NEO M54N User Manual
  1. Manuals
  2. Brands
  3. NEO Manuals
  4. Laptop
  5. M54N
  6. User manual

NEO M54N User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Advertisement

Table of Contents
loading

Related Manuals for NEO M54N

Summary of Contents for NEO M54N

  • Page 3 Preface Notice The company reserves the right to revise this publication or to change its contents without notice. Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse) of this publication.

  • Page 4: Fcc Statement

    Preface FCC Statement (Federal Communications Commission) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

  • Page 5: Important Safety Instructions

    Preface IMPORTANT SAFETY INSTRUCTIONS Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury to persons when using any electrical equipment: Do not use this product near water, for example near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool.

  • Page 6: Instructions For Care And Operation

    Preface Instructions for Care and Operation The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions: Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged. Do not expose the computer Do not place it on an unstable Do not place anything heavy...
  • Page 7 Preface Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other strong magnetic fields. These can hinder proper performance and damage your data. Follow the proper working procedures for the computer. Shut the computer down properly and don’t forget to save your work.

  • Page 8: Power Safety

    Preface Power Safety The computer has specific power requirements: • Only use a power adapter approved for use with this computer. • Your AC/DC adapter may be designed for international travel but it still requires a steady, Power Safety uninterrupted power supply. If you are unsure of your local power specifications, consult Warning your service representative or local power company.

  • Page 9: Battery Precautions

    Preface Battery Precautions • Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer. • Do not remove any batteries from the computer while it is powered on. • Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire.

  • Page 10: Cleaning

    Preface Cleaning Do not apply cleaner directly to the computer; use a soft clean cloth. Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer. Servicing Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and the computer to electric shock.

  • Page 11: Travel Considerations

    Preface Travel Considerations Packing As you get ready for your trip, run through this list to make sure the system is ready to go: Check that the battery pack and any spares are fully charged. Power off the computer and peripherals. Close the display panel and make sure it’s latched.
  • Page 12 Preface On the Road In addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Troubleshooting, keep these points in mind: Hand-carry the notebook - For security, don’t let it out of your sight. In some areas, computer theft is very common.
  • Page 13 Preface Developing Good Work Habits Developing good work habits is important if you need to work in front of the computer for long periods of time. Improper work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or other joints.
  • Page 14 Preface Lighting Proper lighting and comfortable display viewing angle can reduce eye strain and muscle fatigue in your neck and shoulders. • Position the display to avoid glare or reflections from overhead lighting or outside sources of light. • Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly. •...

  • Page 15: Table Of Contents

    Preface Contents Notice .................I Hot-Key Buttons & Keyboard ........1-9 FCC Statement .............II Function Keys ..............1-10 Instructions for Care and Operation ......IV System Map: Front & Rear Views .......1-11 Power Safety .............. VI System Map: Left View ..........1-12 Battery Precautions ...........VII System Map: Right View ..........1-13 Cleaning ..............
  • Page 16 Preface Application Hot-Key ...........2-10 Battery Life ..............3-9 TouchPad and Buttons/Mouse ........2-11 Recharging the Battery with the AC/DC Adapter ..3-10 Configuring the TouchPad and Buttons ....2-11 Proper handling of the Battery Pack ......3-11 Audio Features .............2-12 Battery FAQ ..............3-12 8 Channel Sound Support .........2-13 Swap Battery (Optional) ..........3-13 Adding a Printer ............2-14 Drivers &...
  • Page 17 Preface Hot-Key (WinXP) ............4-10 POST Beep Sound (Advanced Menu) ......5-9 AutoMail (WinXP) ...........4-10 Security Menu ..............5-10 Bluetooth ..............4-11 Set Supervisor Password (Security Menu) ....5-10 PC Camera ..............4-11 Password on boot: (Security Menu) ......5-11 Wireless LAN ............4-11 Boot Menu ..............5-12 Port Replicator ............4-11 Exit Menu ..............5-13 BIOS Utilities Upgrading The Computer...
  • Page 18 Preface Interface (Ports & Jacks) PCIe WLAN Module ...........7-10 Intel WLAN Driver Installation .......7-11 Overview ...............A-1 Port Replicator .............7-12 Notebook Ports and Jacks ..........A-2 Port Replicator Setup Instructions: ......7-13 Built-In Microphone .............A-2 Port Replicator Serial (COM) Port Driver (WinXP) 7-13 Card Reader Port ............A-2 Port Replicator Network (LAN) Driver (WinXP) ..7-14 DC-In Jack ..............A-2...
  • Page 19 Preface Intel Video Driver Controls Specifications Intel Video Driver Installation ........B-1 Processor ............... C-2 Dynamic Video Memory Technology ......B-2 Core Logic ..............C-2 Intel Graphics Properties ..........B-3 Memory ................. C-2 Display Devices ............B-5 Security ................. C-2 Attaching Other Displays ..........
  • Page 20 Preface XVIII...

  • Page 21: Quick Start Guide

    Quick Start Guide Chapter 1: Quick Start Guide Overview This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the computer and to getting your system started. The remainder of the manual covers the following: •...

  • Page 22: Model Differences

    Quick Start Guide Model Differences This notebook series includes two different model types (each model includes two design styles). The models differ slightly in design style including the LCD type, and the location of the card reader (the easiest way to dif- ferentiate between the model types is the location of the card reader).

  • Page 23: Advanced Users

    Quick Start Guide Advanced Users If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful to refer to “What to Install” on page 4 - “BIOS Utilities” on page 5 - 1 “Upgrading The Computer”...

  • Page 24: Not Included

    Quick Start Guide Not Included Operating Systems (e.g. Windows XP) and applications (e.g. word processing, spreadsheet and database pro- grams) have their own manuals, so please consult the appropriate manuals. System Software Your computer may already come with system software pre-installed. Where this is not the case, or where you are re-configuring your computer for a different system, you will find this manual refers to the Microsoft Win- dows XP (Home &...

  • Page 25: System Startup

    Quick Start Guide System Startup Remove all packing materials. Place the computer on a stable surface. Securely attach any peripherals you want to use with the notebook (e.g. keyboard and mouse) to their ports. Attach the AC/DC adapter to the DC-In jack on the right of the computer, then plug the AC power cord into an outlet, and connect the AC power cord to the AC/DC adapter (Note: If you have included the Port Replicator in your purchase option see page 12).

