Page 6
UF83** OPTICAL DIGITAL AUDIO OUT SVC ONLY VIDEO AUDIO VIDEO AUDIO MONO...
Page 8
43UF680T-TA 49UF680T-TA 55UF680T-TA 65UF680T-TA 50UF830T-TA 58UF830T-TA 43UF680Y-TA 49UF680Y-TA 55UF680Y-TA 65UF680Y-TA 50UF830Y-TA 58UF830Y-TA (mm) 971 x 628 x 180 1104 x 701 x 237 1240 x 778 x 237 1460 x 902 x 263 1122 x 709 x 237 1298 x 815 x 263 (mm) 971 x 570 x 56.4...
Page 9
OWNER’S MANUAL Safety and Reference LED TV* * Disclaimer LG LED TV applies LCD screen with LED backlights. Please read this manual carefully before operating your set and retain it for future reference. www.lg.com *MFL68702232* P/NO : MFL68702232 (1511-REV03) Printed in Korea...
Safety instructions Please read these safety precautions carefully before using the product. Make sure to connect Mains cable to compliant AC mains socket with Grounded earth pin. (Except for devices which are not grounded on WARNING earth.) Otherwise possibility you may be electrocuted or injured. Insert power cable plug completely into wall socket otherwise if not Do not place the TV and/or remote control in the following secured completely into socket, fire ignition may break out.
Page 11
Do not plug too many electrical devices into a single multiple electrical Do not put or store inflammable substances near the product. There is a outlet. Otherwise, this may result in fire due to over-heating. danger of combustion/explosion or fire due to careless handling of the inflammable substances.
Page 12
Only use an authorized AC adapter and power cord approved by discretion. Fire or electric shock accident can occur. LG Electronics. Otherwise, this may result in fire, electric shock, Contact the service centre for check, calibration or repair. malfunction or product deformation.
Page 13
If you intend to mount the product to a wall, attach VESA standard mounting interface (optional parts) to the back of the product. When you install the set to use the wall mounting bracket (optional parts), fix it carefully so as not to drop. Signal from Remote Control can be interrupted due to external/internal Only use the attachments / accessories specified by the manufacturer.
Page 14
Prevent dust collecting on the power plug pins or outlet. This may cause When unplugging the cable, grab the plug and unplug it, by pulling at a fire hazard. the plug. Don’t pull at the cord to unplug the power cord from the power board, as this could be hazardous.
Page 15
Viewing 3D imaging (Only 3D models) WARNING The panel is a high technology display product with resolution of two Viewing environment million to six million pixels. You may see tiny black dots and/or brightly coloured dots (red, blue or green) at a size of 1 ppm on the panel. This • ...
Page 16
Cautions when using the 3D glasses < 18 mm • Make sure to use LG 3D glasses. Otherwise, you may not be able to view 3D videos properly. • Use a certified cable with the HDMI logo attached. • Do not use 3D glasses instead of your normal glasses, sunglasses or • ...
Cinema 3D Glasses Magic Remote Smart Camera AG-F***DP LG Audio Device Dual Play Glasses Maintenance • When transporting a large TV, there should be at least 2 people. • When transporting the TV by hand, hold the TV as shown in the following illustration.
Using the joystick button Mounting on a table You can simply operate the TV functions, pressing or moving the joystick (Image shown may differ from your TV.) button up, down, left or right. 1 Lift and tilt the TV into its upright position on a table. NOTE • ...
We recommend the use of LG’s wall mount bracket. LG’s wall mount • Do not over tighten the screws as this may cause damage to the TV bracket is easy to move with cables connected.
Connections (notifications) • When installing the wall mounting bracket, use the adhesive label or protective cover provided. The adhesive label or protective cover will protect the opening from accumulating dust and dirt. (Only Connect various external devices to the TV and switch input modes to when the label or cover is provided) select an external device.
CI module connection CAUTION (Depending on model) • Do not mix old and new batteries, as this may damage the remote control. View the encrypted (pay) services in digital TV mode. • In Analogue TV and some countries, some remote control buttons • ...
GUIDE Q.VIEW PAGE Magic remote functions RECENT MY APPS (Depending on model) When the message “Magic remote battery is low. Change the battery.” is displayed, replace the battery. To replace batteries, open the battery cover, replace batteries (1.5 V AA) LIVE MENU matching the...
wxyz pqrs LIST INFO EXIT Registering magic remote How to register the magic remote To use the Magic Remote, first pair it with your TV. 1 Put batteries into the Magic Remote and turn the TV on. GUIDE 2 Point the Magic Remote at your TV and press the Wheel (OK) on the remote control.
The TV turns off suddenly. LG Electronics will also provide open source code to you on CD-ROM • Check the power control settings. The power supply may be for a charge covering the cost of performing such distribution (such interrupted.
