Ricon 20-600H Operator's Manual

Ricon 20-600H Operator's Manual

6” benchtop jointer with helical-style cutterhead

Advertisement

Quick Links

20-600H
6" Benchtop Jointer
with Helical-Style Cutterhead
262149
Operator's Manual
Record the serial number and date of purchase in your manual for future reference.
Serial Number: _________________________
Date of purchase: _________________________
For technical support or parts questions, email techsupport@rikontools.com or call toll free at (877)884-5167
www.rikontools.com
20-600HM1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 20-600H and is the answer not in the manual?

Questions and answers

Summary of Contents for Ricon 20-600H

  • Page 1 20-600H 6” Benchtop Jointer with Helical-Style Cutterhead 262149 Operator’s Manual Record the serial number and date of purchase in your manual for future reference. Serial Number: _________________________ Date of purchase: _________________________ For technical support or parts questions, email techsupport@rikontools.com or call toll free at (877)884-5167 www.rikontools.com...
  • Page 2: Table Of Contents

    TABLE OF CONTENTS Specifications........................2 Safety Instructions ......................3 - 6 Getting To Know Your Machine ....................7 Contents of Package .....................7 - 8 Installation ........................8 Assembly ........................9 - 11 Operation ........................12 - 13 Adjustments.......................14 - 17 Maintenance ........................18 Electricals & Wiring Diagram ..................5 & 18 Troubleshooting ......................19 Parts Diagrams &...
  • Page 3: Safety Instructions

    SAFETY INSTRUCTIONS IMPORTANT! Safety is the single most important consideration in the operation of this equipment. The following instructions must be followed at all times. Failure to follow all instructions listed below may result in electric shock, fire, and/or serious personal injury. There are certain applications for which this tool was designed.
  • Page 4 SAFETY INSTRUCTIONS 12. KEEP PROTECTIVE GUARDS IN PLACE AND IN 25. ALWAYS WEAR A DUST MASK TO PREVENT WORKING ORDER. INHALING DANGEROUS DUST OR AIRBORNE PARTICLES, including wood dust, crystalline silica dust 13. AVOID ACCIDENTAL STARTING. Make sure that and asbestos dust. Direct particles away from face and the power switch is in the “OFF”...
  • Page 5: Electricals & Wiring Diagram

    SAFETY INSTRUCTIONS EXTENSION CORDS ELECTRICAL SAFETY THE USE OF AN EXTENSION CORD THIS TOOL MUST BE GROUNDED WITH THIS MACHINE IS NOT RECOMMENDED. For WHILE IN USE TO PROTECT THE OPERATOR FROM best power and safety, plug the machine directly into a ELECTRIC SHOCK.
  • Page 6: Number Of Cutterhead Insert Rows

    SAFETY INSTRUCTIONS SPECIFIC SAFETY INSTRUCTIONS FOR JOINTERS This machine is intended for the surfacing of natural, solid woods. The permissible workpiece dimensions must be observed (see Technical Specification). Any other use not as specified, including modification of the machine or use of parts not tested and approved by the equipment manufacturer can cause unforeseen damage and invalidate the warranty.
  • Page 7: Getting To Know Your Machine

    PARTS DIAGRAM AND PARTS LIST CONTENTS OF PACKAGE Model 20-600H Jointer is shipped complete in one box. Unpacking and Clean-up 1. Carefully remove all contents from the shipping carton. Compare the contents with the list of contents to make sure that all of the items are accounted for, before discarding any packing material.
  • Page 8: Installation

    THE MACHINE MUST NOT BE PLUGGED IN AND THE POWER SWITCH MUST BE IN THE 'OFF' POSITION UNTIL ASSEMBLY IS COMPLETE. NOTE: The 20-600H Jointer requires minimal TOOLS REQUIRED FOR ASSEMBLY assembly, and therefore the machine can be mounted...
  • Page 9: Assembly

    ASSEMBLY THE MACHINE MUST NOT BE PLUGGED IN AND THE POWER SWITCH MUST BE IN THE 'OFF' POSITION UNTIL ASSEMBLY IS COMPLETE. FENCE ASSEMBLY PROCEDURE 1. Assemble the Fence Bracket (A) to the jointer base (B). Use the four Socket Button Head Screws (C) to lock the bracket in place.
  • Page 10 ASSEMBLY THE MACHINE MUST NOT BE PLUGGED IN AND THE POWER SWITCH MUST BE IN THE 'OFF' POSITION UNTIL ASSEMBLY IS COMPLETE. CONTINUED FROM PAGE 9 5. With the tilt lock lever assembly in place on the UNDERSIDE positioned fence sliding bracket and fence bracket, put the special rectangular shaped Nut (A) onto the VIEW OF lever handle’s threaded shaft.
  • Page 11 ASSEMBLY DUST PORT ASSEMBLY THE MACHINE MUST NOT BE PLUGGED IN AND THE POWER SWITCH MUST BE IN A Dust Port (A) is supplied with the jointer to help THE OFF POSITION UNTIL ALL ADJUSTMENTS ARE connect it to a standard 2-1/2 inch vacuum hose. COMPLETE.
  • Page 12: Operation