  • Page 26: System Map: Model A - Top View With Lcd Panel Open

    Quick Start Guide System Map: Model A - Top View with LCD Panel Open Optional Built-In PC Camera Wireless Device LED Status Indicators Operation Aboard Hot-Key Buttons Aircraft Power Button Keyboard The use of any portable Built-In Microphone electronic transmission de- TouchPad and Buttons vices aboard aircraft is usu- ally prohibited.

  • Page 27: System Map: Model B - Top View With Lcd Panel Open

    Quick Start Guide System Map: Model B - Top View with LCD Panel Open Optional Built-In PC Camera Speakers Wireless Device LED Status Indicators Operation Aboard Hot-Key Buttons Aircraft Power Button The use of any portable Keyboard electronic transmission de- TouchPad and Buttons vices aboard aircraft is usu- LED Power &...

  • Page 28: Led Indicators

    Quick Start Guide LED Indicators Table 1 - 3 - LED Power & Communication Indicators The two sets of LED indicators (LED Status Indica- Icon Color Description tors and LED Power & Communication Indicators) Green The Computer is On on the computer display helpful information about the current status of the computer.

  • Page 29: Hot-Key Buttons & Keyboard

    Quick Start Guide Hot-Key Buttons & Keyboard The keyboard has an embedded numerical keypad for easy numeric data input, and features Function Keys to These buttons give instant access to the default Inter- allow you to change operational features instantly (see net browser and e-mail program, and to a user-defined Figure 1 - application, with one quick button press.
  • Page 30 Quick Start Guide Function Keys To use the function keys, press and hold the Fn key, then press the appropriate function key (F1 - F12 etc.). Function Function Function Key Fn + F8 Decrease LCD Brightness Fn + F1 TouchPad Toggle Fn + F9 Increase LCD Brightness Fn + F3...

  • Page 31: System Map: Front & Rear Views

    Quick Start Guide System Map: Front & Rear Views LED Power & Model A Communication Indicators LCD Latch (Model A Only) Model B 4-in-1 Card Reader (Model B Only) External Monitor Port S-Video-Out Jack Security Lock Slot Battery Figure 1 - 5 - Front & Rear Views 4-in-1 Card Reader The card reader allows you to use the most popular digital storage card formats: MMC (MultiMedia Card) / SD (Secure Digital) / MS (Memory Stick) / MS Pro (Memory Stick Pro)

  • Page 32: System Map: Left View

    Quick Start Guide System Map: Left View RJ-45 LAN Jack Model A - Left Vent/Fan Intake 2 * USB 2.0 Ports S/PDIF-Out Jack Line-In Jack Mini-IEEE 1394 Port Model B - Left ExpressCard Slot (see page 4-in-1 Card Reader (Model A Only) Figure 1 - 6 - Left View 4-in-1 Card Reader The card reader allows you to use the most popular digital storage card formats:...

  • Page 33: System Map: Right View

    Quick Start Guide System Map: Right View Figure 1 - 7 - Right View Headphone-Out Jack Microphone-In Jack USB 2.0 Port RJ-11 Phone Jack Optical Device Drive Bay (for CD/DVD Device - see page DC-In Jack Changing DVD Regional Codes Go to the Control Panel and double-click System >...

  • Page 34: System Map: Bottom View

    Quick Start Guide System Map: Bottom View Figure 1 - 8 - Bottom View Model A Vent/Fan Intake Battery Module Bay Cover The CPU is not a user ser- Hard Disk Cover viceable part. Opening this Speakers (Model A Only) compartment, or access- ing the CPU in any way, may violate your warranty.

  • Page 35: Windows Xp Start Menu & Control Panel

    Quick Start Guide Windows XP Start Menu & Control Panel Most of the control panels, utilities and programs within Windows XP (and most other Windows versions) are accessed from the Start menu. When you install programs and utilities they will be installed on your hard disk drive, and a shortcut will usually be placed in the Start menu and/or the desktop.

  • Page 36: Video Features

    Quick Start Guide Video Features Your computer has built-in Intel (Intel 945GM) video. You can switch display devices, and configure display options, from the Display Properties control panel in Windows as long as the appropriate video driver is in- stalled. For more detailed video information see “Intel Video Driver Controls”...

  • Page 37: Display & Graphics Properties

    Quick Start Guide Display & Graphics Properties Figure 1 - 10 - Display & Graphics Properties Video Features 1 - 17...

  • Page 38: Display Devices & Options

    Quick Start Guide Display Devices & Options Besides the built-in LCD, you can also use an external VGA monitor (CRT)/external Flat Panel Display or TV as your display device. A VGA monitor/Flat Panel Display connects to the external monitor port, a TV to the S-Video-Out jack.

  • Page 39: Power Management Features

    Quick Start Guide Power Management Features The Power Options control panel icon in Windows (see page 15) allows you to configure power management features for your computer. You may conserve power through individual components such as the monitor or hard disk (by means of Power Schemes), or you may use either Stand by or Hibernate mode to conserve power throughout the system (enable Hibernate support from the control panel as pictured in Figure 1 -...
  • Page 40 Quick Start Guide 1 - 20...

  • Page 41: Features & Components

    Features & Components Chapter 2: Features & Components Overview Read this chapter to learn more about the following main features and components of the computer: • Hard Disk Drive • Optical (CD/DVD) Device • 4-in-1 Card Reader • ExpressCard Slot •...

  • Page 42: Hard Disk Drive

    Features & Components Hard Disk Drive The hard disk drive is used to store your data in the computer. The hard disk can be Power Safety taken out to accommodate other 2.5" serial (SATA) hard disk drives with a height of 9.5 mm.

  • Page 43: Optical (Cd/Dvd) Device

    Features & Components Optical (CD/DVD) Device There is a bay for a 5.25" optical (CD/DVD) device (12.7mm height). The actual de- Sound Volume vice will depend on the module you purchased (see “Storage” on page C - 3). The Adjustment optical device is usually labeled “Drive D:”...

