Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Iembeddedpc PEB-7605 Series
- Page 1 PEB-7605 Series Socket 478 / 479 Pentium M / Celeron M Mini ITX Main Board User’s Manual P/N: PEB-7605 Version 1.0, July 28,2006 Copyright© Jun., 2002. All rights reserved All other brand names are registered trademarks of their respective owners.
-
Page 2: Table Of Contents
PEB-7605 Series User’s Manual Table of Contents How to Use This Manual .....................4 Chapter 1 Introduction ....................4 1.1 Packing Check List ..................4 1.2 Product Specification................... 5 1.3 System Architecture..................6 Chapter 2 Hardware Configuration Setting............. 7 2.1 Jumpers ......................7 2.2 Connectors .................... - Page 3 PEB-7605 Series User’s Manual 4.13 Load Fail-Safe Defaults................35 4.14 Load Optimized Defaults................35 4.15 Save & Exit Setup..................36 ２...
-
Page 4: How To Use This Manual
PEB-7605 Series User’s Manual How to Use This Manual This manual is written for the system integrator, PC technician and knowledgeable PC end user. It describes how to configure your PEB-7605 to meet various operating requirements. The user’s manual is divided into four chapters, with each chapter addressing a basic concept and operation of the server board. -
Page 5: Chapter 1 Introduction
1.1 Also provide dual display function by VGA and LVDS interface.. The Mini-ITX standard makes the PEB-7605 SERIES work with the one slot PCI . One 6-pin Mini-DIN connectors are provided to connect PS/2 mouse and keyboard. The on-board Flash ROM is used to make the BIOS update easier. -
Page 6: Product Specification
PEB-7605 Series User’s Manual 1.2 Product Specification ◇ Support Intel Pentium Mobile / Celeron M processor up to 2.1GHz and above or Celeron M processor 800MHz / 1GHz on board ◇ CPU bus clock : 400 MHz Chipset Intel® 82852GM GMCH & 82801DB ICH4 Main Memory ◇... -
Page 7: System Architecture
◇ Operating Temperature : 0 ~ 60 ℃ ◇ Storage Temperature : -20~70℃ ◇ Relative Humidity : 5% to 95%, non-condensing 1.3 System Architecture All of details operating relations are shown in (Figure 1-1) PEB-7605 SERIES System Block Diagram. Figure 1-1 PEB-7605 SERIES System Block Diagram ６... -
Page 8: Chapter 2 Hardware Configuration Setting
(SHORT) or remove (NC) it from the jumper pins according to the following instructions. Here, NC stands for “Not Connect”. 2.2 Connectors I/O peripheral devices will be connected to the interface connectors in (Figure 2-2) PEB-7605 SERIES Connector Locations. ７... -
Page 9: Rtc Cmos Clear Jumper (Qn5)
PEB-7605 Series User’s Manual Figure 2-2 PEB-7605 SERIES Connector Locations CONNECTOR FUNCTION REMARK RTC CMOS Clear 1x3 shrouded header PANEL1 1-3 IDE active indicator 1x2 shrouded header PANEL1 2-4 System Power On LED 1x2 shrouded header PANEL1 6-8 System Power on Switch... -
Page 10: Atx_20P2P Power Connector(Pwr1)
PEB-7605 Series User’s Manual 2.2.5 ATX_20P Power Connector (PWR1) Signal Description PIN No. +3.3V +3.3V Ground Ground Ground PW_OK +5V SB +12V +3.3V -12V Ground PS ON Ground Ground Ground 2.2.6 COM1/COM2/COM3/COM4 Interface PIN No. Signal Description Data Carrier Detect... -
Page 11: Parallel Port Interface
PEB-7605 Series User’s Manual 2.2.8 Parallel Port pin header Interface Signal Signal Description Description STB# SCK# BUSY SLCT AFD# ERR# INIT# SLIN# 2.2.9 External USB3 (USB2.0) This motherboard provides one USB headers on the board allowing for 2 additional USB ports. To make use of this header, you must attach a USB bracket/cable with USB ports (some models will come packaged with a USB 2-port bracket-cable). -
Page 12: Usb & Lan Connector : Usb1/2/3/4 / Lan 1&2
PEB-7605 Series User’s Manual 2.2.10 USB & LAN Connectors: USB/ b LAN 1&2 This motherboard comes with 4 USB ports and two LAN ports. The USB connectors are used to attach to keyboards, mice and other USB devices. You can plug the USB devices directly into this connector. The LAN connectors can be attached directly to a network. -
Page 13: Cpu_Fan / Sys_Fan
