Astralpool 1800 Series Installation And Operating Instructions Manual
  1. Manuals
  2. Brands
  3. Astralpool Manuals
  4. Swimming Pool Pump
  5. 1800 Series
  6. Installation and operating instructions manual

Astralpool 1800 Series Installation And Operating Instructions Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Milenium Sand Filter System
Installation Instructions

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 1800 Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Astralpool 1800 Series

Summary of Contents for Astralpool 1800 Series

  • Page 1 Milenium Sand Filter System Installation Instructions...

  • Page 3: Electrical Data

    Introduction: INSIDE: Winterizing Your Filter System.......13 Setting Up your Equipment......4-6 Water Maintenance..........14 Plumbing The System To Your Pool....7 Starting Your System........8-9 Filter System Parts Breakdown....14-15 Troubleshooting.........16-17 Cleaning The Pump Strainer......10-11 Manufacturer’s Warranty.........18 Cleaning The Filter ........12 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ Warns about hazard that CAN cause serious personal injury and property damage if ignored.

  • Page 4: Contents Of Carton

    What you should have: Contents of carton: Code Description Code Description 24181-0100 Filter body 22503-0050 Pressure gauge set 720R1750057 O-ring 170x5, 75 00555R0401 Tee adapter 24182-1003 Plastic V-clamp set 074065008A Air releif plug 22358 Selector valve / Multiport 00470R0319N Gasket 24182-0007 Flange 24mm 24181-0004 Water drain set 22503-0017 Filter collector / Standpipe...

  • Page 5: Setting Up Your System

    Setting up your system: Step 1 Remove fi lter, pump and base from the carton. Remove filter, pump and base from the carton. Using (2) bolts and washers, mount pump Using (2) 1/4 x 20 bolts and washers, mount pump to base.
  • Page 6 Setting up your system: 150 Lbs. of sand. Be sure the standpipe assembly remains centered while pouring the sand. Now remove the standpipe cover and place the diverter on top of the fi lter basket. DIAL VALVE INSTALLATION: Carefully remove all sand DIAL VALVE INSTALLATION: Carefully remove all sand particles from the mounting location, being especially particles from the mounting location, being especially...
  • Page 7 Setting up your system: If your system is supplied with a backwash adapter: Remove threaded adapter and tape from the hardware kit. Prepare backwash fi ttings by wrapping threads kit. Prepare backwash fittings by wrapping threads with tefl on tape in a clockwise rotation, four to eight with teflon tape in a clockwise rotation, four to eight wraps is usually suffi...
  • Page 8 Typical system -to-pool plumbing connection: Install four barbed adapters (B) using tefl on tape in the following lacations:...

  • Page 9: System Startup

    System startup:...

  • Page 11: Cleaning The Pump Strainer

    Cleaning the pump strainer: Press down on the dial valve handle and rotate to WINTERIZE, release the handle. This action will allow air into the tank and prevent excessive back-flow through the strainer. Unscrew and remove the clear strainer cover.
  • Page 12 Cleaning the pump strainer: Replace the clear strainer cover.
  • Page 13 Backwashing (cleaning) the filter: Set dial valve to BACKWASH. Start pump. Observe water flow in sight glass and when clear (usually 2-3 minutes) stop pump. Set valve to RINSE, run for 20-30 seconds. This action removes any debris trapped in the filter during backwash.
  • Page 14 Winterizing the filter system: Drain the filter tank by first removing the drain and then set dial valve to WINTERIZE. Replace the drain cap once filter is drained.
  • Page 15 Description Code Bacap strainer lid 25461-0102 Bacap basket handle 24561-0205 Bacap strainer basket 24561-0202 Union nut 02193 Drain plugs o-ring 7230130025 Drain plug 19028-0103 Description Code Bacap pump housing 25461-0203 Strainer lid O-ring 118x4 NBR 50 Sh(A) 77A1180040 Bacap pump base 25461-0502 Link fl...

  • Page 16: Parts Identification

    Parts identification: Code Description Code Description 24181-0100 Filter body 22503-0050 Pressure gauge set 720R1750057 O-ring 170x5, 75 00555R0401 Tee adapter 24182-1003 Plastic V-clamp set 074065008A Air releif plug 22358 Selector valve / Multiport 00470R0319N Gasket 24182-0007 Flange 24mm 24181-0004 Water drain set 22503-0017 Filter collector / Standpipe 24181-0006 Gasket 00638 Collector arm / Lateral...

Table of Contents