Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Burk Plus-X Dual IP-8
Summary of Contents for Burk Plus-X Dual IP-8
- Page 1 Plus-X Dual IP-8 Adapter Installation and Operation Manual...
-
Page 2: Table Of Contents
Installation .............................. 4 Software Configuration .......................... 5 Importing ARC-16 Settings ........................7 Uploading New Firmware ........................7 Troubleshooting ............................. 7 Getting Help ............................8 Warranty ..............................8 Appendix A: Specifications ........................9 Copyright © 2011 Burk Technology, Inc. Rev. B... -
Page 3: Introduction
ARC-16 to the ARC Plus Remote Control. The Plus-X Dual IP-8 Adapter communicates with the ARC Plus via LAN/WAN, allowing installation anywhere a network connection is available. The Plus-X Dual IP-8 Adapter is part of the Plus-X family of Ethernet I/O products designed for the ARC Plus. Installation Note... -
Page 4: Compatibility
AutoPilot® 2010 software 2.5.0, 2.6.0 recommended * If using any version of AutoLoad Plus earlier than 2.3.0, you will need to download the Plus-X Dual IP-8 Adapter AutoLoad definition XML file from www.burk.com. The onboard web interface is compatible with Internet Explorer version 8 or newer, Firefox, Chrome, and other modern web browsers. -
Page 5: Front Panel Indicators
Press and hold the MASTER INIT button on the rear panel for three seconds. This will reset the Plus-X Dual IP-8 Adapter to its factory default settings. Settings Click the Settings link on web page header to access the Plus-X Dual IP-8 Adapter settings. Fill out the following fields: ... -
Page 6: Installation
Plus-X Dual IP-8 Adapter Settings Installation After entering the configuration settings, you are ready to install the Plus-X Dual IP-8 Adapter in its permanent location. Simply move the IP-8 cables from the ARC-16 to the Plus-X Dual IP-8 Adapter. Connect the Plus-X Dual IP-8 Adapter to the LAN/WAN, if it is not connected already. -
Page 7: Software Configuration
Software Configuration Now that the Plus-X Dual IP-8 Adapter is installed on the network, you are ready to add the unit to the ARC Plus using AutoLoad Plus. AutoLoad Plus is included with the ARC Plus, and may also be downloaded from www.burk.com. - Page 8 3. Select the Plus-X Dual IP-8 Adapter channel you wish to use. 4. Click OK. Once mapped, each Plus-X Dual IP-8 Adapter channel will appear on the front panel of the ARC Plus, in AutoPilot, on the ARC Plus web page, and will be accessible via the ESI.
-
Page 9: Importing Arc-16 Settings
You can load new firmware to the Plus-X Dual IP-8 Adapter using its onboard web interface. Navigate to the IP address of the Plus-X Dual IP-8 Adapter, log on and click the Upload Firmware link. Click the Browse button to select the firmware file, then click Upload to load the new firmware. The Plus-X Dual IP-8 Adapter will reboot after the firmware upload is complete. -
Page 10: Getting Help
5PM Eastern time. Warranty Burk Technology, Inc. warrants the Plus-X Dual IP-8 Adapter to be free of defects in materials and workmanship for a period of 24 months from the date of purchase. Equipment will be repaired or replaced at the option of Burk Technology and returned freight prepaid to the customer. Damage due to abuse or improper operation or installation of the equipment or caused by fire or flood or harsh environment is not to be covered by this warranty. -
Page 11: Appendix A: Specifications
-4.5VDC to +4.5VDC Metering Input Accuracy: >99.75% accuracy, full scale Status Input Range: >0 to +28VDC or switch closure Output Types: 32 Open collector outputs (16 raise, 16 lower); maximum 250mA, 28V Plus-X Dual IP-8 Adapter Installation and Operation Manual Rev. B...