  • Page 44: Handling Cds Or Dvds

    Features & Components Handling CDs or DVDs Proper handling of your CDs/DVDs will prevent them from being damaged. Please follow the advice below to make sure that the data stored on your CDs/DVDs can be CD Emergency Eject accessed. If you need to manually eject a CD (e.g.

  • Page 45: Dvd Regional Codes

    Features & Components DVD Regional Codes To change the DVD regional codes see “Changing DVD Regional Codes” on page 1 - DVD Regional Coding Table 2 - 1 Region Geographical Location DVD Regional Coding USA, Canada Western Europe, Japan, South Africa, Middle East &...

  • Page 46: 4-In-1 Card Reader

    Features & Components 4-in-1 Card Reader The card reader allows you to use some of the latest digital storage cards. Push the Card Reader Cover card into the slot and it will appear as a removable device, and can be accessed in the same way as your hard disk (s).

  • Page 47: Expresscard Slot

    Features & Components ExpressCard Slot The computer is equipped with an ExpressCard/34/54 slot that reads Express Card/ ExpressCard Slot 34 and ExpressCard/54 formats. ExpressCards are the successors to PCMCIA (PC Cover Cards). Make sure you keep the ExpressCard/54 is used for applications which require a larger interface slot, e.g. cover in the Express- CompactFlash card reader.

  • Page 48: Auto Mail Checker

    Features & Components Auto Mail Checker After you have installed the driver for the Auto Mail Checker program (see “Auto- Mail (WinXP)” on page 4 - 10) you may then configure it to give you notification when you receive new mail. You must be online to receive this notification (note that this program only supports the POP3 protocol), and your default mail program does not need to be open.
  • Page 49 Features & Components You may then configure the options for your mailserver, name, password, program and method(s) of notification. Note Check with your Internet Service Provider, net- work administrator or Mail Service provider for details on what to put on these pages.

  • Page 50: Application Hot-Key

    Features & Components Application Hot-Key The hot-key buttons give instant access to the default Internet browser and e-mail Application.exe program, and to a user-defined application, with one quick button press. To config- ure a program to open when the application hot-key is pressed (Windows Me- You will need to locate dia Player is the default program), follow the instructions below.

  • Page 51: Touchpad And Buttons/Mouse

    Features & Components TouchPad and Buttons/Mouse The TouchPad is an alternative to the mouse; however, you can also add a mouse to Mouse Driver your computer through one of the USB ports. The TouchPad buttons function in much the same way as a two-button mouse. The central button may be configured to If you are using an exter- function as you require.

  • Page 52: Audio Features

    Features & Components Audio Features You can configure the audio options on your computer from the Sounds and Audio Sound Volume Devices Windows control panel, or from the Realtek HD Audio Manager Adjustment icon in the taskbar/control panel (this will bring up the Realtek Audio Configuration menus).

  • Page 53: Channel Sound Support

    Features & Components 8 Channel Sound Support If you wish to configure your system for 8 channel sound support, then the following ports should be used as outputs. Double-click the appropriate icon (e.g. ) to bring up the “Connected device:” dialog box to configure the output port. •...

  • Page 54: Adding A Printer

    Features & Components Adding a Printer The most commonly used peripheral is a printer. The following conventions will Parallel Printer help you to add a printer, however it is always best to refer to the printer manual for specific instructions and configuration options. After setting up the print- er attach the parallel ca- ble to the printer.

  • Page 55: Power Management

    Power Management Chapter 3: Power Management OS Note Overview Power management To conserve power, especially when using the battery, your computer uses the ACPI functions will vary power management system. Power management conserves power by controlling in- slightly depending on dividual components of the computer (the monitor and hard disk drive) or the whole your operating system.

  • Page 56: The Power Sources

    Power Management The Power Sources The computer can be powered by either an AC/DC adapter or a battery pack. Port Replicator AC/DC Adapter AC/DC Adapter You will be provided Use only the AC/DC adapter that comes with your computer. The wrong type of AC/ with AC/DC DC adapter will damage the computer and its components.

  • Page 57: Turning On The Computer

    Power Management Turning on the Computer Now you are ready to begin using your computer. To turn it on simply press the pow- Shutdown er button on the front panel. Note that you should al- When the computer is on, you can use the power button as a Stand by/Hibernate/ ways shut your comput- er down by choosing the Shutdown hot-key button when it is pressed for less than 4 seconds (pressing and...

  • Page 58: Power Schemes

    Power Management Power Schemes You can set your computer to conserve power through individual components by Resuming means of Power Schemes. You can also adjust the settings for each scheme to set Operation the monitor to turn off after a specified time, and the computer's hard disk motor to turn off if the hard disk drive has not been accessed for a specified period of time (if Press Sleep/Re-...
  • Page 59 Power Management Each Windows Power Scheme will also adjust the processor performance of your machine in order to save power. This is worth bearing in mind if you are experienc- ing any reduced performance (especially under DC/battery power). Choose the Home/Office Desk scheme for maximum performance when the com- puter is powered from an AC power source.

  • Page 60: System Power Options

    Power Management System Power Options You can use the system power options to stop the computer’s operation and restart where you left off. This system features Stand by and Hibernate sleep mode levels (Hibernate mode will need to be enabled by clicking the option in the Hibernate tab in the Power Options control panel - see “Hibernate”...

  • Page 61: Stand By

    Power Management Stand by Stand by saves the least amount of power, but takes the shortest time to return to full operation. During Stand by the hard disk is turned off, and the CPU is made to idle System Resume at its slowest speed.

  • Page 62: Configuring The Power Button

    Power Management Configuring the Power Button The power button may be set to send the computer in to either Stand by or Hiber- Sleep Button nate mode. In Stand by mode, the LED will blink green. In Hibernate mode the LED will be off (battery) or orange (AC/DC adapter). If you are in a power sav- You may also configure ing mode set to save power through individual components (e.g.

  • Page 63: Battery Information

    Power Management Battery Information Please follow these simple guidelines to get the best use out of your battery. Low Battery New Battery Warning Always completely discharge, then fully charge, a new battery (see “Battery FAQ” When the battery is criti- on page 3 - 12 for instructions on how to do this).

