USER MANUAL Preface Thank you for purchasing the TK106 GPS vehicle tracker. This manual shows how to operate the device smoothly and correctly. Make sure to read this manual carefully before using this product. Please note that specification and information are subject to changes without prior notice in this manual. Any change will be integrated in the latest release.
8 Command ---------------------------------------------------------------------- 1 Summary function Working Based on existing GSM/GPRS network and GPS satellites, this product can locate and monitor any remote targets by SMS or GPRS. 1.1 Positioning and Tracking: Through the on-line Positioning Platform or the cell phone to locates at times, and get the working status.
4 Specs. Content Specs. Dim. 85mm x 63mm x 25mm(3.3*2.5*0.98) Weight 160g Network GSM/GPRS/GPS Band 850/1800/1900Mhz or 900/1800/1900Mhz or 850/900/1800/1900 GPS chip SIRF3 chip GSM/GPRS Simcom300 or Simcom340 module GPS sensitivity -159dBm GPS accuracy Cold status 45s Time To First Fix Warm status 35s Hot status 1s Work voltage...
Page 6
5.2 GPS Vehicle Tracker Installation GPS/GSM/GPRS tracker should be installed by technical professional of local service centre. Without permission, the user cant repair and move the tracker randomly. If users do, any unfortunate damage should be compensated by himself. 5.2.1 Install Wire Box 5.2.2 GPS Vehicle Tracker Installation...
Installation steps (caution: the following installation should under no power, otherwise will be dangerous) Wire for cutting off circuit of the tracker Wire for cutting off oil of the tracker White wire connects relay feet 86; 85 feet Yellow wire connects the relay feet 86; 85 to 12 V DC anode, 87 feet and 30 feet are in feet to 12 V DC anode, 87 feet and 30 feet in series in the supply power circuits.
Remark: Make sure the new password is in 6 digits, or else the tracker can not recognize the password. 5.5.2 you can Send "resumepassword" to the tracker, to restore the original setting in case of losing the new password. Remark: Please remember the new password, because most of the instruction need the password to set 5.6 Authorization There are only 5 numbers able to be authorized.
5.9 Remote control oil and circuit 5.9.1 Control oil Send SMS "stopoil+password" to control oil. For example send SMS:stopoil123456 To supply the oil again, send SMS "supplyoil+password" to the unit. 5.9.2 Control circuit Send SMS "stopelec+password" to control circuit. For example send SMS: stopelec123456 To supply the circuit again, send SMS "supplyelec+password"...
5.13.1 Set up: Send SMS "speed+password+ space +080" to the unit (suppose the speed is 80km/h), and it will reply "speed ok!". When the target moves exceeding 80 km/h, the unit will send SMS "speed+080!+Geo-info" to the authorized numbers. It will alarm one time in each setting. 5.13.2 Cancel: Send SMS to deactivate the overspeed alert nospeed+password...
commands. 5.19.1 Set an IP address and port: The IP address and port of Communication Protocol in the tracker can be modified and transferred data to other platform. Send SMS "ip +ip address+port +port number" to the unit. If the tracker s IP address and port number should be modified to 116.255.131.50and 8500, send SMS "ip116.255.131.50port8500"to the tracker.
Page 12
Location report in Dont use it in the place beyond reach of signals. Place the unit outdoors, especially when starting it up. digits of zeros. 8 Command FUNCTION SMSREPLY CHAP Intialition begin123456 begin ok Change password Change password password123456 666888 5.5.1 resume Resume password...
Page 13
2.The first using ,please put the device to the outdoor which have the power GPS signal ,then begin to track after two minitues. 3.The English capital letter and lower-case represent the command , English capital letter is the setting content ,please using lower case to edit all commands by telephone.
Need help?
Do you have a question about the TK106 and is the answer not in the manual?
Questions and answers