PEB-7605 Series User’s Manual 2.2.14 CPU_FAN / SYS_FAN PIN No. Signal Description Ground +12V RPM signal 2.2.15 PS/2 Keyboard & Mouse(KBMS1) PIN No. Signal Description Keyboard Data Mouse Data Ground Keyboard Clock Mouse Clock 2.2.16 VGA D-SUB15 Connector PIN No. -
Page 14: Inverter Pwr Connector
PEB-7605 Series User’s Manual 2.2.19 LCD Inverter Power voltage Connector PIN No. Signal Description VCC12M1 VCC5V VCC12M1 LCD inverter power voltage LVDS_BKLTEN 2.2.20 Compact Flash Connector PIN No. Signal Description PIN No. Signal Description HD03 HD04 HD05 HD06 HD07 CS0#... -
Page 15: Chapter 3 System Installation
PEB-7605 Series User’s Manual Chapter 3 System Installation This chapter provides you with instructions on how to setup your system. The additional information shows you how to install CPU/ FAN and memory . 3.1 Socket 478 / 479 Processor 3.1.1 Installing Pentium M / Celeron M Processor The processor socket comes with a screw to secure the processor, please unlock the screw first. -
Page 16: Main Memory
NOTE: For maintaining system stability, do not change any of DDR memory parameters in BIOS setup to upgrade your system performance without acquiring technical information. 3.2 Installing the Mini ITX To install your PEB-7605 SERIES into standard chassis or proprietary environment, you need to perform the following steps: (1). Check all jumpers setting on proper position (2). -
Page 17: Dual Realtek 81Xx Ethernet Controller
3.2.2 Dual Realtek 81xx 10/100 Base-TX Ethernet controller Dual Realtek 81xx 10/100 BASE-TX Ethernet controller by PCI . The PEB-7605 SERIES provides two LED indicators on RJ-45 connector to show LAN interface status. These messages will give you a guide for troubleshooting. -
Page 18: Drivers Support
PEB-7605 Series User’s Manual 3.2.3 Drivers Support PEB-7605 SERIES provides on CD-Title to support on-board VGA and Ethernet device drivers in various operating systems. Before installing the device drivers, please see the reference files in each sub-directory. You cannot install drivers from CD-Title directly. -
Page 19: Chapter 4 Bios Setup Information
PEB-7605 Series User’s Manual Chapter 4 BIOS Settings 4.1 Entering Setup Phoenix-Award BIOS has a built-in setup program that allows users to modify the basic system configuration. This information is stored in CMOS RAM whose power is supplied by a battery so that it can retain the setup information even when the power is turned off. -
Page 20: Standard Cmos Features
PEB-7605 Series User’s Manual 4.3 Standard CMOS Features Date (mm/date/year) and Time (hh/mm/ss) Allow you to change the date and time of the system clock. No matter how good the quality of the motherboard, remember that losing (or gaining) several seconds per month is not a surprising thing. -
Page 21: Total Memory
PEB-7605 Series User’s Manual Total Memory Displays the total memory available in the system. 4.4 Advanced BIOS Features 4.4.1 CPU Feature... -
Page 22: Thermal Management
PEB-7605 Series User’s Manual Thermal Management This BIOS feature controls the activation of the Thermal Monitor＇s automatic mode. It allows you to determine when the Pentium 4＇s Thermal Monitor should be activated in automatic mode after the system boots. In general, the Thermal Monitor should not be activated immediately on booting since the processor will be under a heavy load during the booting process, which results in the sharp rise in die temperature from its cold state, which leads to the unstable system. -
Page 23: Advanced Chipset Features
PEB-7605 Series User’s Manual MPS Version Control for OS The 1.1 version is the older version that supports 8 more IRQs in the Windows NT environment. Choose the new 1.4 version for Windows 2000 and Windows XP. Options: 1.4 (default)、1.1 OS Select For DRAM >... -
Page 24: System Bios Cacheable
PEB-7605 Series User’s Manual CAS latency time. DRAM RAS# to CAS# Delay This item allows you to select a delay time between the CAS and RAS strobe signals. It only applies when DRAM is written to, read from, or refreshed. This field is adjustable only when “DRAM Timing Selectable” is set to “manual”. This field is locked when “DRAM Timing Selectable”... -
