Related Manuals for Kingston Technology DATA EXPRESS DE90
Summary of Contents for Kingston Technology DATA EXPRESS DE90
- Page 1 Kingston Technology DE90 DATA EXPRESS Removable 8-Bit Single-Ended SCSI Drive Enclosure...
- Page 2 DE90 ® DATA EXPRESS Removable 8-Bit Single-Ended SCSI Drive Enclosure Installation Manual Part No. D89-0000-0043 A00 September 1996 Kingston Technology Company 17600 Newhope Street Fountain Valley, CA 92708-9885 Phone (714) 438-1850 Fax (714) 438-1847 DE90i-S, Rev. A00 Kingston Technology Company...
-
Page 3: Limited Warranty
Limited Warranty KINGSTON TECHNOLOGY COMPANY (“Kingston”) warrants that this product is free from defects in material and workmanship. Subject to the conditions and limitations set forth below, Kingston will, at its option, either repair or replace any part of this product which proves defective by reason of improper workmanship or materials. Repair parts or replacement products will be provided by Kingston on an exchange basis, and will be either new or refurbished to be functionally equivalent to new. -
Page 4: Table Of Contents
Receiving Frame Front Panel Indicator Conditions ..........2 Table 2: DE90 Shipment Contents ..................5 Table 3: Receiving Frame Mother Board Connector J4 Pin Configuration ....11 Table 4: SCSI Interface Connector J2 ................14 DE90i-S, Rev. A00 Kingston Technology Company... - Page 5 Kingston Technology Company DE90i-S, Rev. A00...
-
Page 6: Introduction
® DATA EXPRESS DE90 General Description The Kingston Technology Data Express ® DE90 is a removable lightweight drive carrier and receiving frame designed to provide durable and reliable mounting for 3.5” SCSI or AT/IDE drives within 5.25" half-height peripheral slots (Figure 1). -
Page 7: The Receiving Frame Front Panel
When the carrier has been unlocked from the receiving frame, these lights will flash as the drive spins down. DO NOT REMOVE THE CARRIER FROM THE RECEIVING FRAME DURING THIS PERIOD to prevent possible drive damage. LEDs Key Lock/Power Switch 0407 Figure 2: Receiving Frame Front Panel Kingston Technology Company DE90i-S, Rev. A00... -
Page 8: The Receiving Frame Rear Panel
= Write Protect = Fault P3, P5 = Not Used Ground P4, P6 = Ground Anode Cathode Reserved Installed Remote ID Select at Factory Connector = Pin 1 0408 Figure 3: Receiving Frame (Rear View) DE90i-S, Rev. A00 Kingston Technology Company... -
Page 9: Data Express Model Numbers
0414 Packaging Materials The Kingston Technology Data Express system is shipped in a container designed to provide protection and prevent damage during shipment. The Data Express unit was carefully inspected before and during the packing procedure at the factory. Bent or broken connectors, or evidence of other physical damage to the Data Express should be reported to the carrier immediately. -
Page 10: Package Contents
Kingston Customer Service Representative in order to receive a Return Material Authorization (RMA) for warranty claims. Locate the serial number labels and record the numbers in the spaces provided below. Receiving Frame: Device Carrier: DE90i-S, Rev. A00 Kingston Technology Company... - Page 11 Introduction Kingston Technology Company DE90i-S, Rev. A00...