  • Page 64: Recharging The Battery With The Ac/Dc Adapter

    Power Management Battery life may be shortened through improper maintenance. To optimize the life and improve its performance, fully discharge and recharge the battery at least once every 30 days. Conserving Battery Power We recommend that you do not remove the battery yourself. If you do need to re- move the battery for any reason see “Removing the Battery”...

  • Page 65: Proper Handling Of The Battery Pack

    Power Management Proper handling of the Battery Pack • DO NOT disassemble the battery pack under any circumstances • DO NOT expose the battery to fire or high temperatures, it may explode • DO NOT connect the metal terminals (+, -) to each other Damaged Battery Warning Should you notice any physical defects (e.g.

  • Page 66: Battery Faq

    Power Management Battery FAQ How do I completely discharge the battery? Use the computer with battery power until it shuts down due to a low battery. Don’t Caution turn off the computer by yourself even when you see a message that indicates the Danger of explosion if battery is critically low, just let the computer use up all of the battery power and shut battery is incorrectly re-...

  • Page 67: Swap Battery (Optional)

    Power Management Swap Battery (Optional) If you have included the optional swap battery in your purchase option it will allow *Swap Battery you to change batteries on your computer without having to shut the computer down. Indicator The swap battery’s total operational time is approximately three minutes; however the swap battery life is dependent upon many factors (see sidebar).
  • Page 68 Power Management 3 - 14...

  • Page 69: Drivers & Utilities

    Drivers & Utilities Chapter 4: Drivers & Utilities What to Install This chapter deals with installing the drivers and utili- ties essential to the operation or improvement of some The Device Drivers & Utilities + User’s Manual CD- of the computer’s subsystems. The system takes ad- ROM contains the drivers and utilities necessary for vantage of some newer hardware components for the proper operation of the computer.
  • Page 70 Drivers & Utilities Navigate (Browse..) to D: You will notice that many of the instructions for driver installation require you to “Navigate (Browse) to D:”. We assume that you will install all drivers and utilities from the built-in CD device and it is assigned to “Drive D:”.

  • Page 71: Service Packs

    Drivers & Utilities Service Packs Check the warnings on the following pages regarding installation of the appropriate Service Pack for your Windows XP Service Pack 2 Windows OS. Make sure you have installed the appro- priate Service Pack before installing all the drivers. Make sure you install Windows XP Service Pack 2 (or a Windows XP version which includes Service Pack 2) before installing any drivers.

  • Page 72: Authorized Driver Message

    Drivers & Utilities Authorized Driver Message Updating/Reinstalling Individual Drivers If you receive a message telling you that the driver you If you wish to update/reinstall individual drivers it are installing is not authorized (Digital Signature Not may be necessary to uninstall the original driver.To do Found), just click Yes or Continue Anyway to ignore this go to the Control Panel in the Windows OS and the message and continue the installation procedure.

  • Page 73: Driver Installation

    Drivers & Utilities Driver Installation Check the driver installation order from Table 4 - 1, on page 4 - 6 (the drivers must be installed in Insert the Device Drivers & Utilities + User’s Manual this order) which is the same as that listed in the CD-ROM and click Install WinXP Drivers (button).

  • Page 74: New Hardware Found

    Drivers & Utilities New Hardware Found WinXP SP2 Driver Page # If you see the message “New Hardware Found” (Found New Hardware Wizard) during the installa- Install the appropriate Service Pack for WinXP Page 4 - 3 tion procedure (other than when outlined in the driver Chipset Page 4 - 7 install procedure), click Cancel to close the window,...

  • Page 75: Winxp Driver Installation Procedure

    Drivers & Utilities WinXP Driver Installation Procedure Video (WinXP) This section covers driver and utility installation in- 1. Click 2.Install Video Driver > Yes from the structions for Windows XP Home & Professional. In- Drivers Installer menu. sert the Device Drivers & Utilities + User’s Manual CD-ROM, click Install WinXP Drivers (button) and Navigate (Browse..) to then click the appropriate driver name from the Driv-...

  • Page 76: Lan (Winxp)

    Drivers & Utilities LAN (WinXP) Modem (WinXP) 1. Click 4.Install LAN Driver > Yes from the 1. Click 5.Install Modem Driver > Yes from the Drivers Installer menu. Drivers Installer menu. Click Start (menu) > Run... and navigate Click Start (menu) > Run... and navigate (Browse...) to D:\Drivers\LAN\Setup.exe and (Browse...) to click OK.

  • Page 77: Touchpad (Winxp)

    Drivers & Utilities TouchPad (WinXP) ExpressCard/Card Reader (WinXP) 1. Click 6.Install TouchPad Driver > Yes from 1. Click 7.Install Express Card Driver > Yes the Drivers Installer menu. from the Drivers Installer menu. Click Start (menu) > Run... and navigate Click Start (menu) >...

  • Page 78: Hot-Key (Winxp)

    Drivers & Utilities Hot-Key (WinXP) AutoMail (WinXP) 1. Click 8.Install Hotkey Utility > Yes from the The AutoMail Driver must be installed manually as per the instructions below: Drivers Installer menu. 1. Click Start (menu) > Run... and navigate Click Start (menu) > Run... and navigate (Browse..) to (Browse..) to D:\Drivers\AUTOMAIL\SETUP.EXE and...

  • Page 79: Bluetooth

    Drivers & Utilities Bluetooth Wireless LAN See install procedure in “Bluetooth Module” on See the introduction in “PCIe WLAN Module” on page 7 - page 7 - 10, and check the installation procedure. PC Camera Port Replicator See install procedure in “PC Camera Driver Installa- See install procedure in “Port Replicator Serial...
  • Page 80 Drivers & Utilities 4 - 12...

  • Page 81: Bios Utilities

    BIOS Utilities Chapter 5: BIOS Utilities Overview BIOS Settings Warning This chapter gives a brief introduction to the computer’s built-in software: Incorrect settings can cause your system to Diagnostics: The POST (Power-On Self Test) malfunction. To correct mistakes, return to Set- up and restore the Set- Configuration: The Setup utility up Defaults with <F9>.