Page 25: Integrated Peripherals
PEB-7605 Series User’s Manual 4.6 Integrated Peripherals 4.6.1 OnChip IDE Device... -
Page 26: Onboard Device
PEB-7605 Series User’s Manual On-Chip channel 0/channel 1 PCI IDE The motherboard chipset contains a PCI IDE interface with support for two IDE channels. These two IDE channels are for IDE1 and SATA1/2/3/4 connectors use. Select “Enabled” to activate the first and/or second IDE interface. Select “Disabled” to deactivate the interface if you are going to install a primary and/or secondary add-in IDE interface. -
Page 27: Onboard I/O Chip Setup
PEB-7605 Series User’s Manual USB Mouse Support Enables support for USB attached mouse. Options: Disabled (default)、Enabled Audio Device This item allows you to control the onboard audio. Options: Auto (default)、Disabled Onboard LAN 1 Device Enables support for USB attached mouse. Options: Disabled (default)、Enabled Onboard LAN Boot ROM This item allows you to control the onboard audio. -
Page 28: Onboard Fdc Controller
PEB-7605 Series User’s Manual Onboard FDC Controller Select “Enabled” if your system has a floppy disk controller (FDC) installed on the system board and you wish to use it. If you install an add-in FDC or the system has no floppy drive, select “Disabled”. Options: Enabled (default)、Disabled Onboard Serial Port 1 Select an address and corresponding interrupt for the first/ second serial port.Options: Disabled、3F8/IRQ4 (default for port1)、... -
Page 29: Power Management Setup
PEB-7605 Series User’s Manual 4.7 Power Management Setup... -
Page 30: Acpi Suspend Mode
PEB-7605 Series User’s Manual ACPI Suspend Mode This item specifies the power saving modes for ACPI function. Available options are: 1. S1 (POS) The S1 state is low power state. In this state, no system context (CPU or Chipset) is lost and the hardware maintains all system contexts. -
Page 31: Pnp/Pci Configurations
PEB-7605 Series User’s Manual Date (of Month) Alarm You can choose which date of the month the system will boot up. This field is only configurable when “RTC Wake Up” is set to “Enabled”. Time (hh:mm:ss) Alarm You can choose the hour, minute and second the system will boot up. This field is only configurable when “RTC Wake Up” is set to “Enabled”. -
Page 32: Irq Resources
PEB-7605 Series User’s Manual Reset Configuration Data If you just install a new hardware or modify your computer＇s hardware configuration, the BIOS will automatically detect the changes and reconfigure the ESCD(Extended System Configuration Data). Therefore, there is usually no need to manually force the BIOS to reconfigure the ESCD. -
Page 33: Pc Health Status
PEB-7605 Series User’s Manual PCI / VGA Palette Snoop This option is only useful if you use an MPEG card or an add-on card that makes use of the graphics card's Feature Connector. It corrects incorrect color reproduction by "snooping" into the graphics card's framebuffer memory and modifying (synchronizing) the information delivered from the graphics card's Feature Connector to the MPEG or add-on card. -
Page 34: Frequency/Voltage Control
PEB-7605 Series User’s Manual 4.10 Frequency/Voltage Control This item allows you to adjust your CPU core voltage. Options: 0.85~1.9. The default depends on your CPU. Auto Detect PCI Clk This item is setting the PCI Clock be automation detect . Option Enable(default) , Disable. -
Page 35: Set Supervisor Password
PEB-7605 Series User’s Manual 4.11 Set Supervisor Password This feature consists of two options -- Set Password as well as Security Option. If you set a password for security, the Security Option will enable you to determine whether the code needs to be entered during the boot process or when you enter the BIOS settings. -
Page 36: Load Fail-Safe Defaults
PEB-7605 Series User’s Manual 4.13 Load Fail-Safe Defaults 4.14 Load Optimized Defaults... -
Page 37: Save & Exit Setup
PEB-7605 Series User’s Manual Load System Default Settings To avoid errors, this option allows you to recover the original defaults of BIOS. In fact, this is the first skill you should know as you try to set other defaults of BIOS.