-
Page 12: Data Express Installation
Disk drives use a row of pins to provide ground to the ID signals. This row of pins is not used when installing the ID select cable to the carrier connector. Refer to your drive manufacturer's documentation for more information. DE90i-S, Rev. A00 Kingston Technology Company... -
Page 13: Installation
Snap the provided drive cover into place as shown in Figure 4. Drive Cover (Provided) Disk Drive Power Cable I/O Interface Cable/s ID Select Cable Drive Carrier 0413 Drive Mounting Screws (4 plcs) # 6-32 x 1/4" Figure 4: Drive Installation Assembly Kingston Technology Company DE90i-S, Rev. A00... -
Page 14: Figure 5: Typical Scsi Id Select Connections (2Mm Drive Pins)
3-PIN WIRE WRAP p r e CONNECTOR (Provided). Use in place of ID select cable if there is not enough space. Connects to J3. 0412 Figure 5 : Typical SCSI ID Select Connections (2mm Drive Pins) DE90i-S, Rev. A00 Kingston Technology Company... -
Page 15: Figure 6: Quantum 270/540S (1.25Mm Drive Pins)
Express Signal When Using J5, Distribution Board) Remove all Jumpers From JP1 SCSI ID Selection Pins Power SCSI I/O JP1 (located on disk Connector Connector drive PCB) 0416 Figure 6: Quantum 270/540S (1.25mm Drive Pins) Kingston Technology Company DE90i-S, Rev. A00... -
Page 16: Installing The Receiving Frame
SCSI ID = 3 SCSI ID = 4 SCSI ID = 5 SCSI ID = 6 SCSI ID = 7 0419 Figure 7: SCSI ID Select Pin Configuration on Receiving Frame Mother Board (J4) DE90i-S, Rev. A00 Kingston Technology Company... -
Page 17: Figure 8: Data Express Receiving Frame Mounting Holes
Mounting Holes. Self Tapping Screws Not Provided (4 Plcs) Receiving Frame Bottom Side of Side Mounting Holes 0415 Receiving Frame 6-32 x 1/4" Screws Provided (4 Plcs) Figure 8: Data Express Receiving Frame Mounting Holes Kingston Technology Company DE90i-S, Rev. A00... - Page 18 The new drive may need to be formatted or initialized prior to use with the operating system and applications software. Refer to the drive and/or computer manufacturer's documentation for formatting information. DE90i-S, Rev. A00 Kingston Technology Company...
-
Page 19: Scsi Interface Connector J2
-RST -Data Bit 1 -Data Bit P -Ground -MSG -Data Bit 2 Ground -ATN -SEL -Data Bit 3 Ground Ground -C/D -Data Bit 4 Ground -REQ -Data Bit 5 TRMPWR -I/O -Data Bit 6 Kingston Technology Company DE90i-S, Rev. A00... -
Page 20: Appendix A - Attaching/Removing The On/Off Key
4. Rotate the key 180 degrees clockwise (or g r e counter clockwise). 5. Reinstall the pawl into the access hole with the adjustment tool. The key/lock has now been reconfigured. 0418 Figure A-1: Reconfiguring the Key/Lock Mechanism DE90i-S, Rev. A00 Kingston Technology Company... - Page 21 Appendix A - Attaching the On/Off Key Kingston Technology Company DE90i-S, Rev. A00...
-
Page 22: Appendix B - Specifications/Dimensions
8.020" (203.71mm) 8.700" (221.0mm) Weight .8lbs. (.36kg) .6lbs. (.27kg) Plus weight of installed disk drive. With carrier removed. Chassis Reliability/Maintainability MTBF 500,000 Hours MTTR 5 Minutes Preventive Maintenance None Electrical Specifications Input 50mA +12V DE90i-S, Rev. A00 Kingston Technology Company... -
Page 23: Figure B-1: Data Express Physical Dimensions
Appendix B - Specifications/Dimensions 5.875" (149.225mm) 8.700" 1.700" (220.98mm) (43.2mm) Receiving Frame with Carrier 4.625" 8.020" (117.5mm) (203.7mm) ingston Data Express 1.680" (42.7mm) 0406 Carrier Only Figure B-1: Data Express Physical Dimensions Kingston Technology Company DE90i-S, Rev. A00... -
Page 24: Reader's Comments
Are there any changes you would like us to make, either with the hardware itself, or with the installation instructions? Everyone at Kingston Technology is working toward the goal of providing you the highest quality, most cost effective, products available on the market, and we need your comments to guide our efforts. - Page 25 B U S I N E S S R E P LY M A I L FIRST CLASS MAIL PERMIT NO. 10686 SANTA ANA, CA POSTAGE WILL BE PAID BY ADDRESSEE TECHNOLOGY CORPORATION 17600 NEWHOPE STREET FOUNTAIN VALLEY CA 92708-9885 Kingston Technology Comapany DE90i-S, Rev. A00...
Need help?
Do you have a question about the DATA EXPRESS DE90 and is the answer not in the manual?
Questions and answers