Specifications Digital TV Analogue TV (Depending on Country) (Depending on Country) PAL B/B, PAL B/G, PAL Wireless module Television DVB-T/T2 D/K, PAL-I • Because band channel used by the country could be different, the system DVB-T/T2/C/S/S2 SECAM B/G, SECAM D/K user can not change or adjust the operating frequency and this NTSC-M product is set for the regional frequency table.
5. To locate a nearest collection centre or call for pick-up (limited area only) for disposal of this appliance, please contact Toll Free No. 1800-315-9999 / 1800-180-9999 for details. All collection centre and pick up facilities are done by third parties whith LG Electronics India Pvt. Ltd. Merely as a facilitator. For more detailed information, please visit : http://www.lge.com/in.
Page 28
(Only DTV) Record the model number and serial number of the TV. Refer to the label on the back cover and quote this information to your dealer when requiring any service. MODEL SERIAL...
OWNER’S MANUAL EXTERNAL CONTROL DEVICE SETUP Please read this manual carefully before operating the set and retain it for future reference. www.lg.com...
KEY CODES KEY CODES • This feature is not available for all models. Code Code Function Note Function Note (Hexa) (Hexa) CH +, PR + R/C Button List R/C Button CH -, PR - R/C Button Exit R/C Button Volume + R/C Button PIP(AD) R/C Button...
Page 31
(TV) (PC) • LGTV supports PL2303 chip-based (Vendor ID : 0x0557, Product ID : 0x2008) USB to serial converter RS-232C IN which is not made nor provided by LG. (CONTROL & SERVICE) (TV) (PC) • It can be purchased from computer stores that carry accessories for IT support professionals.
Page 32
EXTERNAL CONTROL DEVICE SETUP (TV) (PC) (TV) (PC) Phone jack Type RS-232C IN • You need to purchase the phone-jack to RS-232 cable required for the connection between the PC and (CONTROL & SERVICE) (PC) (TV) the TV, which is specified in the manual. RS-232C IN (CONTROL &...
EXTERNAL CONTROL DEVICE SETUP Communication Parameters • Baud rate : 9600 bps (UART) • Stop bit : 1 bit • Data length : 8 bits • Communication code : ASCII code • Parity : None • Use a crossed (reverse) cable. Command reference list (Depending on model) DATA...
Page 34
EXTERNAL CONTROL DEVICE SETUP Transmission / Receiving Protocol Transmission [Command1][Command2][ ][Set ID][ ][Data][Cr] [Command 1] : First command to control the TV. (j, k, m or x) [Command 2] : Second command to control the TV. [Set ID] : You can adjust the [Set ID] to choose desired monitor ID number in option menu. Adjustment range in TV is 1 to 99.
Page 35
EXTERNAL CONTROL DEVICE SETUP * Commands may work differently depending on model and signal. 01. Power (Command: k a) Ack [d][ ][Set ID][ ][OK/NG][Data][x] ► To control Power *On or Off of the set. * In case of video mute on only, TV will display On Transmission[k][a][ ][Set ID][ ][Data][Cr] Screen Display(OSD).
Page 36
EXTERNAL CONTROL DEVICE SETUP Data Min : 00 to Max : 64 * (Depending on model) Ack [i][ ][Set ID][ ][OK/NG][Data][x] 14. Bass (Command: k s) 09. Tint (Command: k j) ► To adjust Bass. ► To adjust the screen tint. You can also adjust in the AUDIO menu.
Page 37
EXTERNAL CONTROL DEVICE SETUP Set ID = All = 00 5th Band 20(decimal) Data 00 & 01 = Channel Data is 10 = 00 0a Acknowledgement [v][ ][Set ID][ ][OK/NG][Data][x] Data 02 = Analog Antenna TV = 00 Result = ma 00 00 0a 00 * It depends on model, and can adjust when sound mode is EQ adjustable value.
Page 38
EXTERNAL CONTROL DEVICE SETUP Number Data 05 = Digital Antenna TV = 02 - 22 : Antenna TV (DTV) – Don’t Use Physical Total = ma 00 00 00 11 00 01 02 Channel Number - 26 : Cable TV (CADTV) - Don’t Use Physical 2.
Page 39
11 11 EXTERNAL CONTROL DEVICE SETUP 24. Input select (Command: x b) (Main Picture Input) ► To select input source for main picture. Transmission [x][b][ ][Set ID][ ][Data][Cr] Data X : don’t care 00 : DTV 01 : CADTV 02 : Satellite DTV 10 : ATV Ack [t][ ][Set ID][ ][OK][Data00][Data01][Data02] ISDB-BS (Japan)
Page 40
EXTERNAL CONTROL DEVICE SETUP 27. Auto Configure (Command: j u) (Depending on model) ► To adjust picture position and minimize image shaking automatically. It works only in RGB (PC) mode. Transmission [j][u][ ][Set ID][ ][Data][Cr] Data 01 : Run Auto Configure Ack [u][ ][Set ID][ ][OK/NG][Data][x]...