Table of Contents
Summary of Contents for JCM TSP-01
- Page 1 Office: (800) 683-7248 Technical Support: (702) 651-3444 FAX: (702) 651-0214 E-Mail: techsupport@jcm-american.com Web-Site: www.jcm-american.com Thermal Printer Series - 100 JCM part No. 960-000038 2002 JCM – American, Corp.
-
Page 2: Table Of Contents
Illustrated Parts Breakdown ....................20 Parts List ..........................21 JCM and the JCM logo are registered trademarks of Japan Cash Machine Co., Ltd. and JCM American Corpo- ration. All other marks in this publication are registered trademarks of their respective owners. -
Page 3: Introduction
Introduction The Thermal Security Printer – TSP-01 • No complex paper loading procedures The TSP-01 is a multi-purpose printer that is such as found with rolled or fanfold suitable for any application requiring quality paper. printing ability. JCM provides the thermal paper specifica- •... -
Page 4: Model Classification
500 notes (5) Paper size 65 mm x 156 mm (US $) (6) Faceplate No Faceplate (7) Type of Software ID-003 JCM Standard ID-024 IGT Netplex (8) Other Options 001 – Standard configuration Examples: TSP-01-05-310-03-001 Printer model 01 with no front bracket, small rear style mounting, 003 ribbon style cable; 250 note capacity;... -
Page 5: General Specifications
Recommended Thermal Paper Part No. KF50 - HDA or compatible NOTE: Using other paper may affect the quality and thermal printer head longevity. Contact your JCM account repesentative for a list of qualified suppliers. Paper Dimensions 66 mm Width 156 mm Length... - Page 6 General Specifications: Cont’d Paper Rejection Function - . R.A.W - Read After Write When sensors detect double paper, or a barcode print failure condition, the paper is sent to an internal reject area and an error code is sent to the host application. The reject area has a capacity of 5 sheets.
-
Page 7: Dip Switch Settings
Dip Switch Settings Dip Switches Normal Operating Setting - This is the default setting for normal communication via the host application. Dip Switch #1: Off = Barcode check On = No barcode check Others are default to OFF position Coupon Print Test - Will print a ticket and check the barcode. If there is something wrong with the barcode, VOID will be printed on the ticket and it will be transported to the reject area. -
Page 8: Thermal Paper Specifications
Thermal Paper Specifications 1. Overview This specification is for thermally coated tickets designed for use with the JCM TSP-01 thermal printer. 2. General Characteristics 2.1 Tickets to be pre-cut sheets. 2.2 Ticket edges must be smooth to prevent double feeding. - Page 9 Paper Curl The deformation (curl and warp) of papers used for TSP-01 printers is limited as follows. Deformation to be measured after paper has been stabilized for a minimum of 48 hours at 20 ± 5 C, 55 ± 15% RH.
- Page 10 6.2 It is recommended that non-thermal side printing be pre-approved by JCM American Corp. prior to use to ensure no negative impacts on print or printer reliability. 7. Packaging 7.1 Paper shall be packaged in cartons or boxes designed to protect tickets from damage.
-
Page 11: Photo Of Printer
Paper Positioning Guide Positioning Sensor and Double Page Sensor Positioning Barcode Sensor and Sensor Doubler Paper Sensor Positioning Sensor Exit Sensor Positioning Sensor & Double Page Sensor... -
Page 12: Pin Outs
Pin Outs (ID-003) Green edge of ribbon FUNCTION SIGNAL RS-232CTXD RS-232CRXD LED POWER (24V) RCTR24 LED GND RS-232 GND DC24VDC DC24VDC PGND PGND * N/C = Not Connected... -
Page 13: Installation
Installation 1. Install the printer mount- ing frame in the host machine using the appro- priate mounting holes in the bottom of the frame. 2. Attach the ribbon cable to the host machine. 3. Slide the printer into the frame by pushing in on the arm covering the EPROM. -
Page 14: Operation
Operation Loading the Paper 1. Fan the pre-cut paper before placing it in the hopper. 2. Lift the spring-loaded pressure plate. 3. Place the paper stack in the hopper with the printed side down. 4. Release the pressure plate. NOTE: The hopper will hold 200 sheets of pre-cut paper unless the hopper extension has been added. - Page 15 Figure 3. 9. Place the black calibration paper (Part No. 501-000044) in the same position. 10. Close the printer head. 11. Move Dip switch No. 4 to OFF (see Fig. 4) 12. The LED flashes 100 ms ON, 1 sec. OFF (see Fig. 3). Figure 4 13.
-
Page 16: Troubleshooting
Troubleshooting When the printer receives a message from the host, it moves a single piece of paper from the hopper into the printer and prints the barcode information. The piece of paper is moved into another section where it is read to confirm accuracy. If there is an error condition, it moves the paper to the reject area, informs the host there was a problem, and waits further instructions. - Page 17 Troubleshooting (Cont.) It may become necessary to increase the printer contrast if the host receives a contrast error message. Use a small flat- head screwdriver to adjust the contrast control wheel (lower numbers increase contrast). Make minor adjustments, then test the printer to verify the results. To replace the EPROM, it is necessary to remove the four (4) screws securing the side of the printer.
- Page 18 Troubleshooting (Cont.) Problem Possible Cause Possible Solution No power 1. Ribbon cable not seated Check ribbon connector at the rear properly of the printer 2. Printer is not all the way Make sure the printer is all the way in the frame in the frame Printer reject Double paper sensed...
-
Page 19: Cleaning
Cleaning To clean the TSP-01 remove all paper from the hopper and use compressed air to blow out any residue. Concentrate on the rollers and the sensors. Open the head and use com- pressed air to remove any debris from the area. Then use... -
Page 20: System Logic Diagram
System Logic Diagram... - Page 21 System Logic Diagram (Cont.)
-
Page 22: Illustrated Parts Breakdown
Illustrated Parts Breakdown... -
Page 23: Parts List
PARTS LIST Part No. Description Qty. 071874 0667PT0110B Side Cover (R) 071875 0667PT0111B Side Cover (L) 071846 0667BU0101A Slide Guide Bush 025205 M3X5 Bind (Fe CR) 071872 0667PT0108B Harness Guide (L) 074078 0667KS0106 Paper pusher spring 073770 0667PT0125A Paper pusher (B2) 072277 0667PT0120C Paper pusher (A) - Page 24 Part No. Description Qty. 071884 0667CS0101 Tension roller spring 071913 0667RE0105 Spring stopper 071921 0667RE0113B Upper guide 071920 0667RE0112 Reject lever 071836 0667SH0107 Lock shaft 071881 0667TS0102 Lever spring 071880 0667TS0101 Lock spring 071761 3140-05-04A Sensor (B) harness 071900 0667PE0103B CPU Board seat 071768 667-3140-06-0...
- Page 25 Part No. Description Qty. 071903 0667GE0102 Idol gear (A) 071905 0667GE0106 Idol gear (B) 071918 0667RE0110A Lower guide (C) 071863 0667SH0104 Pinch roller lever F 071890 0667KS0103 Pinch roller SP(B)R 071891 0667KS0104 Pinch roller SP(B)L 071848 667-3140-06-04A Refractive sensor 052524 0943RE0130A Bush (LED) 071869...
- Page 26 925 Pilot Road, Las Vegas, Nevada 89119 Office: (800) 683-7248, Tech. Support: (702) 651-3444, FAX: (702) 651-0214 E-mail: techsupport@jcm-american.com http://www.jcm-american.com...
Need help?
Do you have a question about the TSP-01 and is the answer not in the manual?
Questions and answers