  • Page 82: The Power-On Self Test (Post)

    BIOS Utilities The Power-On Self Test (POST) Each time you turn on the computer, the system takes a few seconds to conduct a POST Screen POST, including a quick test of the on-board RAM (memory). 1.BIOS information As the POST proceeds, the computer will tell you if there is anything wrong. If there 2.CPU type is a problem that prevents the system from booting, it will display a system summary 3.Memory status...

  • Page 83: Failing The Post

    BIOS Utilities Failing the POST Errors can be detected during the POST. There are two categories, “fatal” and “non- fatal”. Fatal Errors These stop the boot process and usually indicate there is something seriously wrong with your system. Take the computer to your service representative or authorized service center as soon as possible.

  • Page 84: The Setup Program

    BIOS Utilities The Setup Program The Phoenix Setup program tells the system how to configure itself and manage ba- sic features and subsystems (e.g. port configuration). Entering Setup To enter Setup, turn on the computer and press F2 during the POST. The prompt (Press F2 to Enter Setup) seen on page 5 - 2 is usually present for a few seconds...

  • Page 85: Setup Screens

    BIOS Utilities Setup Screens The following pages contain additional advice on portions of the Setup. Setup Menus Along the top of the screen is a menu bar with five (5) menu headings. When you Setup menus select a heading, a new screen appears. Scroll through the features listed on each shown in this section are screen to make changes to Setup.

  • Page 86: Main Menu

    BIOS Utilities Main Menu PhoenixBIOS Setup Utility Figure 5 - 2 Main Main Advanced Security Boot Exit Main Menu Item Specific Help System Time: [22:11:05] System Date: [01/09/2006] IDE Channel 0 Master [CD-ROM] <Tab>, <Shift Tab>, or SATA Port 1 [60012MB SATA1] <Enter>...

  • Page 87: Ide Channel 0 Master/Sata Port 1 (Main Menu)

    BIOS Utilities IDE Channel 0 Master/SATA Port 1 (Main Menu) Pressing Enter opens the sub-menu to show the configuration of either a CD Device or HDD on the computer’s IDE Channel 0/SATA port 1. Use the Auto (Type:) set- ting to have the items configured automatically for you. System/Extended Memory (Main Menu) This item contains information on the system memory, and is not user configurable.

  • Page 88: Advanced Menu

    BIOS Utilities Advanced Menu Figure 5 - 3 PhoenixBIOS Setup Utility Advanced Menu Main Advanced Advanced Security Boot Exit Item Specific Help Installed O/S: [WinXP] Select the operating Reset Configuration Data: [No] system installed on your system which Legacy USB Support: [Enabled] you will use most Boot-time Diagnostic Screen:...

  • Page 89: Reset Configuration Data (Advanced Menu)

    BIOS Utilities Reset Configuration Data (Advanced Menu) This item is set to No as default. You can change the setting to Yes if you have in- stalled a new add-on which has reconfigured the system, resulting in such a serious system conflict that the operating system is unable to boot.

  • Page 90: Security Menu

    BIOS Utilities Security Menu Figure 5 - 4 PhoenixBIOS Setup Utility Security Menu Main Advanced Security Boot Exit Item Specific Help Set Supervisor Password [E E nter] Password on boot: [Disabled] Supervisor Password Fixed disk boot sector: [Enter] controls access to the setup utility.

  • Page 91: Password On Boot: (Security Menu)

    BIOS Utilities Password on boot: (Security Menu) Specify whether or not a password should be entered to boot the computer. If “En- abled” is selected, only users who enter a correct password can boot the system (see Password Warning the warning in the sidebar). The default setting is “Disabled”. If you set a boot pass- word (Password on boot Note: To clear existing passwords press Enter and type the existing password, then...

  • Page 92: Boot Menu

    BIOS Utilities Boot Menu Figure 5 - 5 PhoenixBIOS Setup Utility Boot Menu Main Advanced Security Boot Exit Item Specific Help Boot priority order: USB FDC: Keys used to view or USB HDD: configure devices: IDE CD: PIONEER DVD-RW DVR-K16RA- Up and Down arrows USB CDROM: select a device.

  • Page 93: Exit Menu

    BIOS Utilities Exit Menu Figure 5 - 6 PhoenixBIOS Setup Utility Exit Menu Main Advanced Security Boot Exit Item Specific Help Exit Saving Changes Exit Discarding Changes Exit System Setup and Load Setup Defaults save your changes to Discard Changes CMOS.
  • Page 94 BIOS Utilities 5 - 14...

  • Page 95: Upgrading The Computer

    Upgrading The Computer Chapter 6: Upgrading The Computer Overview This chapter contains information on upgrading the computer. Follow the steps out- lined to make the desired upgrades. If you have any trouble or problems you can con- Warranty Warning tact your service representative for further help. Before you begin you will need: Please check with your service representative...

  • Page 96: When Not To Upgrade

    Upgrading The Computer When Not to Upgrade These procedures involve opening the system’s case, adding and sometimes replac- ing parts. Power Safety Warning You should not perform any of these upgrades if: Before you undertake upgrade proce- • Your system is still under warranty or a service contract dures, make sure that •...

  • Page 97: Removing The Battery

    Upgrading The Computer Removing the Battery If you are confident in undertaking upgrade procedures yourself, for safety reasons Warranty Warning it is best to remove the battery. Turn the computer off, and turn it over. Please check with your service representative Slide the latch in the direction of the arrow, and hold it in place.
  • Page 98 Upgrading The Computer Lift the battery out in the direction of the arrow Figure 6 - 2 Battery Up Lift the battery out. Figure 6 - 3 Battery Out 6 - 4 Removing the Battery...

  • Page 99: Upgrading The Hard Disk Drive

    Upgrading The Computer Upgrading the Hard Disk Drive The hard disk drive can be taken out to accommodate other 2.5" serial (SATA) hard HDD System disk drives with a height of 9.5mm (h) (see “Storage” on page C - 3). Follow your Warning operating system’s installation instructions, and install all necessary drivers and util- ities (as outlined in...
  • Page 100 Upgrading The Computer For Model A computers (see overleaf for Model B): Slide the hard disk and cover assembly in the direction of arrow Lift the hard disk and cover assembly up in the direction of arrow Remove the hard disk and cover assembly Remove the 4 screws to release the hard disk from the assembly cover, and reverse the process to install any new hard disk.
  • Page 101 Upgrading The Computer For Model B computers: Pull the tab to slide the hard disk and case assembly in the direction of arrow Lift the hard disk and case assembly out of the bay in the direction of arrow Remove screws to release the hard disk from the case , and...

