Table of Contents
Advertisement
10
ULTRATONE KXD15/KXD12
ULTRATONE KXD15/KXD12 Controls
(1)
(2)
(8)
(9)
(17)
(19)
(18)
(24)
(3)
(4) (5)
(6)
(7)
(10) (11) (12) (13)
(14)
(15)
(16)
(20)
(21)
(22)
(23)
(25)
(26)
11
Quick Start Guide
Step 2: Controls
(EN)
(12)
SIG LED lights up when the eff ects processor
receives an input signal.
(13)
FX display shows the currently
selected preset.
(14)
LEVEL control in the master section is used to
(1) FX controls adjust the channel 1-4 signal
adjust the main output volume.
level at the input of the integrated
(15)
SHAPE button applies a special fi lter to the
eff ects processor.
MASTER output to increase the sound's clarity
(2) TO LINE OUT button routes the channel 4
and defi nition in noisy environments.
signal to the LINE OUT output without eff ects.
(16)
PHONES LEVEL control adjusts the
If you press both the TO MAIN and TO LINE
headphones output level.
button, channel 4 will be equal to channels
1 - 3. The signal will be routed to the speakers
(17)
POWER switch turns the unit on or off .
and the LINE OUT output including eff ects.
You should always make sure that the POWER
switch is in the "Off " position when initially
(3) GRAPHIC EQ adjusts specifi c frequencies in
connecting the unit to the mains.
the sound spectrum.
(18)
POWER SOURCE jack accepts the included IEC
(4) MULTI-FX PROCESSOR unit adds a selected
power cable.
sound eff ect to any channels which have their
FX knob turned up. Eff ects include reverb,
(19)
LINE OUT connectors send out a post-EQ
chorus, delay, and pitch shifter.
audio signal to external devices. The XLR
connectors provide a balanced signal
(5) PROGRAM [PUSH] knob controls the eff ects
suitable for connection to mixing or
settings. Rotate this knob to scroll through
recording consoles, while the ¼ " connectors
eff ects patches, and push to select a patch.
provide an unbalanced signal suitable for
(6) FX RET knob controls the amount of eff ects
additional amplifi ers or other line-level
added to the main mix.
devices. Both XLR and ¼ " connectors may be
used simultaneously.
(7) PHONES jack allows connection of
headphones using ¼" TRS stereo connectors.
(20)
STEREO LINK connection allows for true
stereo operation between two ULTRATONE
(8) LEVEL controls adjust the signal level of
amplifi ers. You can connect the OUT of one
channels 1-4.
ULTRATONE to the LINK IN of another keyboard
(9) TO MAIN routes the channel 4 signal to the
amp which then serves as slave to achieve a
speakers without eff ects. When disengaged,
true stereo sound.
the channel 4 signal normally routes to the
(21)
AUX IN connection accepts signals from CD
PHONES output without eff ects.
players, MP3 players or other sound sources
(10)
FBQ button activates the FBQ Feedback
using RCA connectors.
Detection system. The frequencies causing
(22)
LINE inputs for channels 2-4 accept
feedback are shown by the brightly lit fader
unbalanced stereo signals through paired
LEDs. Simply lower the level of the respective
¼" TS connectors. For mono input signals
frequency range until feedback disappears
please use the L (MONO) connector.
and the LED goes out.
(23)
LINE/MIC input section for channel 1
(11)
CLIP LED lights when the signal from the
features an additional XLR connection in
channel FX sends overloads the processor.
addition to dual ¼ " TS connectors. Use the
When the CLIP LED lights up please reduce the
XLR connection for balanced signals from
eff ects input signal by using the respective
microphones or other devices (+15 V phantom
FX control(s).
power is available to power condenser
microphones). Both XLR and ¼ " connectors
can be used simultaneously, while the channel
1 LEVEL control adjusts the signal level for
both inputs.
(24)
GND LIFT switch disconnects
(switch pressed) the ground connection
at the LINE OUT XLR outputs to eliminate
hum and other noise resulting from
ground loops.
(25)
SUB OUT connector provides the
line-level mono subwoofer signal for
connection to the input of a power amp or
active subwoofer.
(26)
FOOT SW jack connects an optional
footswitch using a footswitch using a
¼ " TS plug to activate/deactivate the
eff ects processor.
Hide quick links:
Advertisement
Table of Contents
