Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Team Nisca L201
Summary of Contents for Team Nisca L201
- Page 1 User Manual Laminator L201 Version: L201-K12/V0.02...
-
Page 2: Table Of Contents
Table of contents 1. General information................ . Product description............... 3 Symbols and conventions............3 Intended use............... 4 Safety information..............4 Environmental information............. 5 2. Connection and commissioning............Device overview..............6 Unpacking and setting up the device........7 Connecting the device............8 Connecting to the power supply........... -
Page 3: General Information
1 General information Product description See specification! Symbols and conventions The following symbols and conventions are applied in this user manual. The symbol indicates important information, which must be observed. A failure to do so may lead to injuries. The symbol indicates parts of the device that are hot and should not be touched. Good advice or information regarding important working steps. -
Page 4: Intended Use
Intended use The device is constructed in accordance with the latest engineering practice and per the recognized safety regulations. Nevertheless, danger to the life and limb of the user or third parties or damage to the device and other property may occur when using it. The device must be operated exclusively when in a technically faultless condition, as intended, with an awareness of safety and potential hazards, and in accordance with the operating manual. -
Page 5: Environmental Information
Environmental information The device comprises materials that can be reused when processed by specialist recycling companies. The optimum design of the laminator facilitates a straightforward separation of the recyclable materials. Label the device as scrap and dispose of it in accordance with the legal regulations. -
Page 6: Connection And Commissioning
2 Connection and commissioning Device overview 1 Carrier roller 2 Spacer ring 3 Heated roller 4 RFID module... -
Page 7: Unpacking And Setting Up The Device
Unpacking and setting up the device • Remove the device from its packaging and place on a level surface. • Check the laminator for transport damage. • Check delivery for completeness. Scope of supply: • Laminator • Power adapter • Mains cable Store original packaging for subsequent transportation. -
Page 8: Connecting The Device
Connecting the device Connecting to the power supply ( 24V connection jack The laminator is equipped with an external broad-range power pack for a mains voltage of 100 V to 240 V. Plug the mains cable into an earthed socket and the 24V cable into the 24V device connection jack. -
Page 9: Inserting Film
Inserting film There is a risk of burning on the safety guard for the heated roller (4) When inserting or exchanging patch film proceed as follows: • Switch off the device and let it cool down • Open housing cover •... -
Page 10: Attaching The Laminator To The Printer
3 Attaching the Laminator to the Printer ① Switching off the Printer. Switching off the Laminator. ② Insert the hooks of the Laminator to the holes by the Card Ejection Slot of the Printer. Insert the hooks of the Card Stacker to the holes by the Card Ejection Slot of the Laminator. -
Page 11: Laminating
4 Laminating Switching on the Printer & Laminator ① At first, Switching on the Laminator. The device carries out initialization with a simultaneous self-test. If no error is present, heated roller heating commences. ② Next, Switching on the Printer. If the Laminator is at heating status, the Printer’s display indicates “Initializing / Lami Warm up”. -
Page 12: Driver Setting
Driver Setting For laminating, check the box of “Lamination” in the PR-C201 Printer Driver. ① Select “General” tab, and click “Preferences…” ② In case of laminating front side, select “Ribbon” tab and click “Laminate” button and the “Front” button. Change the option to “Laminate front side”. - Page 13 ③ Laminating the back side, select “Laminate” button and the “Back” button. Change the option to “Laminate back side”.
-
Page 14: Laminating Action
Laminating Action With checking "Lamination" of the Printer Driver, It processes laminating after having performed each processes of printing, magnetic & IC encoding. When the Laminator is connected to the Printer, the card is outputted from Card Ejection Slot of the Laminator, regardless of “Normal Exit” setting. When the Laminator is connected to the Printer, The card is outputted with its last laminating surface upwards, regardless of “Exit Face”... -
Page 15: Configuration
5 Configuration Menu Route Map (Laminator Setup) The different setting options configure the laminator for specific requirements. This is carried out via the printer’s control panel. Refer to the PR-C201 Operation Guide for the control of the control panel. Mode Select Magnetic Encoder Connection ①... -
Page 16: Configuration Settings
Configuration settings ① Connection Showing the connection of the Laminator. Connecting：CONNECT Disconnecting：DISCONNECT ② Version Showing the firmware version. ③ Serial Number Showing the serial number of board. ④ Tag Info Showing the 8-digit tag information. ⑤ Foil Type Setting the film type. Setting range: Patch: Patch (1mil) (always with black marking) HOLO (INDEX): Thin film (Reference) with black marking... - Page 17 ⑦ Lamination Speed Setting of the transport speed of the document during lamination. The correct speed must be experimentally determined with consideration to the lamination temperature, the laminate film and the plastic card. The presetting must be considered a guideline value. In order to carry out a test it is possible to start the motor via Setting range: 4...6...20 mm/s...
- Page 18 ⑫ Foil Position With a change in the plastic card intake range, precise placement of the film is carried out. With an enlarging of the intake range, the lamination of the plastic card starts later. Conversely, with a reduction in the intake range lamination starts earlier. The direction arrows on the display indicate the direction of travel once lamination starts.
-
Page 19: Troubleshooting
6 Troubleshooting Type of errors and elimination If an error occurs then this is signaled by the red ERROR LED whilst the error message is shown on the printer’s display. Different error codes indicate the cause of the problem. "Rectifiable errors" are usually film or transport errors, which are simple to remedy. In a normal case it is possible to recover the error after eliminating the problem and pressing [SET] key, after which the device is once again ready for operation. -
Page 20: Error Messages
Error messages Cause Remedy Error Massage Service Call / C0-01 Service Call / C0-02 Service Call / C0-03 Service Call / C0-04 Service Call / C0-05 Service Call / C0-06 Invalid communication between Service Call / C0-07 the Printer and the Laminator. Service Call / C0-08 Contact service! - Page 21 Error Massage Cause Remedy Service Call / C8-81 No response from tag reader. Check tag reader. Contact service! Service Call / C8-82 Impermissible ADU values Check temperature sensor. Contact service! Service Call / C8-83 No temperature increase to Check temperature sensor. record Contact service Service Call...
-
Page 22: Service
7 Service Firmware upgrade For service purposes the laminator is connected with the computer via the serial interface. A standard cable RS-232 SERIAL SUB D9 connector jack is used. AVR-Bootloader After starting the Windows application it is possible to load new firmware. Prior to this the interface agreements as well as the path for the access to the application code (*.HEX) must be stipulated The download process can be started as follows:...
Need help?
Do you have a question about the L201 and is the answer not in the manual?
Questions and answers