Summary of Contents for Moser Baer Max CAAP
- Page 1 Installation and User Manual Moser Baer Photo Voltaic Modules Crystalline Silicon Modules Max/Value - Series Re-energizing the World!
- Page 2 Moser Baer is a world leader in development and high-volume- manufacturing of technology products. Our prime commitment is to produce quality products that last for many years. Moser Baer PV modules are designed for versatility in application and suited for residential, commercial and industrial applications.
- Page 3 Installation and User Manual Moser Baer Photo Voltaic Modules Crystalline Silicon Modules Max Series - " CAAP " Value Series - "AHFP", "BAAP", "BCAP", "BDAP", "BGFP”...
-
Page 4: Table Of Contents
Index Installation and User manual Moser Baer Max/value Series Photovoltaic Modules Contents Warning Notice General safety Handling safety Installation safety Mechanical Installation Site Selection Tilt Angle Selection Mounting Installation 2.3.1 General Installation 2.3.2 Ground Mounting 2.3.3 Roof mounting 2.3.4 Pole mounting... -
Page 5: Warning Notice
1 WARNING NOTICE Hazardous electricity ! Can shock burn or cause death. 1.1 General Safety Photovoltaic modules can generate electricity upon exposure to light. The voltage of a single module is less than 45VDC, but the shock hazard increases as modules are connected in parallel producing higher current. -
Page 6: Installation Safety
avoid the hazard of electric shock or injury. When carrying a module, two or more people should carry it by its frame and wear non-slip gloves (to avoid injury by a slipping module, to a foot, or cuts by the edge of a frame, and so on). -
Page 7: Mechanical Installation
12. Do not change the connection of bypass diodes to avoid the hazard of electric shock and injury. 13. Max/Value - Series of modules qualified for Application class A 2 MECHANICAL INSTALLATION 2.1 Site Selection: PV modules are intended for outdoor use only and should be installed in a location where they will receive maximum sunlight throughout the year. -
Page 8: Mounting Installation
Sun Arc Table: Latitude 10° 15° 20° 25° 30° 35° 40° 45° Summer 12.71° 13.02° 13.34° 13.7° 14.08° 14.54° 15.02° 16.62° Winter 11.54° 11.24° 10.92° 10.58° 10.21° 9.80° 9.33° 8.76° 2.3 Mounting Installation: General Installation Place the modules on top of the structure & mount it by using the pre-drilled elliptical mounting holes as shown below &... -
Page 10: Ground Mounting
The support module mounting structure must be made of durable , corrosion resistant and UV resistant material. Modules should be firmly fixed in place in a manner suitable to withstand all expected loads, including wind & snow loads. Determine wind loads for the installation site &... -
Page 11: Roof Mounting
In addition ensure that the lowest portion of the module is placed high enough so that it is not shaded by trees or plants and not damaged by sand or stone driven by wind. The supporting frame/structure is used to mount modules at correct tilt angles. Clearance between the modules frame &... -
Page 12: Pole Mounting
Additional devices such as ground fault, fuses, and disconnects may be required. Make sure that roof structure can support the installation load and might require service of professional installers. The modules should never be sealed to the mounting surface with sealant that prevents the junction box from touching the surface &... -
Page 13: Grounding Method
The DC electrical energy from a PV module may be also be converted to AC and connected to a utility grid system. As local policies on connecting renewable energy systems to a grid may vary from region to region, please consult a qualified system designer or integrator to design such a system. -
Page 14: General Installation
Option 1 Option 2 The grounding will be provided by fixing Attach all module to an earth ground using earthing cable with Hex Nut, Star Tooth the 'Solklip' ground clip (manufactured by Washer, Flat Washer and Hex Head Bolt as TYCO). - Page 15 (Type USE-2, rated 90°Cwet or dry, 1000V 12AWG 4mm double insulated, halogen free UV resistant solar cables Resistance to UV, water, ozone, fluids, salt and against general weathering, Resistance to abrasion. 1. Conductor: Standard tin plated copper No./Dia 56x0.30mm Dia. of conductor: ø 2.56mm Electron beam cross-linked polyolefin, colour: Natural 2.
- Page 16 11. Blocking Diodes ;Blocking diodes can prevent night time battery discharging and also prevent modules from loss of array output and damage by reverse current flow. Moser Baer PV modules do not contain blocking diodes when shipped from the factory however most battery charge regulators do have this feature.
-
Page 17: Maintenance
Note: STC : Irradiance 1000 W/m , cell Temperature at 25°C & AM 1.5 spectrum - Module available in each category are within ± 10% power range. - Refer product data sheet of particular category of module on Moser Baer web site for detailed information. - Page 18 Typical Electrical Parameters Unit MBPV CAAP Nominal Power at STC, Pmax ±3% Power tolerance at STC (min / max) Voltage at Pmax , Vmp 26.95 27.53 27.94 28.47 28.81 28.90 29.12 29.21 29.42 29.80 30.12 30.59 30.80 Current at Pmax, Imp 6.68 6.72 6.85...
-
Page 19: Product Identification
PV modules as per this manual. No responsibility is assumed by Moser Baer Photo voltaic for any infringement of patents or other rights of third parties that may result from use of PV modules. No license is granted by implication or under any patent or patent rights. - Page 20 Manufactured by: Re-energizing the World!
Need help?
Do you have a question about the Max CAAP and is the answer not in the manual?
Questions and answers