisement
Table of Contents
- 1 Table of Contents
- 2 Water Softener Gallon Setting Chart
- 3 System Specifications
- 4 Programming
- 5 General System Installation
- 6 System Configuration
- 7 Maintenance
- 8 Power Head Valve Exploded View
- 9 Power Head Parts List
- 10 Control Valve Exploded View
- 11 Control Valve Parts List
- 12 Trouble Shooting
- Download this manual
Advertisement
Table of Contents
Summary of Contents for AQUATECH CAN165-75
- Page 1 165 Series Softener Operation Manual Note: 1. Read all instructions carefully before operation. 2. Avoid pinched o-rings during installation by applying (provided with install kit) NSF certified lubricant to all seals. Rev 12, December 28, 2011...
-
Page 2: Table Of Contents
TABLE OF CONTENTS Water Softener Gallon Setting Chart ..................2 System Specifications......................3 Introduction ..........................4 Programming .......................... 5 General System Installation ....................7 Start-up Instructions ....................... 7 System Configuration ......................8 Maintenance ........................... 9 Power Head Valve Exploded View ..................11 Power Head Parts List ...................... -
Page 3: Water Softener Gallon Setting Chart
Water Softener Gallon Setting Chart Water Softener Gallon Setting Chart Instructions: First select the chart for your model of water softener, then simply line up the number of people living in the home with the hardness of the water and select the appropriate gallon setting for your model. at 6lbs salt/CF .75 CF Total Hardness in Grains per US Gallon... -
Page 4: System Specifications
System Specifications Figure 2.Specifications Maximum Water Temperature = 110°F (43°C) At the stated service flow rates, the pressure drop through these devices will not exceed 15 psig. Maximum Operating Pressure = 100 PSIG (689 kPa) Changing salt settings from factory setting may require ... -
Page 5: Programming
Programming 1. Press ‘ ’ to enter programming. If the system has been inactive, you may have to hold and press ‘ ’ until you hear a beep to unlock the display screen. Press ‘ ’ or ‘ ’ to select which setting to modify. 2. - Page 6 Program Options Depending on the current option settings, some parameters cannot be viewed or set. Program Mode DESCRIPTION PARAMETER OPTIONS This option controls whether cubic meters or US gallons is used for the volume display and the format REGIONAL METRIC of the day, year, and month.
-
Page 7: General System Installation
General System Installation Water Pressure Minimum 25 PSI Electrical Supply Uninterrupted 115V AC Existing Plumbing Free of any deposits or build-ups inside pipes. Softener Location Locate close to drain and connect according to plumbing codes Bypass Valves Always provide for bypass valve if unit is not equipped with one. - Page 8 3. Any solder joints near the valve must be done before connecting any piping to the valve. Always leave at least 6" (152 mm) between the valve and joints when soldering pipes that are connected to the valve. Failure to do this could cause damage to the valve.
-
Page 9: System Configuration
System Configuration SYSTEM CAPACITY (GRAINS) CYCLE TIME (MINUTES) REFILL TIME (MINUTES) @ 0.70 GPM BLFC RESIN VOLUME @ 6 lbs/cu ft @ 6 lbs/cu ft @ 15 lbs/cu ft @ 10 lbs/cu ft @ 3 lbs/cu ft @ 15 lbs/cu ft @ 10 lbs/cu ft @ 3 lbs/cu ft BACKWASH BRINE/RINSE RINSE... -
Page 10: Maintenance
Maintenance Adding Salt Use only crystal water softener salt. Check the salt level monthly. It is important to maintain the salt level above the water level. To add salt, simply lift the salt lid and add the salt directly into the brine tank. Be sure the brine well cover is on and fill only to the height of the brine well. -
Page 11: Power Head Valve Exploded View
Power Head Exploded View See parts listing on next page (12) -
Page 12: Power Head Parts List
Power Head Parts List Item No. Part No. Part Description Quantity 5056136 Screw-ST3.5×13(Hexagon with Washer) 5056014 Bnt65 Back Cover 5010045 Piston Stem Holder 13000426 Screw-ST2.9×13(Large Wafer) 5056139 Washer-3x13 5056005 Main Gear 5056083 Screw-M4x14 5056166 Screw-ST4.2×12(Large Wafer) 5056141 Washer-4x12 13111004 Washer-4x9 5056016 Refill Regulator 5056015... -
Page 13: Control Valve Exploded View
Control Valve Exploded View See parts listing on next page (14) -
Page 14: Control Valve Parts List
Control Valve Parts List I t em N o. P art N o. P art D i scri pt i on Q uant i t y A 01 05056087 S crew -M 5× 12(H exagon) A 02 05056088 S crew -M 5× 16(H exagon w i t h W asher) A 03 05056047 E nd P l ug R et ai ner... -
Page 15: Trouble Shooting
Trouble Shooting Issue Possible Cause Possible Solution A. Unit fails to initiate a 1. No power supply. Check electrical service, fuse, etc. regeneration cycle. 2. Defective circuit board. Replace faulty parts. 3. Power failure. Reset time of day. B. Water is hard. 1. - Page 16 Manufacturers Warranty Canature North America Inc. warrants that your new water conditioner is built of quality material and workmanship. When properly installed and maintained, it will give years of trouble free service. Five Year Complete Parts Warranty: Canature North America Inc. will replace any part which fails within 60 months from date of manufacture, as indicated by the serial number, provided the failure is due to a defect in material or workmanship.
Need help?
Do you have a question about the CAN165-75 and is the answer not in the manual?
Questions and answers