The EW28650 provides a managed Ethernet port, a transparent RJ-45 jack, and a 2.4GHz 802.11b/g/n wireless access point. The EW28650 requires a single power over ethernet cable drop to...
1-3 Precautions Never remove or open the cover. You may suffer serious injury if you touch these parts. Never install the system in wet locations. 1-4 Aspects Figure 1 In-wall Access Point Aspect EW28650: In-wall Wireless Access Point...
The front panel of the In-wall Access Point shown below. Figure 2 In-wall Access Point Front Panel RJ-45 Transparent Port RJ-45 Ethernet Connector WPS Button Reset Button WLAN SYSTEM POWER LINK Figure 3 In-wall Access Point Front Panel EW28650: In-wall Wireless Access Point...
The In-wall Access Point has established a valid wireless connection. Green The wireless connection is active. (Blinking) 1-4-2 Rear Panel The rear panel of the In-wall Access Point 10. RJ-45 Ethernet Connector (802.3af PoE) 11. RJ-45 Transparent Figure 4 In-wall Access Point Rear Panel EW28650: In-wall Wireless Access Point...
One Link 10/100M Link/Activity LED One LAN 10M/100M Link/Activity LED One Wireless Link/Activity LED One System LED Environment Conditions Operating Temperature: 0 to 50°C Storage Temperature: -10 to 60°C Operating Humidity: 10~80% non-condensing. Storage Humidity: 10% to 90% non-condensing EW28650: In-wall Wireless Access Point...
Step 1:Slide the bracket to align with the screw holes on the In-wall Access Point and fasten the bracket tightly with the screws. Step 2:Slide the EW28650 into the bottom faceplate and fasten tightly into the bottom faceplate until it is flush with the wall.
UTP network Cable with a RJ-45 connection Note: Prepare twisted-pair cables with RJ-45 plugs. Use Category 5e or Category 6 cable for all connections. Make sure that each cable does not exceed 328 feet (Approximately 100 meters). EW28650: In-wall Wireless Access Point...
Default Username and Password: admin/admin Note : Set the IP segment of the administrator’s computer to be in the same range as EW28650 for accessing the system. Do not duplicate the IP address used here with the IP address of EW28650 or any other device within the network Step1:Click StartSettingControl Panel.
Page 13
Step 3:Launch your web browser, and then enter the factory default IP address 192.168.10.1 in your browser’s (URL) location box. Press Enter. Step 4:The EW28650 login screen will appear. In the Username and Password field, type the factory default username admin and password admin and click Submit. The EW28650 setup screen will appear.
EW28650 User’s Manual rev. 3/14 PoE (Power over Ethernet) Application Note: To use the EW28650’s PoE feature, follow the instructions for your specific PoE device. EW28650: In-wall Wireless Access Point...
Configuration Program, please press the reset button to load the device to manufacturer defaults. If the In-wall Access Point doesn’t send any packets within 5 minutes (default), the In-wall Access Point will logout automatically. Proxy needs to set disable first when administrator accesses admin User Interface EW28650: In-wall Wireless Access Point...
TCP/IP settings from your gateway or IP router. If your device comes with this feature, please enable “DHCP Client.” Figure 9 DHCP Client Setting Screen Item Default Description MTU Setting 1500 MTU (Maximum Transfer Unit) specifies maximum transmission unit size. EW28650: In-wall Wireless Access Point...
Page 18
MTU (Maximum Transfer Unit) specifies maximum transmission unit size. VLAN ID Setting Item Default Description VLAN ID Disable Enable or Disable Ethernet and wireless VLAN ID Function Ethernet Empty Defines the VLAN ID for the port (1~4095). VLAN ID EW28650: In-wall Wireless Access Point...
Select of channel width of Auto 20/40 MHz or 20MHz Adjust the output power of the system to get the appropriate Transmit Power 25% coverage for your wireless network. Select from 10% to 100% that is required for your specific environment. EW28650: In-wall Wireless Access Point...
Preamble Type preamble when sending and receiving packets. The setting menu allows you to select a long, short or dynamic preamble type. Click Apply button to save the new settings. EW28650: In-wall Wireless Access Point...
(range from 1 - 4095), and the access point will group client devices (and network traffic) using that SSID into that specific VLAN ID. For example, you could enable encryption and authentication on one SSID to protect private applications, and no security on another SSID to maximize open connectivity for public usage. EW28650: In-wall Wireless Access Point...
Page 22
Wi-Fi Protected Access Encryption Pre-shared Key Empty Enter a pre-shared key from 8 to 63 case sensitive ASCII characters. Group Key 86400 Seconds Enter a number in the field to set the force re-keying interval. Re-Keying EW28650: In-wall Wireless Access Point...
Page 23
Enter 26 characters (case sensitive) for Hex 128-bit WEP Key. Click Apply button to save the new settings. Figure 14 Restart Dialog Box Click Apply button, the restart dialog box appears. Click on Apply to restart the system. EW28650: In-wall Wireless Access Point...
Page 25
This function allows remote user to ping the In-wall Allow remote user to ping Access Point through the Internet. Ping is normally Enable the device used to test the physical connection between two devices, to ensure that everything is working correctly. EW28650: In-wall Wireless Access Point...
1. Before downloading the new firmware, users must save the configuration file to restore the configuration parameters of the device. 2. Do not turn the power off during the upgrade process. This will damage the unit. EW28650: In-wall Wireless Access Point...
Page 27
Enter the file name and location in the File Synchronization field. Click the button to display synchronization file example. Frequency Weekly Set the firmware upgrade time. The default value is “Weekly”. Figure 18 Synchronization File Sample Code EW28650: In-wall Wireless Access Point...
Page 28
EW28650 User’s Manual rev. 3/14 Note: Do not turn the power off during the upgrade process. This will damage the unit. EW28650: In-wall Wireless Access Point...
Enter the IP address of TFTP Server. Address File Name Empty Enter the file name in the File Name field. Reset the system back Erases all settings; resets back to factory settings. to factory defaults EW28650: In-wall Wireless Access Point...
The address of the NMS. The default settings for the NMS Networking are “ANY.” Address Privileges Read Choose “Read”, “Write”, “Trap Recipients” and “All” for different privileges. The defaults are all “read.” Status Valid/Invalid Chosen “Valid” or “Invalid”. The default setting of entry is “Invalid.” EW28650: In-wall Wireless Access Point...
If your In-wall Access Point is not operating correctly, you can choose this option to display the restart screen. Clicking the apply button will restart the In-wall Access Point, with all of your settings remaining intact. Figure 22 Restart Screen EW28650: In-wall Wireless Access Point...
100Mbps: Use EIA/TIA-568-100-Category 5 cable. Figure 24 RJ-45 Connector and Cable Pins Note: To prevent loss of signal, make sure that the length of any twisted-pair connection does not exceed 100 meters (approximately 328 feet). EW28650: In-wall Wireless Access Point...
This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. EW28650: In-wall Wireless Access Point...
Length of warranty: The EW28650 is warranted for one (1) year for all parts and labor from the date of receipt. Who the warranty protects: This warranty is valid only for the original purchaser.