Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for GWC HE3130
Summary of Contents for GWC HE3130
- Page 1 USB 3.0 3-port Hub With Gigabit Ethernet Adapter User’s Manual...
-
Page 2: About This Manual
ABOUT THIS MANUAL This manual is designed for use with the USB 3.0 3 Port Hub with Gigabit Ethernet Adapter. Information in this document has been carefully checked for accuracy; however, no guarantee is given to the correctness of the contents. The information in this document is subject to change without notice. -
Page 3: Table Of Contents
Table of Contents 1. Introduction ..................4 Features ...................... 5 Package Contents ..................5 System Requirements ................. 6 2. Installation ..................7 Hardware Connection ................7 Driver Installation ..................8 ® ® ® ® On Windows XP/ Windows Vista/ Windows 7 / Windows 8 .. -
Page 4: Introduction
1. Introduction USB 3.0 3-Port hub with Gigabit Ethernet adapter is compliant with USB2.0 specification. It is two applications in the product. You can be through USB interface to access USB 3.0 Hub and Giga Ethernet at the same time. Stylish design and slim type make you easy hand carry. -
Page 5: Features
Features USB3.0 Giga Lan with 3 ports USB 3.0 HUB Small design make users easy hand carry. Support wake-on-lan function Support Green Ethernet Support IEEE 802.3az(Energy Efficient Ethernet) Support IPV4/IPV6 pack Checksum Offload Engine(COE) to reduce CPU loading Support USB 3 ports hub with BC1.2 compatible. ®... -
Page 6: System Requirements
System Requirements PC with RJ-45 and USB port. Laptop with RJ-45 and USB port. ® ® One of the following operation systems: Windows XP, Windows Vista, ® ® ® Windows 7, Windows 8 & Mac OS 10.6-10.8... -
Page 7: Installation
2. Installation Hardware Connection General instructions for installing the USB 3.0 3-port Hub with Gigabit Ethernet adapter are provided below. Since the design of system may vary, refer to your system’s reference manual for further information, if needed. -
Page 8: Driver Installation
Driver Installation ® ® ® On Windows XP/ Windows Vista/ Windows ® Windows Caution: DO NOT connect the Ethernet adapter to your computer before you install the provided driver. You will be instructed to do so later. 1. Insert the provided CD into your disc drive. Then locate and double-click the setup.exe file under x:\Driver\Windows where x is your disc drive letter. -
Page 9: On Mac Osx V10.6-10.8
3. Click Finish to complete Ethernet Driver. Now the installation is completed. You can connect the adapter to a network device by an Ethernet cable: 1. Connect an Ethernet cable to the Ethernet port on the adapter. 2. Connect the other end of the Ethernet cable to your network hub, switch or router. - Page 10 2. When the Install AX88179/178A USB Ethernet Adapter Driver screen appears, please select Continue. 3. When the screen below appears, please click Install to install...
- Page 11 4. When the screen below appears, please click Continue Installation 5. Please enter your password as prompted.
- Page 12 6. It will take for a while to install the driver. 7. The installation was successful, click Restart to restart your computer...
-
Page 13: Verifying The Driver Installation
Verifying the Driver Installation ® ® ® On Windows XP/ Windows Vista/ Windows ® Windows Once you finished the installation, you can open Windows Device Manager to verify if your Ethernet adapter is properly installed. To access the Device Manager: ®... -
Page 14: On Mac Osx V10.6-10.8
® ® ® ® On Mac OS X v10.6-10.8 To verify the driver of the adapter, follow the below steps to open the ® About this Mac on Mac When the screen below appears and click More Info… When the screen below appears, please click System Report…... - Page 15 You will find that a new Ethernet network interface is available. It’s usually named USB 3.0 Hub AX88179. *Actual strings depend on your operation system. These screen shots are from Mac OS X v10.8 and might vary slightly for each operation system. Now the installation is completed.
-
Page 16: Specifications
3. Specifications Upstream port x 1 (USB Type A plug) Downstream port x 3 (USB Type A receptacles) Compliance: USB3.0 RJ-45 x 1 (Ethernet 10/100/1000M Gigabit) Complies with the Full-duplex with flow control and Half-duplex with backpressure operation Input : 100~240V, 50Hz-60Hz Power Supply Output: 5V/2.5A (option) Green and Yellow LED for Ethernet Connection indication... -
Page 17: Regulatory Compliance
4. Regulatory Compliance FCC Conditions This equipment has been tested and found to comply with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference (2) This device must accept any interference received. Including interference that may cause undesired operation.
Need help?
Do you have a question about the HE3130 and is the answer not in the manual?
Questions and answers