    OPERATION NOTICE: This operations section was designed to give instructions on the basic operations of this jointer. However, it is in no way comprehensive of every jointer operation. It is strongly recommended that you read books, trade magazines, or get formal training to maximize the potential of your jointer NOTICE: This jointer is designed to surface natural wood ONLY.
  • Page 13: Operation

    OPERATION FEEDING THE WORKPIECE Place the workpiece on top of the right, infeed table. The workpiece will be cut on its underside by the rotating cutterhead knives. When jointing, the feeding direction of the workpiece is right-to-left over the cutterhead. FIG. 14. 1.
  • Page 14: Adjustments

    ADJUSTMENTS THE MACHINE MUST NOT BE PLUGGED IN AND THE POWER SWITCH MUST BE IN THE OFF POSITION UNTIL ALL ADJUSTMENTS ARE COMPLETE. FENCE ADJUSTMENTS 1. To move the fence across the table, loosen the lock lever (A), slide the fence to the desired position on the FIG.
  • Page 15 ADJUSTMENTS ROTATING OR REPLACING KNIFE INSERTS THE MACHINE MUST NOT BE PLUGGED IN AND THE POWER SWITCH MUST BE IN This machine has a helical-style cutterhead with six THE OFF POSITION UNTIL ALL ADJUSTMENTS ARE rows of carbide knife inserts. Each of the 12 inserts COMPLETE.
  • Page 16 ADJUSTMENTS TABLE ADJUSTMENTS THE MACHINE MUST NOT BE PLUGGED IN AND THE POWER SWITCH MUST BE IN The infeed and outfeed tables are preset at the THE OFF POSITION UNTIL ALL ADJUSTMENTS ARE factory to be aligned with the cutterhead. To ensure COMPLETE.
  • Page 17: Adjustments

    ADJUSTMENTS CONTINUED FROM PAGE 16 5. Do the same measurement with the straight edge from the infeed table, to the same insert cutters that were used to measure the outfeed table. 6. Once the infeed and outfeed tables are aligned with the cutterhead cutters, the tables need to be checked to confirm that their surfaces are parallel with each other - ends not tilting or angling down or up from the...
  • Page 18: Maintenance

    MAINTENANCE Turn the power switch “OFF” and disconnect the plug from the outlet prior to adjusting or maintaining the machine. DO NOT attempt to repair or maintain the electrical components of the motor. Contact a qualified service technician for this type of maintenance. 1.
  • Page 19: Troubleshooting

    TROUBLESHOOTING FOR YOUR OWN SAFETY, ALWAYS TURN OFF AND UNPLUG THE MACHINE BEFORE CARRYING OUT ANY TROUBLESHOOTING. SYMPTOM POSSIBLE CAUSES SOLUTIONS Machine will not start. 1. No power 1. Check power source, plug and wiring. 2. Blown fuse 2. Check fuse, replace if it is blown. 3.
  • Page 20: Parts Diagrams & Parts Lists

    PARTS DIAGRAM NOTE: Please reference the Manufacturer’s Part Number when calling for Replacement Parts. For Parts under Warranty, the Serial Number of your machine is required. 20-600H 6” JOINTER...
  • Page 21 PARTS LIST PART PART QTY. DESCRIPTION DESCRIPTION QTY. P20-600H-3 OUTFEED SUPPORT SET SCREW M6x16L P20-600H-56 SET SCREW M6x8L P20-600H-4 HEX NUT M6xP1.0 P20-600H-57 END COVER P20-600H-5 ADJUSTING ROD P20-600H-58 BUTTON HD SCREW M6x12L P20-600H-6 SHAFT P20-600H-59 SELF TAP SCREW 1/4”x 5/8” P20-600H-7 END COVER P20-600H-62...
  • Page 22: Accessories

    ACCESSORIES 25-499 HSS INSERT CUTTERS - Pack of 10 with 2 pre-sharpened edges 25-499C CARBIDE INSERT CUTTERS - PK 10 with 2 pre-sharpened edges 25-410 PLANER STAND 29-1/4” high, top measures 23” x 14”, base 31” x 22”. All steel design. Requires making wood/plywood top (not included) to mount machines.
  • Page 23: Warranty

    WARRANTY...
  • Page 24 20-600H For more information: 16 Progress Road Billerica, MA 01821 877-884-5167 / 978-528-5380 techsupport@rikontools.com www.rikontools.com 20-600HM1...

Table of Contents