  • Page 102: Upgrading The Optical (Cd/Dvd) Device

    Upgrading The Computer Upgrading the Optical (CD/DVD) Device Turn off the computer, and turn it over and remove the battery. Locate the module bay cover and remove screws (Model A)/ (Model B). Remove the bay cover Use a screwdriver to carefully push out the optical device at point Reverse the process to install the new device.

  • Page 103: Upgrading The System Memory (Ram)

    Upgrading The Computer Upgrading the System Memory (RAM) The computer has two memory sockets for 200 pin Small Outline Dual In-line (SO- DIMM) DDRII (DDR2) type memory modules (see “Memory” on page C - 2 details of supported module types). The total memory size is automatically detected by the POST routine once you turn on your computer.
  • Page 104 Upgrading The Computer Remove the bay cover Figure 6 - 9 RAM Cover Removed Contact Warning Be careful not to touch Gently pull the two release latches on the sides of the memory socket in the the metal pins on the direction indicated by the arrows ( &...
  • Page 105 Upgrading The Computer The RAM module will pop-up, and you can remove it. Figure 6 - 11 RAM Removal Pull the latches to release the second module if necessary. Insert a new module holding it at about a 30° angle and fit the connectors firmly into the memory slot.

  • Page 106: Upgrading The Processor

    Upgrading The Computer Upgrading the Processor If you want to upgrade your computer by replacing the existing processor with a fast- Warranty er/new one you will need to contact your customer service representative. We rec- ommend that you do not do this yourself, since if it is done incorrectly you may The CPU is not a user damage the processor or mainboard.

  • Page 107: Modules & Options

    Modules & Options Chapter 7: Modules & Options Wireless Device Overview Operation Aboard This chapter contains information on the following modules, which may come with Aircraft your computer, depending on the configuration purchased. If you are unsure please The use of any portable contact your service representative.

  • Page 108: Bluetooth Module

    Modules & Options Bluetooth Module Before installing the Bluetooth driver, make sure that the optional Bluetooth mod- Wireless Device ule is on (the LED will be orange). Use the Fn + F12 key combination (see Operation Aboard “Function Keys” on page 1 - 10) to toggle power to the Bluetooth module.
  • Page 109 Modules & Options User Guide View BlueSoleil User Guides from the Help Menu (or press the F1 key) in the IVT Cor- poration BlueSoleil - Main Window control panel. Click BlueSoleil User Guides in the Contents tab, and click to select the appropriate User Guide from the panel on the right.

  • Page 110: Pc Camera

    Modules & Options PC Camera Before installing the PC Camera driver, make sure that the optional PC Camera is Taking Still Pictures on. Use the Fn + F10 key combination (see “Function Keys” on page 1 - 10) to toggle power to the PC Camera module. Make sure you install the drivers in the Double-click order indicated in Table 4 - 1, on page 4 -...

  • Page 111: Pc Camera Driver Installation

    Modules & Options PC Camera Driver Installation 1. Press the Fn + F10 key combination to power on the PC Camera module (click Cancel if you see a “New Hardware Found” message) . 2. Make sure the module is powered on, and then insert the Device Drivers & Utilities + User’s Manual CD-ROM into the CD/DVD drive.

  • Page 112: Pc Camera Audio Setup

    Modules & Options PC Camera Audio Setup If you wish to capture video & audio with your camera, it is necessary to setup the audio recording options in Windows. Go to the Start menu and point to Settings (or just click Control Panel) and click Control Panel, then double-click the Sounds &...
  • Page 113 Modules & Options Figure 7 - 2 Audio Setup (Windows XP) PC Camera 7 - 7...

  • Page 114: Bisoncap

    Modules & Options BisonCap BisonCap is a video viewer useful for general purpose video viewing and testing, and can capture video files to .avi format. Pre-Allocating File Space Run the BisonCap program from the Start > Programs/All Programs > Bison- You may pre-allocate Cam menu (it is recommended that you set the capture file before the capture the file size for the cap-...

  • Page 115: Eliminating Screen Flicker

    Modules & Options Eliminating Screen Flicker If you find that the video screen in the BisonCap program is flickering, you can try to adjust the setting in the Video Capture Filter options. Run the BisonCap program. Go to Options and scroll down to select “Video Capture Filter...”. Click either 50Hz or 60Hz under Frequency in Property Page (tab).

  • Page 116: Pcie Wlan Module

    Modules & Options PCIe WLAN Module If you have included an Intel PRO/Wireless 3945ABG (802.11a/b/g) PCIe WLAN Wireless Device module in your purchase option, you will have the appropriate software CD provid- Operation Aboard ed for your module. Aircraft The use of any portable Before installing the Intel 3945ABG (802.11a/b/g) PCIe WLAN driver, make sure electronic transmission de- that the Wireless LAN module is on (the...

  • Page 117: Intel Wlan Driver Installation

    Modules & Options Intel WLAN Driver Installation 1. Make sure the module is powered on, and then insert the Device Drivers & Utilities + User’s Manual CD-ROM into the CD/DVD drive. User Guide 2. Click Install WinXP Drivers (button). Insert the Device Driv- 3.

  • Page 118: Port Replicator

    Modules & Options Port Replicator If you have included the Port Replicator in your purchase option, the device will al- Port Replicator low you to easily attach the notebook to standard, non-portable devices e.g. a printer AC/DC Adapter or monitor. Note the sidebar warning on the power supply. You will be provided with AC/DC...

  • Page 119: Port Replicator Setup Instructions

    Modules & Options Port Replicator Setup Instructions: Turn the computer OFF. Attach the Port Replicator’s external monitor cable to the external monitor port on the rear of the computer. Attach the Port Replicator’s power cable to the DC-In jack on the right of the computer.

