Summary of Contents for Emcore 10901G
-
Page 1: Power Supply
Operator's Manual System 10000 Power Supply Model 10901G MAN-10901G Rev B 2015 Chestnut Street Alhambra, California 91803 (626) 293-3400 Fax: (626) 293-3428 www.emcore.com... - Page 2 Every attempt has been made to make this material complete, accurate, and up-to-date. Users are cautioned, however, that Emcore Corporation, reserves the right to make changes without notice and shall not be responsible for any damages, including consequential, caused by reliance on the material presented, including, but not limited to, typographical, arithmetical, or listing errors.
- Page 3 Emcore Corporation assumes no liability for the customer's failure to comply with these precautions. Calls attention to a procedure or practice, which if ignored, may result in damage to the system or system component.
- Page 4 30 days of receipt of the shipment, or within 30 days of discovery of a defect within the warranty period. This warranty is the only warranty made by Emcore Corporation and is in lieu of all other warranties, expressed or implied, except as to title, and can be amended only by a written instrument signed by an officer of Emcore Corporation.
- Page 5 Customer approval for the repair and any associated costs will be the authority to begin the repair at Emcore Corporation. Customer approval is also necessary for any removal of certain parts, such as connectors, which may be necessary for Emcore Corporation testing or repair.
-
Page 6: Table Of Contents
Emcore Corporation MAN-10901G Rev B 10901G Operating Manual Power Supply Table of Contents Chapter 1 GENERAL DESCRIPTION Introduction ..................................1-1 System Applications................................1-1 System Description ................................1-1 System Specifications................................. 1-2 Chapter 2 INSTALLATION AND SETUP PROCEDURES Introduction ..................................2-1 Unpacking and Inspecting the System..........................2-1 Installing System Assemblies.............................. -
Page 7: Chapter 1 General Description
The information applies to all 10901G models. System Applications This plug-in power supply for the Emcore Corporation System 10000 supplies 60 Watts total power to drive up to eight 7.5 Watt Emcore Corporation plug-in units. -
Page 8: System Specifications
Emcore Corporation MAN-10901G Rev B 10901G Operating Manual Power Supply System Specifications 10901G Power supply Output Voltage Tol. Load Max. Ripple and Noise Line Regulation Load Regulation +0.2V +5.3V 120 mV p-p 0.4% -0.1V +0.2V +15.2V 150 mV p-p 0.4% -0.4V... -
Page 9: Chapter 2 Installation And Setup Procedures Introduction
Power Supply Chapter 2 INSTALLATION AND SETUP PROCEDURES Introduction This section contains information and procedures for installing the Model 10901G Power Supply, and for preparing it for operation. Unpacking and Inspecting the System Unpack the system carefully; thoroughly inspecting the equipment to assure that no damage has occurred in shipment. If damage is found, notify the responsible carrier and Emcore Corporation immediately. -
Page 10: Chapter 3 Operation Procedures
Emcore Corporation MAN-10901G Rev B 10901G Operating Manual Power Supply Chapter 3 OPERATION PROCEDURES Introduction The system normally operates without operator intervention. Periodic checking of LED voltage indicators will help keep the system running without interruption. During normal operation, it is recommended to check the system every six hours. - Page 11 Emcore Corporation MAN-10901G Rev B 10901G Operating Manual Power Supply 1 0 9 0 1 G Model 10990A Chassis, Main Power Supply Status Connector (P11 – P18)) Pin - Chassis Pin - Connector Description See individual unit manua See individual unit manua...
-
Page 12: Chapter 4 Maintenance And Troubleshooting Introduction
Emcore Corporation MAN-10901G Rev B 10901G Operating Manual Power Supply Model 10990A Chassis Power Supply Status Connector (P19) Description PS 1 OFF PS 1 ON PS 2. OFF PS 2. ON Chassis Connector connection connection PS 2. Status closed open... -
Page 13: Routine Maintenance Procedures
System failure or degradation is normally indicated by system indicators, monitors and alarms. Note: Contact Emcore Corporation to return apparently failed plug-ins for repair. Plug-ins must be repaired only by qualified, factory-trained personnel. Refer to Installation and Setup Procedures for information and procedures for measuring signal levels and performance.