Contents Specifications ..............5 SAFETY INFORMATION ........... 6 INTRODUCTION ............8 MACHINE (Final paper delivery view) ....... 9 MACHINE (Duplicator delivery view) ...... 10 OPERATION PANEL ..........11 WHERE TO PUT THE SERIPRINTER....12 POWER ON AND OFF ..........13 BASIC OPERATION ..........
Page 3
SeriPrint SA (Pty.) Ltd. SeriPrint, SeriPrinter, SP100II, SP25, SeriInk, SeriLink and all other related brand names are registered trademarks of SeriPrint South Africa (Pty) Ltd. ZipRip, is a trademark of SMA (Australia) Ltd. PostScript is a trademark of Adobe Systems Inc. Windows is a registered trademark of Microsoft Inc.
This devise complies with part 15 of the FCC Rules. Operation is subject to the following two conditions (1) this device may not cause harmful interference, and (2) this devise must accept any interference received, including interference that may cause undesired operation. SP25 VDE OM 2.0-1 (2006)
SAFETY INFORMATION When using your equipment, the following safety precautions should always be followed. Safety During Operation WARNING: Indicates a potentially hazardous situation which, if instructions are not followed, could result in death or serious injury. CAUTION: Indicates a potentially hazardous situation which, if in- structions are not followed, may result in minor or mod- erate injury or damage to property.
Page 7
• If the machine must be transported by vehicle, please contact your service representative. • For environmental reasons, do not dispose of the equipment or expended supply waste at household waste collection points. Disposal can take place at an authorized dealer or at appropriate collection sites. SP25 VDE OM 2.0-1 (2006)
INTRODUCTION The SeriPrinter System produces dry printed output, similar to a copier. This is as a result of it’s unique and patented fixing system. This enables the user to print on a wide variety of paper, card and certain coated stock including vinyl. The SeriPrinter is a freestanding unit which, operates in conjunction with the Ricoh family of duplicators.
MACHINE (Duplicator delivery view) Safety switch Paper collection from duplicator Docking holes and slot Paper jam pin Paper transport vacuum belts SP25VDE OM 2.0-1(2006)
OPERATION PANEL Machine status LCD Decrease Increase Manual Speed Manual Speed Manual Speed Control ON & Off Button On Button Service Buttons SP25 VDE OM 2.0-1 (2006)
WHERE TO PUT THE SERIPRINTER. Your machines’s location should be carefully chosen because environ- mental conditions greatly affect it’s performance. Environmental Conditions Optimum environmental conditions Caution • Keep the equipment away from humidity and dust. Otherwise a fire or an electric shock might occur. •...
After cooling is complete the LCD will dis- play: Lamp hours and machine status: idle. CAUTION: Do Not power OFF at the main switch or plug switch before the cooling process has completed. SP25 VDE OM 2.0-1 (2006)
BASIC OPERATION Before proceeding with operating the SeriPrinter. The following important points should be observed. 1. Installation. The SeriPrinter installation procedure must have been complete by a trained service technician using the SP25 installation manual. 2. SeriDrums. Only SeriDrums should be used in the Digital Duplicator when a SeriPrinter has been installed.
Page 15
Note: If the manual speed is set slower then the speed of the Digital Duplica- tor a paper jam will occur. Master Eject Box. The Master Eject box should be emptied once a day. Note: If this is not done the master eject box will be difficult to empty. SP25 VDE OM 2.0-1 (2006)
Page 16
4. Undocking and Docking. The SeriPrinter is physically attached to the Digital Duplicator. This is called the docking mechanism. In order to release the docking mechanism there is a button located on the rear panel of the SeriPrinter on the side where the ma- chines are docked.
• Finishing equipment needs less cleaning • Less paper cockling gives better registration • Vibrant colors • Multi pass prints double sided Accessories Scale ( 2 different) EDP Code List Special matched colors - contact the local Dealer for information. SP25 VDE OM 2.0-1 (2006)
WHAT TO DO IF SOMETHING GOES WRONG 1. Paper jam in SeriPrinter: If a paper jam occurs in the SeriPrinter the lamps and belts will switch off. The SeriPrinter Jam Pin will activate blocking paper from exiting the duplicator. The duplicator will detect that paper can not exit and will stop printing. The duplicator will show a Paper Jam error..
10. Smudging on the leading edge and corners could be due to very heavy ink coverage in these areas. To remove the smudging reduce the ink coverage or rotate the image by 180 degrees so that the heavy coverage is no longer on the leading edge. SP25 VDE OM 2.0-1 (2006)
Page 20
Dealer information For further information visit: www.seriprinter.com SP25VDE OM 2.0-1(2006)
Need help?
Do you have a question about the SP25 VDE and is the answer not in the manual?
Questions and answers