Summary of Contents for JETT BTM-D1D
-
Page 1: Table Of Contents
Table of Content Table of Content BTM-D1D Wireless Body Temperature Monitor User Manual Introduction of BTM-D1D – Wireless Body Temperature Monitor Operating Instructions The Instructions of Indicators Importance Precautions Q & A Technical Specifications ... - Page 2 BTM-D1D Wireless Body Temperature Monitor User Manual BTM-D1D includes: • ReceiverX 1 • Armband X 1 • AAA battery X 2 • 3 Volt lithium cell battery (CR2032) X 1 • Arm-belt X 1 • Assisted arm belt X 1 •...
-
Page 3: Introduction Of Btm-D1D Wireless Body Temperature Monitor
Introduction of BTM-D1D Wireless Body Temperature Monitor (1) The instruction of the keys and functions: LCD Screen Beeper LO Setting Key HI Setting Key & AAA batteres X 2 ℃/℉ Switch Temperature Setting Power Key Power Indicator • Power key: To turn on/off the Receiver. - Page 4 (2)The LCD screen of the Receiver illustration: Armpit Temperature Mode ℃ / ℉ Temperature Indicator High / Low Temperature Alarm Armband Battery Wireless Transmdission Indicator Indicator Receiver Battery Indicator (3) The armband: Back side Front side Power Indicator Temperature Sensor Power Key CR2032 Battery Battery Installation:...
- Page 5 Note: 1. This product is made by FDA Grade Silicone. Clean the surface of armband with wet tissue. Do not immerse the armband into water. 2. Recommend to use CR2032 battery manufactured within 2 month. If use poor quality or years-old CR2032 battery, it may easy to become powerless when power-on which means the battery can not supply power normally.
-
Page 6: Operating Instructions
Operating Instructions (1) How to use the armpit temperature function: POWER ON Step 1: Wear the armband on the left arm and adjust the belt at the proper tightness. Move the temperature sensor under the armpit. Step 2: Press the “Power key” on the armband for 2 seconds until the green light flash and it will flash every 4 seconds to indicate the device is working. - Page 7 2. If outside of signal area and then result in disconnection, please remove the receiver close to the armband within 3 min and then the signal will be connected. 3. Any abnormal occurred when turn on the armband, please check and change the battery.
- Page 8 after finishing high temperature setting. Please press “Temperature Setting Key” when “LO” is flashing, and then adjust the low temperature setting. The temperature standard is 0.5℃ a time such as 34℃ to 34.5℃ then 35℃ then 35.5℃ and so on and then press “Temperature setting key”...
- Page 9 (3) Check the Hi/Lo temperature alarm setting: The Hi/Lo setting (4) The Abnormal temperature alarm: Alarm: The Hi/Lo temperature alarm setting on the LCD screen will be flashing on the “Hi” or “Lo” if the reading of the patient is out of the temperature alarm setting range.
- Page 10 keep noticing the caregiver to take appropriate action via the constant beeps if the patient’s temperature is out of the temperature alarm setting. Press any key on the Receiver to stop the beep alarm. Remark: ‧ Please keep checking the patient’s temperature when alerting, even some action to the patient had been done.
-
Page 11: The Instructions Of Indicators
The Instructions of Indicators (1) Armband Power Indicator: Light Status Flashing Green Power On Every 4 seconds Power Off One blink then power off Orange Low Volt Every 4 seconds when power on No Signal Every 10 seconds when power on (2) Battery Power Supply Alarm The Low Battery Alarm of Receiver: Power Supply... - Page 12 Please turn on again the Receiver and the Armband to re-set signal transmission. Status Temperature Indicator Alarm Siren Poor signal Beeps twice every10 seconds — — —℃ “Beep, Beep” “Beep, Beep”….. (4) Solution for Poor Signal: Within 3 minutes if disconnection occurred, please remove the Receiver close to the armband while waiting for the screen in monitoring mode.
-
Page 13: Importance Precautions
Importance Precautions 1. Please follow the manual to operate this product carefully. 2. This product is designed to put the armband on the left arm. 3. This product is designed to function properly under the conditions of the surrounding temperature between 15℃ to 40℃, and the relative humidity of 95% or lower. -
Page 14: Q & A
Q & A Q: The armpit temperature monitored is much higher or lower than normal? Please check the possible situation as follows: 1. The patient may have a fever or the temperature may be too low. 2. The Temperature Sensor does not reach the armpit or the armband is not tight enough. - Page 15 Q: Cannot turn on the Receiver? 1. Please read carefully the manual again. 2. Check the battery well to make sure batteries are in it, or please change new batteries. 3. Batteries may be not installed correctly. 4. This product may be out of order, please call to customer center. Q: The armband power indicator flashing with green and red light? 1.
-
Page 16: Technical Specifications
Technical Specifications Receiver Armband One 3 Volt lithium cell battery (CR2032). Up to 72-96 hours Two AAA batteries of constant operation. Power supply Up to 80-100 hours of *If under airwave interference constant operation environment, the battery life will be shortened. Dimensions(mm) 130H X 50W X 32D 136H X 85W X 9.5D...