Description four-wheel, tandem axle, heavy-duty trailer with adjustable hitch for large engine-driven welding generators (20 pages)
Summary of Contents for Miller Electric HWY-210
Page 1
189 553 OM-699 February 1998 Description Two-Wheel Trailer For Small Engine- Driven Welding Generators HWY-210 & OFR-210 Visit our website at www.MillerWelds.com...
Page 2
ISO 9001 Quality service information for your particular model System Standard. are also provided. Miller Electric manufactures a full line of welders and welding related equipment. For information on other quality Miller products, contact your local Miller distributor to receive the latest full line catalog or individual catalog sheets.
Page 3
TRAILER TOWING SAFETY PRECAUTIONS WARNING In trailer towing, as in most driving situations, exposure to certain hazards occurs. Trailer towing is safe when precautions are taken. The following safety information is only a summary of the more complete information found in the Safety Standards listed at the end of these precautions.
Page 4
Couplers Clevis Lunette Ball Side Marker Lights Torquing Sequence Wheel Bearings Nuts Inside Hub Self-Actuating Hydraulic Brake System Breakaway Cable Surge-Type Coupler Bracket safety_trailer 10/96 INCORRECT SIZE OR RATING OF HITCH can cause trailer to break loose from towing vehicle. 1.
Drive, Warrendale, PA 15096-0001. REPORTING SAFETY DEFECTS involved in individual problems between you, your dealer, or MILLER Electric Mfg. Co. To contact NHTSA, you may either call the Auto Safety Hotline toll-free at 1-800-424-9393 (or 366-0123 in Washington, D.C. area) or write to: NHTSA, Washington D.C.
SECTION 1 − ASSEMBLY SAFETY PRECAUTIONS 1-1. Symbol Usage Means Warning! Watch Out! There are possible hazards with this procedure! The possible hazards are shown in the adjoining symbols. Y Marks a special safety message. Means “Note”; not safety related. 1-2.
SECTION 3 − ASSEMBLY NOTE All directions are given as facing the towing vehicle. The word “front” means the hitch end of the trailer. 3-1. Assembling Trailer Y Use adequate blocks or lifting device to support frame while installing parts. Shackle Arm Spring Attach shackle arms to springs using 9/16...
Page 10
3-2. Installing Hitch And Safety Chains Tools Needed: 9/16, 3/4 in 11/16, 3/4 in Y Use adequate blocks or lifting de- vice to support frame while instal- ling parts. Y Support trailer with jack. Block wheels. Wheel Block Block wheels. Safety Chain Chain Bracket OM-699 Page 4...
Page 11
3-3. Installing Optional Light Kit Wiring Connections: Right Stop/ Signal Lamps (Green) Left Stop/ To Vehicle Signal Lamps (Yellow) Taillights (Brown) Ground (White) White Ground Lead (Ground To Trailer Frame) Y Support trailer with jack. Block wheels. Wiring Harness White Ground Lead Secure ground lead ring terminal to the chain bracket using 1/4-20 x 3/4 hardware.
3-4. Installing Wiring Harness Tab Connectors NOTE Disconnect vehicle wiring harness plug from trailer wiring connector before beginning installation. Use wiring harness tab connectors only with insulated wires. 3-5. Installing Welding Generator Tools Needed: 9/16 in OM-699 Page 6 Connector Run Wire Tap Wire Place unstripped run wire in slotted...
3-6. Maintenance NOTE Do not use trailer if any part is damaged or not working properly. When performing maintenance, check trailer for worn, damaged, or non-working parts. Check for free rotation of assemblies mounted on bushings or bearings. Tools Needed: 13/16, 1-1/8 in Y Support trailer with jack.
3-7. Torquing Wheel Bearings 0.01 in (0.2 mm) endplay maximum Check hub endplay. If loose, remove wheel and go to next step. Torque to 12 ft lb (16 N·m) Torque nut while turning hub forward. Y Do not loosen nut more than 1/8 turn in this step.
Page 19
LIMITED WARRANTY − Subject to the terms and conditions below, Miller Electric Mfg. Co., Appleton, Wisconsin, warrants to its original retail purchaser that new Miller equipment sold after the effective date of this limited warranty is free of defects in material and workmanship at the time it is shipped by Miller.
Page 20
Parts) Circuit Diagrams Welding Process Handbooks File a claim for loss or damage during shipment. 1998 Miller Electric Mfg. Co. 9/98 Miller Electric Mfg. Co. An Illinois Tool Works Company 1635 West Spencer Street Appleton, WI 54914 USA International Headquarters−USA USA Phone: 920-735-4505 Auto-Attended USA &...
Need help?
Do you have a question about the HWY-210 and is the answer not in the manual?
Questions and answers