LARSON RUL-9-FR User Manual

LARSON RUL-9-FR User Manual

Rechargeable lantern

Advertisement

Larson Electronics LLC
9419 E US HWY 175, Kemp, TX 75143 - P: (800) 369-6671 - F: (903) 498-3364

INTRODUCTION

Congratulations on purchasing the revolutionary RUL-9-FR rechargeable lantern. Your RUL-9-FR lantern
has some outstanding features including lightweight (2.2lbs), high visibility, rear mounted LED taillights,
low battery LED indicator and an articulating head. As the world's lightest full-power lantern, the RUL-9-
FR redefines what professionals should expect from a lantern. With proper care and maintenance, this
portable lantern will provide long, dependable service. Please take a moment to read this instruction
sheet before using your new lantern. It provides important safety and operating instructions.
NOTICE
Before using the lantern or battery charger, read all instructions and cautionary markings on the
unit.
CAUTION:
Do not attempt to use that charger to recharge any other product. Also do not
attempt to use any other charger to recharge your lantern.
Do not operate a damaged charger. Replace damaged cords or charger immediately. Do not try
to repair a damaged lantern or charger yourself. Should your charger fail to operate for any
reason, contact our service center, Larson Electronics at 1-800-369-6671, for further
instructions.
Do not abuse the cord. Never carry the charger by the cord or disconnect the charger from a
receptacle by pulling the cord.
Unplug power adapter and remove lantern from charger before performing any routine cleaning
or maintenance.
Do not place any metal objects onto the charging terminal located in the charger.
Do not incinerate or leave the battery pack near a heat source such as a radiator, fireplace,
stove, or any other heat-generating appliance. When exposed to high temperatures, the battery
pack could explode and possibly cause a fire.
Do not disassemble or mistreat a battery pack or store a battery pack where it could come in
contact with metal objects that could short circuit the battery pack terminals. The resulting
current can cause high temperatures and damage to the battery pack and also can cause burns
and possibly fire.
Please refer to local ordinances concerning battery recycling and disposal.
Use of this product for other than a lighting device is not recommended. Manufacturer
specifically disclaims liability for other than recommended use.
The direct wire feature for this charger is intended for power sources between 12 to 24VDC.
Attempting to direct wire to any other power source will cause severe damage to the charger.
Be sure to check the AC adapter voltage rating to ensure that the required voltage and
frequency match the available power source. On the right side of the lantern is a low battery
LED indicator.
*For 4 and 6 cell lanterns, approximately 30 minutes of runtime remains when the indicator is
activated.
*For 8 cell lanterns, approximately 60 minutes of runtime remains when the indicator is
activated.
www.LarsonElectronics.com
RUL-9-FR
sales@larsonelectronics.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the RUL-9-FR and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for LARSON RUL-9-FR

  • Page 1 RUL-9-FR INTRODUCTION Congratulations on purchasing the revolutionary RUL-9-FR rechargeable lantern. Your RUL-9-FR lantern has some outstanding features including lightweight (2.2lbs), high visibility, rear mounted LED taillights, low battery LED indicator and an articulating head. As the world’s lightest full-power lantern, the RUL-9- FR redefines what professionals should expect from a lantern.
  • Page 2 Larson Electronics LLC www.LarsonElectronics.com sales@larsonelectronics.com 9419 E US HWY 175, Kemp, TX 75143 - P: (800) 369-6671 - F: (903) 498-3364 If your lantern includes a carrying strap, attach the strap to the rings using the quick connect clips provided on the strap.
  • Page 3: Lifetime Limited Warranty

    The RUL-9-FR can be charged using the supplied 120 VAC wall adapter plug or by direct wiring to a 12-24 VDC power source (not supplied). For the direct wire option, the wire and co-axial jack from the wall plug adapter can be cut off and used to make connections to the charge base.

Table of Contents