  • Page 120: Port Replicator Network (Lan) Driver (Winxp)

    Modules & Options Port Replicator Network (LAN) Driver (WinXP) 1. Attach the Port Replicator as per the instructions in “Port Replicator” on page 7 - 12 2. Insert the provided Port Replicator CD into the computer’s CD/DVD drive. 3. If you can see the My Computer icon on the desktop (if you cannot see the My Computer icon go to step 4) click on it once to select it, then right- click it to make the sub-menu appear and scroll down to Properties and click on it (go to step 5).

  • Page 121: Troubleshooting

    Troubleshooting Chapter 8: Troubleshooting Overview Should you have any problems with your computer, before consulting your service representative, you may want to try to solve the problem yourself. This chapter lists some common problems and their possible solutions. This can’t anticipate every problem, but you should check here before you panic. If you don’t find the answer in these pages, make sure you have followed the instructions carefully and observed the safety precautions in the preface.

  • Page 122: Basic Hints And Tips

    Troubleshooting Basic Hints and Tips Many of the following may seem obvious but they are often the solution to a problem when your computer ap- pears not to be working. • Power - Is the computer actually plugged into a working electrical outlet? If plugged into a power strip, make sure it is actually working.

  • Page 123: Backup And General Maintenance

    Troubleshooting Backup and General Maintenance • Always backup your important data, and keep copies of your OS and programs safe, but close to hand. Don’t forget to note the serial numbers if you are storing them out of their original cases, e.g. in a CD wal- let.

  • Page 124: Viruses

    Troubleshooting Viruses • Install an Anti-Virus program and keep the definitions file (the file which tells your program which viruses to look for) up to date. New computer viruses are discovered daily, and some of them may seriously harm your computer and cause you to lose data. Anti-Virus programs are commercially available and the defini- tions file updates are usually downloadable directly from the internet.

  • Page 125: Upgrading And Adding New Hardware/Software

    Troubleshooting Upgrading and Adding New Hardware/Software • Do not be tempted to make changes to your Windows Registry unless you are very sure of what you are doing, otherwise you will risk severely damaging your system. • Don’t open your computer or undertake any repair or upgrade work if you are not comfortable with what you are doing.
  • Page 126 Troubleshooting • Thoroughly check any recent changes you made to your system as these changes may affect one or more system components, or software programs. If possible, go back and undo the change you just made and see if the problem still occurs. •...

  • Page 127: Power

    Troubleshooting Power Problem Possible Cause - Solution You turned on the power Battery missing / incorrectly installed. Check the battery bay, make sure the battery is present and but it doesn’t work. seated properly (the design of the battery only allows it to go in one way). Make sure there’s nothing interfering with the battery contacts.
  • Page 128 Troubleshooting Problem Possible Cause - Solution The computer feels too Make sure the computer is properly ventilated and the Vent/Fan intakes are not blocked. If this hot. doesn’t cool it down, put the system into Hibernate mode or turn it off for an hour. Make sure the computer isn’t sitting on a thermal surface (see “Overheating”...

  • Page 129: Display

    Troubleshooting Display Problem Possible Cause - Solution Nothing appears The system is in a power saving mode. Toggle the Fn + F4 (see “Sleep Button” on page 3 - screen. sleep/resume key combination. The screen controls need to be adjusted. Toggle the screen control key combinations Fn + F8/F9. If you’re connected to an external monitor, make sure it’s plugged in and turned on.

  • Page 130: Boot Password

    Troubleshooting Boot Password Problem Possible Cause - Solution forget boot If you forget the password, you may have to discharge the battery of the CMOS. Contact your password. service representative for help. Password Warning If you choose to set a boot password, NEVER forget your password. The consequences of this could be serious. If you cannot remember your boot password you must contact your vendor and you may lose all of the information on your hard disk.

  • Page 131: Audio & Cd Device

    Troubleshooting Audio & CD Device Problem Possible Cause - Solution The sound cannot be The volume might be set too low. Check the volume control in the Volume Control Panel in the heard or the volume is Windows taskbar, or use the key combination Fn + F5 and F6 (see “Audio Features”...

  • Page 132: Keyboard

    Troubleshooting Keyboard Problem Possible Cause - Solution Unwelcome numbers If the LED is lit, then Num Lock is turned ON. (see “LED Indicators” on page 1 - appear when typing. Other Keyboards If your keyboard is damaged or you just want to make a change, you can use any standard USB keyboard. The system will detect and enable it automatically.

  • Page 133: Operation

    Troubleshooting Operation Problem Possible Cause - Solution The system freezes or The system’s power saving features have timed-out. Use the AC/DC adapter, press the sleep (Fn the screen goes dark. + F4) key combination, or press the power button if no LEDs are lit. The system never goes Power Options features are not enabled.

  • Page 134: Modules

    Troubleshooting Modules Problem Possible Cause - Solution Wireless LAN/ The modules are off. Check the LED indicator to see if the WLAN/Bluetooth module is on or Bluetooth modules off (see “LED Indicators” on page 1 - 8). If the LED indicator is off, then press the Fn + F11 cannot be detected.

  • Page 135: Interface (Ports & Jacks)

    Interface (Ports & Jacks) Appendix A: Interface (Ports & Jacks) Overview The following chapter will give a quick description of the interface (ports & jacks) which allow your computer to communicate with external devices, connect to the internet etc. Interface (Ports & Jacks) A - 1...

  • Page 136: Notebook Ports And Jacks

    Interface (Ports & Jacks) Notebook Ports and Jacks Item Description Built-In Microphone The built-in microphone allows you to record on your computer Card Reader Port The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device.

  • Page 137: Microphone-In Jack

    Interface (Ports & Jacks) Item Description Microphone-In Jack Plug an external microphone in to this jack to record on your computer. Mini-IEEE 1394 Port This port allows a high-speed connection to various peripheral devices, e.g. external disk drives and digital cameras (see note below). Mini-IEEE 1394 Port The Mini-IEEE 1394 port only supports SELF POWERED IEEE 1394 devices.

  • Page 138: S/Pdif-Out Jack

    Interface (Ports & Jacks) Item Description S/PDIF-Out Jack This S/PDIF (Sony/Philips Digital Interface Format) Out Jack allows you to connect your DVD- capable PC to a Dolby AC-3 compatible receiver for “5.1” or ‘dts’ surround sound. S-Video-Out Jack Connect your television to your computer and view DVDs, VCDs or anything else your computer can display.

