Table of Contents
Advertisement
Quick Links
DogWatch
Product Features and Operating Instructions
IB-200 T
RANSMITTER
T
OP
Power Status Light
B
OTTOM
Frequency
Signal Range
(for Dealer Use Only)
EXT WIRE
INT - Wireless
Boundary wire
EXT - Wired
attachment
Set Up: Wireless / With Wire
The INT/EXT switch on the back of the unit allows you to choose your preferred application. You cannot use
both applications at the same time.
Wireless: When using the IB-200 as a wireless unit (
The signal range can be adjusted up to a maximum of 10 feet in diameter (5 feet in all directions from the
transmitter). Avoid placing the transmitter on or near large metal objects.
With Wire: When using the boundary wire (
and adjust the signal range using both the Signal Range adjustment and by increasing or
decreasing the distance between the separated wires. See instructions on page 3.
®
IB-200
200 is a dual function transmitter designed to be used either
The IB-
as a wireless unit that emits a signal directly from the transmitter
without the use of a boundary wire o o r r it may be installed with a
boundary wire to establish larger or multiple avoidance areas.
Power Status Light
The Power Status Light on the top of the transmitter turns "on" and glows
green when the transmitter is plugged-in and sending a signal. When using
a boundary wire, the Power Status Light turns "on" only when there is a
continuous sign l loop. See instructions on page 3.
Note: The green light may be steady green or blinking green. This depends
of the Frequency setting of the transmitter.
Signal Range
Signal range is the distance the signal radiates from the transmitter or
the boundary wire.
Turn the knob toward the '+' to increase the signal range.
•
This increases the size of the signal field.
Turn the knob toward the '-' to decrease the signal range.
•
This decreases the size of the signal field.
Never adjust the signal range while your pet is wearing the receiver
collar.
lways test the signal field and mark the edge of the field with
warning flags before allowing your pet near the boundary area.
Frequency
This switch controls the broadcast frequency of the signal. Your Dealer will
set this switch for your system. Do
DEALER USE ONLY
INT allows you to use the transmitter as a wireless unit.
EXT allows you to use the transmitter with boundary wire.
)
, you can customize your avoidance zone(s)
EXT
NOT
.
)
, place the unit in the area that you want your pet to avoid.
INT
1
change this setting. It is for
®
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for DogWatch IB-200
Summary of Contents for DogWatch IB-200
- Page 1 INT allows you to use the transmitter as a wireless unit. EXT allows you to use the transmitter with boundary wire. Wireless: When using the IB-200 as a wireless unit ( , place the unit in the area that you want your pet to avoid.
- Page 2 E E s s t t a a b b l l i i s s h h i i n n g g t t h h e e B B o o u u n n d d a a r r y y A A r r e e a a The IB-200 can be used to train your pet to stay within an area or to avoid an area. Set the signal range then place the transmitter in the center of the area where you want to create a signal field or a boundary you do not want your pet to cross.
-
Page 3: Troubleshooting
The boundary wire supplied with the transmitter is a double wire designed to be separated in the areas where you want to create a signal field (the avoidance area). When the two wires are next to one another, there is no signal field. - Page 4 DogWatch Inc., subject to the terms and conditions set forth hereunder, hereby warrants that it will repair or replace, at its own discretion, without charge for parts or labor, the Indoor Product or any part thereof which is found by DogWatch Inc. to be defective by reason of improper workmanship and/or materials for a period of two (2) years from the original date of sale hereunder.
Need help?
Do you have a question about the IB-200 and is the answer not in the manual?
Questions and answers