Advertisement

Quick Links

PlusConnect™ GatesAir ZXA
Installation and Operation Manual
PlusConnect™ GatesAir ZXA Manual REV B

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PlusConnect GatesAir ZXA and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Burk PlusConnect GatesAir ZXA

  • Page 1 PlusConnect™ GatesAir ZXA Installation and Operation Manual PlusConnect™ GatesAir ZXA Manual REV B...
  • Page 2: Table Of Contents

    Setting up Labels, Limits and Alarms ...................... 8 Creating a PlusConnect Custom View in AutoPilot Plus ................8 Operation ............................... 9 Troubleshooting ........................... 10 Connection Errors ..........................10 Getting Help ............................10 Warranty ............................... 11 Copyright © 2015 Burk Technology, Inc.
  • Page 3: Introduction

    ARC Plus before adding the PlusConnect to the system. Installation Note Even though you may operate the ARC Plus and PlusConnect on different subnets, Burk Technology strongly recommends installing the PlusConnect on the same LAN as the ARC Plus. In a network failure, an ARC Plus can only continue to monitor and control a PlusConnect on the same LAN.
  • Page 4: Compatibility

    Compatibility Transmitter Compatibility The PlusConnect GatesAir ZXA is compatible with the GatesAir ZXA Transmitter models (20RU) ZX500, ZX1000, ZX2000 and ZX3500. New models (ZX2500, ZX3250, ZX5000, ZX7.5 AND ZX10 are covered in a separate manual, PlusConnect GatesAir ZXB. Transmitter models, firmware versions and options are subject to change. Visit www.burk.com for current information.
  • Page 5: Front Panel Indicators

    On or Off and turn on Telnet Client.) 5. When prompted, enter the default password for the PlusConnect: password. Burk Technology PlusConnect Harris ZX16 v1.0.6 Password: 6. Telnet will display the main menu. PlusConnect™ GatesAir ZXA Installation and Operation Manual...
  • Page 6 To change a setting, enter the menu number for that setting and the press <Enter>. PlusConnect™ GatesAir ZXA Installation and Operation Manual...
  • Page 7: Additional Snmp Parameters

    7. Enter the appropriate configuration settings for the following parameters: Setting Description IP Address The IP address you want to assign to the PlusConnect unit Subnet The subnet mask for your LAN Gateway The gateway for your LAN Transmitter IP Address The IP address of your GatesAir ZXA series transmitter Transmitter SNMP Port Normally 161...
  • Page 8: Installation

    Now that the PlusConnect is installed on the network and connected to the transmitter, you are ready to add the PlusConnect to the ARC Plus using AutoLoad Plus. AutoLoad Plus is included with the ARC Plus, and may also be downloaded from www.burk.com. Configuration involves: ...
  • Page 9: Manually Mapping Plusconnect Parameters

    4. AutoLoad Plus will prompt you to select the device type. Select “PlusConnect GatesAir ZXA”. You may optionally change the description for the PlusConnect. The description appears in AutoLoad Plus to identify each PlusConnect channel. 5. Enter the IP address and port number of the PlusConnect. These should be the same settings you used when you configured the PlusConnect using telnet.
  • Page 10: Setting Up Labels, Limits And Alarms

    Mapping additional channels is accomplished in AutoLoad Plus by selecting the Meter Channels, Status Channels or Commands tab, as appropriate: 1. Within any of these tabs, click the Override button to change a channel’s assignment from a traditional I/O channel to a Plus-X channel. 2.
  • Page 11: Operation

    2. When the Custom View Editor opens, select File  New From Template… This opens the Load Template dialog. 3. Browse for the desired template. The default location for templates is %ProgramFiles%\Burk Technology\AutoPilot 2010\Templates\Custom Views. Choose the PlusConnect Load Template dialog folder, followed by GatesAir ZX Series.
  • Page 12: Troubleshooting

    ARC Plus front panel and from AutoPilot. Getting Help For customer support, please email support@burk.com or call our direct customer support line at 978- 486-3711. We will be glad to assist you. The customer support office is open Monday – Friday, 9AM to 5PM Eastern Time.
  • Page 13: Warranty

    Damage in shipping is not the responsibility of Burk Technology. A return authorization must be obtained before returning any equipment. Materials returned under this warranty must be shipped freight prepaid and insured in the original shipping carton or suitable substitute to Burk Technology, Inc., 7 Beaver Brook Road, Littleton, MA 01460.

Table of Contents