TABLE OF CONTENTS INTRODUCTION AND GENERAL INSTRUCTIONS ..........................3 INSTRUCTIONS FOR INSTALLATION..............................3 SPECIAL INSTRUCTIONS FOR USE AND MAINTENANCE........................ 3 MACHINE KEYPAD....................................4 ELECTRIC - HYDRAULIC CONNECTION ............................. 5 STARTING UP ......................................6 COFFEE, CAPPUCCINO, MILK DISPENSING............................9 SHIFT DISPENSING..................................... 11 CONTINUOUS DISPENSING WITH BUTTO N°17 ..........................
In any case, regularly check the boiler even where the water is not very hard, and if necessary, have the resistors and tubing descaled by specialised technicians. Failure to clean Macchiavalley. machines daily, especially for brewing unit and milk frother, using approved cleaning products and following specified cleaning procedure will result in void warranty and service contract.
Every time that you power ON the machine, any smart card must be removed from the slot otherwise the display will show the following error message: Card error After having connected the machine to the water and electric networks, turn the switch on (see diagram). The display shows: Macchiavalley ZZZZ ZZZ ZZZ Rev. X.XXX Where : ZZZZ ZZZ ZZZ : indicates the installation date REV.
Page 7
Press the key N°11( ON/OFF ), the display shows: Filling - up steam boiler During this stage the steam boiler is being filled up. WARNING: The solenoid valve of the steam nozzle automatically opens to release the air inside the boiler. When the steam boiler has been filled up, the display shows: Filling - up coffee boiler Press T 1...
Page 8
If the display shows: SELECT DRINK Coffee not ready The displayed message indicates that the set up heating temperature in the coffee boiler has not been reached yet, and therefore coffee based dispensing are not enabled If the display shows: SELECT DRINK Steam not ready The displayed message indicates that the set up heating temperature in the steam boiler has not been reached yet, and...
COFFEE, CAPPUCCINO, MILK DISPENSING 1) Machine configurations Standard The display shows: SELECT DRINK Place a cup under the adjustable in height coffee dispenser, and press the dose key required. The display shows: XXXXXX ¯ ¯ ¯ ¯ ¯ ¯ ¯ ¯ ¯ ¯ where “XXXXXX”...
Page 10
3) Machine configurations Self The display shows: SELECT DRINK Place a cup under the coffee dispenser and press the dose key required. The display shows: XXXXXX ¯ ¯ ¯ ¯ ¯ ¯ ¯ ¯ ¯ ¯ where “XXXXXX” indicates the selected dose key name. The cursor indicates the amount of drink being dispensed.
XXXXXX ¯ ¯ ¯ ¯ ¯ ¯ ¯ ¯ ¯ ¯ Where XXXXXXXX is the name of the selected drink. The cursor indicates the amount of drink being dispensed. WARNING: a) On-Off button is enabled only when the smart card is inserted b) When pressing the selection button before inserting coins, the display shows the cost of the selected drink.
CONTINUOUS DISPENSING WITH BUTTO N°17 The “ Continuos “ function for button N°17 is enabled only if in “Parameters machine“ the parameters “ Button 17 function ” has been programmed as Continuos. Press the key N°17 as many times as the number of doses you want to dispense, (maximum value is 9) ; the display shows: SELECT DRINK Where X indicates the number of cycles that the machine will automatically carry out for the dose you will select.
HOT WATER DISPENSING Place a cup under the hot water outlet, and press the hot water key dose n°9. Dispensing will be automatically stopped once the programmed dose is over. The display shows: HOT WATER ¯ ¯ ¯ ¯ ¯ ¯ ¯ ¯ ¯ The cursor indicates the amount of drink being dispensed.
SYSTEM CLOCK PROGRAMMING N:B: The System Clock parameters are available only with the system clock enable. To enter in System clock programming, proceed as follows. WITH SMART-CARD: Insert the Owner or Waiter smart card into the proper slit and keep pressed the key N°17 (Enter) .
AUTOMATIC RINSING CYCLE 1) Automatic group rinsing. A timed rinsing cycle of the brewing chamber is automatically carried out 15 minutes after the last dispensed drink and every 180 minutes when the machine is in stand-by mode. The display shows: GROUP AUTOCLEANING PLEASE NOTE: 5 seconds before the starting of the rinse cycle the machine will BEEP !.
ACCESS THE MAIN SETTING MENUS WITH PASSWORD OR SMART-CARD A) ACCESS THE MAIN SETTING MENUS WITH PASSWORD To enter the programming environments, a password is required which define the access rights to the different environments. The password must be composed with 5 numbers. To insert the passwords proceed as follows: Turn the machine OFF Keep N°17 “Enter”...
KEY REFERENCE FOR PASSWORD LB. 00151-00-GB Pag. 17 02/08/06...
Page 18
B) ACCESS THE MAIN SETTING MENUS WITH SMART CARD To enter the programming environments , insert one of the following smart cards into the proper slit with the machine in off: : - WAIETR SMART CARD - ROASTER- SMART CARD - OWNER SMART CARD the display shows : Select...
PROGRAMMABLE PARAMETERS IN ACCORDING WITH PASSWORD OR SMART CARDS Password or Password or Password or Smartcard Smartcard Smartcard System manager WAITER ROASTER OWNER Info - Reset Dose Data System Data Dose Slight Adj. Dose Programming Calibration Machine Parameter Language M. Configuration Serial Ground Numbers Milker...
