Summary of Contents for Böning AHD 880 TC
- Page 1 2012-08-27 8.8“ Touchscreen Colour Display AHD 880 TC Operation Manual Read this manual before beginning any work! Dok-ID: PaB-1144 V5...
- Page 2 © Böning Automationstechnologie GmbH & Co. KG Am Steenöver 4 D-27777 Ganderkesee Tel.: +49 (0) 4221 9475-0 Fax: +49 (0) 4221 9475-21 /-22 E-Mail: info@boening.com Internet: www.boening.com...
-
Page 3: Table Of Contents
Dimensions ..............20 4.4.1 Device Dimensions Color Display AHD 880 TC ..........20 4.4.2 Panel Cutout and Drill Holes AHD 880 TC ... 21 4.4.3 Device Dimensions Remote Control AHD 650R ............ 22 4.4.4 Panel Cutout and Drill Holes AHD 650R ..23 Connections .............. - Page 4 8.8“ Touchscreen Colour Display AHD 880 TC Transport Inspection ............33 Packaging ..............33 Installation and Initial Startup ..........35 Safety ................35 Installation ..............36 Initial Startup ..............38 Operation ................39 Startup ................40 Key Functions ..............40 Measuring Point Pages ..........42 7.3.1 General Information ........42 7.3.2 Graphic Measuring Points Page with Round Instruments and Digital Displays ..42...
- Page 5 8.8“ Touchscreen Colour Display AHD 880 TC General Information Change History for Operation Manual AHD 880 TC Page / Date Version Reason for Change Author Chapter Mar 7, 2011 AHD 880 TC_Doku_de_V01_20110307 Revision of operation n.a. Biebricher, Andre manual based on an...
-
Page 6: General Information
8.8“ Touchscreen Colour Display AHD 880 TC General Information 1 General Information About this Manual Read this manual carefully before beginning any work! It is part of the product and must be kept in the product’s immedi- ate vicinity, so that it is always available to the personnel. -
Page 7: Limitation Of Liability
8.8“ Touchscreen Colour Display AHD 880 TC General Information CAUTION! … indicates a potentially hazardous situation that can result in minor or light injury, if not avoided. CAUTION! … indicates a potentially hazardous situation that can result in property damage, if not avoided. -
Page 8: Copyright
8.8“ Touchscreen Colour Display AHD 880 TC General Information Copyright This operation manual is a confidential document. It is intended solely for those persons working with the product. It is not permit- ted to hand this manual over to third parties without the manufac- turer’s prior written permission. -
Page 9: Safety
8.8“ Touchscreen Colour Display AHD 880 TC Safety 2 Safety This chapter provides an overview of all important safety aspects for optimal protection of the personnel as well as safe and error- free operation. Noncompliance with the handling and safety instructions listed in this manual can cause significant hazards. -
Page 10: Unauthorized Persons
8.8“ Touchscreen Colour Display AHD 880 TC Safety This manual lists the following qualifications for various areas of activity. Trained Person has been trained by the operator through an orientation for the assigned tasks and has been informed about possible hazards from improper execution. -
Page 11: Intended Use
The 8.8” Color Display AHD 880 TC has been exclusively designed and constructed for the purpose described in this manual. The 8.8” Color Display AHD 880 TC is a compact and versatile display unit used in alarm systems on board ships and in indus- trial plants in alarm and monitoring systems. -
Page 12: Design And Function
Fig.: 8.8“ Color Display with Touchscreen AHD 880 TC The Color Display AHD 880 TC is connected to the other compo- nents of the ship’s alarm and system, such as Data Station AHD- SAS 15, via a CAN-bus, and graphically displays their sensor data and alarm information in case of threshold violation on various dis- play pages. - Page 13 On the configuration page, the user can set the display options for the Color Display AHD 880 TC according to his own needs. He can set the system language for the screen texts, select the unit sys- tem (metric or Imperial), and the internal clock time.
- Page 14 8.8“ Touchscreen Colour Display AHD 880 TC Design and Function Fig.: Configuration diagram of a ship alarm and monitoring sys- tem and engine alarm system, dual engine configuration...
- Page 15 AHD device family communicating via CAN-bus that can han- dle numerous on board monitoring and control tasks. These sys- tem data are also visualized on the AHD 880 TC display. Among other things, the system can display the following ship...
-
Page 16: Mechanical Structure
8.8“ Touchscreen Colour Display AHD 880 TC Design and Function Mechanical Structure The 8.8” Color Display’s compact design makes it suitable for con- sole or switchboard installation. 2 LEDs and 1 photo element are integrated into the device front next to the transflective TFT-display and touch surface. -
Page 17: Technical Information
8.8“ Touchscreen Colour Display AHD 880 TC Technical Information 4 Technical Information Technical Data Color Display AHD 880 TC Description Value/Unit/Type General Data Installation type console installation Dimensions, W x H x D 270 x 130 x 77.3 mm Panel cutout, W x H... - Page 18 8.8“ Touchscreen Colour Display AHD 880 TC Technical Information Description Value/Unit/Type Interfaces Interfaces 3 x CAN-Bus 1 x RS232 (e.g. for GPS) 1 x plug, 8-pin, for Remote Con- trol AHD 650R 1 x Video In (composite video, PAL 50 Hz)
-
Page 19: Technical Data Remote Control Ahd 650R
IP 55 (rear) Electrical Data Power supply 12/24VDC (+30%/-25%) