Summary of Contents for JCM Technologies Free30r
- Page 1 Free hands free system for vehicles and people Applications manual for Free system jcmtechnologies be a step ahead with technology and imagination...
- Page 2 jcmtechnologies be a step ahead with technology and imagination...
-
Page 3: Table Of Contents
Free hands free system for vehicles and people Introduction. Description of the system. Requirements of the normative. Functioning. Installation. Installation and conections Trigger Free 15R, Free 30R and Free 50R/RS. Installation Tag Free T. Programming. Tag Programming in the Receiver. Trigger Programming. -
Page 4: Introduction
FreeTH is a multi-use product, especially designed for controlling the movements of the people, lo- cating people in buildings, presence control, emergency and evacuation plans, etc., in companies, offices, banks, sports centres, hospitals and geriatric centres, among others. Free30r Free50rs Free50r... -
Page 5: System Description
Free applications manual for Free system Introduction System description FreeT (TAG) Nominal range: 100 meters. Transmission frequency: 868 MHz. Power: 1 x 3Vdc batteries type CR2032. Batteries last for approximately 2 years. Acoustic operating indicator for low battery, signal transmission and programming. Push-button inlet for voluntary activations. - Page 6 Pre-wired connection. Operating temperature -20°C a + 55°C. ABS IP66 plastic case. Size of Free30r: 205 x 183 x 14 mm. Size of Free15r: 87 x 78 x 15 mm. Stand alone (no connections between Free antennas and other devices)
-
Page 7: Requirements Of The Normative
The instructions for use of this equipment must always remain in the possession of the user. JCM TECHNOLOGIES, S.A. declares herewith that the products FreeT, FreeTH, Free15r, Free30r, Free50r, Free50rs, comply with the requirements of the 1999/5/CEE R&TTE Directive, 2004/108/EC Directive on electromagnetic compatibility and 2006/95/EC on low voltage, insofar as the product is used correctly. -
Page 8: Functioning
Free applications manual for Free system Functionning Hands Free functionning Free system works as hands free. While entering with FreeT/TH device in the activation area of the Free50r or Free50rs trigger, it activates itself sending a radio signal to the receiver. To activate the Tag once inside the activation area, or to get out of it, you could always press the push button of FreeT if it is needed at any time. - Page 9 Free applications manual for Free system Functionning FreeT tag also works though a push button in difference from FreeTH. In this very case, the fuctionning is manual. Manual functionning While pressing the button, tag works exactly the same as a traditional transmitter. It only sends the TAG code plus Open Group (Group 0 by default) and channel 1.
-
Page 10: Installation
To a better adjustment of the activation area, Free30r is supplied together with an orientable wall support. This support is also compatible with Free15r, but in this very case, it must be acquired as accessory. - Page 11 Collective Installation In a collective installation of Free15r / Free30r, these must be connected in series and four units as maximum can be connec- ted. To ensure a perfect functionning of these triggers, the OUT sincronism signal must be connected to the following IN one, and once we arrive to the last trigger, we have to link the IN signal of this last one to the OUT signal of the first one.
- Page 12 Free applications manual for Free system Installation TAG FreeT Installation FreeT ofers to the user a very simple and comfortable way of installation, either vehicle, clothe or as keyholder. To install it in the vehicle, there is a car holder. It must be sticked to the car by removing the sticker protection. We recommend to stick it in a plane surface.
- Page 13 Free applications manual for Free system Programación Programming TAG in receivers TAG can be programmed in the receiver manually or by using the programming tool Assistant or PROG-MAN. Manual Programming To program or learn the FreeT in a receiver, the programming function in the receiver must be activated by the Prog button. Once the receiver has emit one whistle, that means programming is open, the push button of the Tag must be pressed or also canbe aproach the Tag to a trigger in order to make the Tag to activate itself.
-
Page 14: Programming
Free applications manual for Free system Programming Trigger programming The trigger allaows to program Codes and Groups. Both are done thanks to the push button and following the color indications given by the led. Channels: 4 channels maximum To start to program the channels of the trigger, the push button of it must be pressed. Then the led will start blinking slowly and showing a red color. -
Page 15: Applications
Free applications manual for Free system Applications FreeT has been though to be used in applications such residential, community, shopping, offices, restaurants, industry, institu- tions and twon planning. FreeTH has been though to be used in hospitals, offices, restaurants and industries. Application in shops and hospitality Application in offices Application in Industry... - Page 16 Free applications manual for Free system Applications Application in barriers Application in residential and community doors jcmtechnologies be a step ahead with technology and imagination...
-
Page 17: Recommendations
Free applications manual for Free system Recommendations To ensure an optimal functionning of the Free System, from JCM we do recommend to follow the below advises • Do not install the trigger in metallic surfaces. If so, the range can be affected. •... - Page 18 Free applications manual for Free system Receivers allowed for the groups Resume of receivers which can work with FREE system GROUPS RECEIVERS MOTION JCM Compatible with Applications Description Receiver GROUPS system 1 impulse relay channel. / 2 channel (Relay 1 impulse and relay 2 selectable impulse/bi-stable).
- Page 19 Free applications manual for Free system Receivers allowed for just one group Resume of receivers which can work with just one FREE system GROUP. RECEIVERS MOTION JCM Compatible with Applications Description Receiver GROUPS system 2 canales (relé 1 impulsional, relé 2 impulsional/bies- 868 MHz radio table modificables con herramienta de programación receiver.
- Page 20 tech tecnología & imaginación...