READ AND RESET DATA To enter in Read and reset data , proceed as follows. WITH SMART-CARD: Insert the Owner smart card into the proper slit and with machine in OFF keep pressed the key N°17 (Enter) . WITH PASSWORD : Digit the Owner password . The display shows : Select Enter...
Page 21
Enter Press the + / - keys to select Reset Doses Data the count A or B. + / - Enter Reset Doses Data + / - Please confirm Enter WITH THIS OPERATION WE RESET ONLY THE DOSES COUNT – EXTRA MILK AND Reset Doses Data TOTAL CASHING Enter...
INFO SYSTEM DATA To enter in Info system data , proceed as follows. WITH SMART-CARD: Insert the Owner smart card into the proper slit and keep pressed the key N°17 (Enter) . WITH PASSWORD : Digit the Owner password . The display shows : Select Enter...
THE FOLLOWING INFO ARE DISPLAYED ONLY WHEN THE CLOCK IS PROGRAMMED Enter Water filter Water filter + / - Enter XXXX YY - ZZZZ Confirm reset Water filter Enter XXXX YY - ZZZZ XXXX : Indicates the n° of water filter liters left. If the programmed n°...
DOSES SLIGHT ADJUST PROGRAMMING PLEASE NOTE : TO ACCESS TO THE DOSES SLIGHT ADJUST THE MACHINE MUST BE AT THE SET-UP TEMPERATURE. To enter in doses slight adjust programming mode, proceed as follows. WITH SMART-CARD: Insert the Owner or Roaster smart card into the proper slit and keep pressed the key N°17 (Enter) .
SET DOSES PRICE PROGRAMMING PLEASE NOTE : TO ACCESS TO THE SET DOSES PRICE THE MACHINE MUST BE AT THE SET -UP TEMPERATURE. To enter in Set doses price programming mode, proceed as follows. WITH SMART-CARD: Insert the Owner smart card into the proper slit and keep pressed the key N°17 (Enter) .
SHIFT DOSES SLIGHT ADJUST PROGRAMMING PLEASE NOTE : TO ACCESS TO THE SHIFT DOSES SLIGHT ADJUST THE MACHINE MUST BE AT THE SET -UP TEMPERATURE. By means of the Shift button, is possible to adjust other 10 doses for a total number of 20 drinks . To enter in Shift doses slight adjust programming mode, proceed as follows.
SET SHIFT DOSES PRICE PROGRAMMING PLEASE NOTE : TO ACCESS TO THE SET SHIFT DOSES PRICE THE MACHINE MU ST BE AT THE SET -UP TEMPERATURE. To enter in Set shift doses price programming mode, proceed as follows. WITH SMART-CARD: Insert the Owner smart card into the proper slit and keep pressed the key N°17...
AUTOMATIC CLEANING OF COFFEE GROUP Keep ( N° “17” key ) Press “T1” key to start Open the machine door pressed for five seconds the cleaning cycle SELECT CLEANING SELECT CLEANING GROUP CLEANING OPEN FRONT PANEL AND CLEAN GROUP Clean the group filters by Clean the front door from Clean the group from any means of a cloth and close the...
ONLY IN CASE THAT AFTER THE AUTOMATIC CLEANING PROCESS THE MILK FROTHER IS NOT PROPERLY DISPENSING, CARRY OUT A MANUAL CLEANING ( SEE THE FOLLOWING PAGE ). FOR CLEANING OPERATIONS, MACCHIAVALLEY STRONGLY RECOMMEND TO USE THE FOLLOWING DETERGENT PRODUCTS: CLEANING TABLETS MILK FROTHER CLEANER 100 Tablets ( 1.2gr.) Code N°...
MANUAL CLEANING OF MILK FROTHER AND COFFEE OUTLET Remove the cover from the Remove the milk frother Remove the screw that fix coffee outlet and the coffee outlet from its the cover of the coffee outlet holder Reassemble the milk frother as indicated in Disassemble milk Disassemble the...
MANUAL CLEANING OF BARISTA STEAM Leave Barista steam into Clean the Barista steam by Unscrew the external tube hot water for 5 minutes. means of a cloth. of the Barista steam Clean the air hole of the Clean the internal tube by Screw the external tube of Barista steam.
MACHINE FUNCTIONS MESSAGES 1) Full grounds bin alarm. Grounds Bin Full Cause: grounds bin full. The number of coffee grounds in the bin has reached the value set in the programming phas e. Result: shutdown of the coffee based dispensing keys. Solution: remove the grounds bin and empty it, replace the bin when the display shows: Have you inserted the Grounds Bin ?
Page 33
Solution: press the ( Clean/Deca ) N°17 key to reset the alarm and put decaffeinated into the decaf door. PLEASE NOTE: In case of other message, please, contact a MACCHIAVALLEY Spa. Authorised Service Centre 8) Message of coffee boiler heating temperature not reached.
Page 34
The MACCHIAVALLEY S.p.A. product you have purchased is subject to Directive 2002/96/EC of the European Parliament and the Council of the European Union on waste electrical and electronic equipment (WEEE) and, in jurisdictions adopting that Directive, is marked as being put on the market after August 13, 2005, and should not be disposed of as unsorted municipal waste.