  • Page 139: Usb 2.0/1.1 Ports

    Interface (Ports & Jacks) Optional Port Replicator Ports and Jacks Item Description DC-In Jack Plug the supplied AC/DC adapter into this jack to power your computer. External Monitor (VGA) Port This port allows you to connect an external monitor, or Flat Panel Display, to get dual video or simultaneous display on the LCD and external monitor/FPD (see “Display Devices”...
  • Page 140 Interface (Ports & Jacks) A - 6...

  • Page 141: Intel Video Driver Controls

    Intel Video Driver Controls Appendix B: Intel Video Driver Controls The basic settings for configuring the LCD are outlined in “Video Features” on page 1 - Intel Video Driver Installation Make sure you install all the drivers in the order indicated in Table 4 - 1, on page 4 6.

  • Page 142: Dynamic Video Memory Technology

    Intel Video Driver Controls Dynamic Video Memory Technology ® Intel DVMT 3.0 automatically and dynamically allocates as much (up to 128MB) DVMT Notes system memory (RAM) as needed to the video system (the video driver must be installed - see page 1).

  • Page 143: Intel Graphics Properties

    Intel Video Driver Controls Intel Graphics Properties More advanced video configuration options are provided by the Intel(R) Graphics Taskbar Icon Media Accelerator Driver for Mobile control panel. You can also access the Open Display Properties > Settings > Advanced (see page 16).
  • Page 144 Intel Video Driver Controls You may make changes to the devices, color, schemes, Hot Keys etc. by clicking the appropriate menu item or button. Click Information (button) to obtain useful in- formation about the graphics properties of the computer, and see the Support tab in Help Menus Information to get weblinks to the latest information on the Intel Website.

  • Page 145: Display Devices

    Intel Video Driver Controls Display Devices Besides the built-in LCD, you can also use an external monitor/flat panel display or Function Key TV as your display device. The following are the display options: Combination The built-in LCD. You can use the Fn + F7 An external monitor connected to the external monitor port.

  • Page 146: Attaching Other Displays

    Intel Video Driver Controls Attaching Other Displays If you prefer to use a monitor or flat panel display, connect it to the external monitor Intel Display Note port at the rear of the computer. Note that the notebook Attach your external monitor to the external monitor port (or TV to the S-Video-Out is the default Primary jack), and turn it on.

  • Page 147: Display Modes

    Intel Video Driver Controls Display Modes Single Display Only one of your attached displays is used. Twin This mode will drive multiple displays with the same content and resolutions, color quality etc. (does not support a TV as a display device). See “Twin Mode Support”...
  • Page 148 Intel Video Driver Controls To Enable Intel(R) Dual Display Clone Mode OR Twin Mode Attach your external monitor to the external monitor port (or TV to the S-Video-Out jack), and turn it on. Twin Mode Support Go to the Graphics Properties control panel (see “Intel Graphics Properties”...
  • Page 149 Intel Video Driver Controls To Enable Extended Desktop Mode: Attach your external monitor to the external monitor port (or TV to the S-Video-Out jack), and turn it on. Display Settings Go to the Graphics Properties control panel (see “Intel Graphics Properties” Extended Desktop on page B - 3) and click Display Devices.
  • Page 150 Intel Video Driver Controls To Enable Extended Desktop (Display Properties) Attach your external monitor to the external monitor port (or TV to the S-Video-Out jack), and turn it on. Display Settings Click Start, point to Settings (or click Control Panel) and click Control Panel (if Extended Desktop you are in Category View choose Appearance and Themes).

  • Page 151: Tv Settings

    Intel Video Driver Controls TV Settings If you are using a TV as a display device adjust the display settings as follows: Function Key Attach your TV to the S-Video-Out jack and turn it on. Combination Go to the Graphics Properties control panel (see “Intel Graphics Properties”...
  • Page 152 Intel Video Driver Controls B - 12...

  • Page 153: Specifications

    Specifications Appendix C: Specifications Latest Specification Information The specifications listed in this Appendix are correct at the time of going to press. Certain items (particularly processor types/ speeds and CD/DVD device types) may be changed or updated due to the manufacturer's release schedule. Check with your service center for details.

  • Page 154: Processor

    Specifications Feature Specification Processor Intel® Core™ Duo Processor 65nm (65 Nanometer) Process Technology (478-pin) Micro-FC-PGA Package 2MB On-die L2 Cache & 667MHz FSB T2300/ T2400/ T2500/ T2600/ T2700 1.66/ 1.83/ 2.0/ 2.16/ 2.33 GHz Intel® Core™ Solo Processor 65nm (65 Nanometer) Process Technology (478-pin) Micro-FC-PGA Package 2MB On-die L2 Cache &...

  • Page 155: Video Adapter

    Specifications Feature Specification Video Adapter Intel 945GM Integration Supports Dynamic Video Memory Technology DVMT 3.0 - Up to 128MB of Video Memory (dynamically allocated from system memory where needed) Supports Analog Monitor Pixel Resolution up to 1600 * 1200 at 85Hz Supports DirectX 9 Storage One Changeable 12.7mm(h) Optical Device (CD/DVD) Type Drive (see...

  • Page 156: Interface

    Specifications Feature Specification Interface Three USB 2.0 Ports One RJ-11 Jack for Plug & Play Fax/Modem One External Monitor Port One RJ-45 Jack for 10Mb/ 100Mb/ 1000Mb Fast One Headphone-Out Jack Ethernet One Microphone-In Jack One Mini-IEEE 1394 Port One Line-In Jack One S-Video-Out Jack (supports HDTV) One S/PDIF Output Jack One DC-in Jack...

  • Page 157: Power

    Specifications Feature Specification Power Full Range AC/DC Adapter 20V, 3.25A (65 Watts), 100~240V, 47~63Hz Full Range AC/DC Adapter 20V, 4.5A (90 Watts), 100~240V, 47~63Hz (If Using the Optional Port Replicator) 6 Cell Smart Lithium-Ion Battery Pack, 4000mAH (44.4W) 6 Cell Smart Lithium-Ion Battery Pack, 4400mAH (48.8W) Environmental Temperature Relative Humidity...
  • Page 158 Specifications C - 6...

Table of Contents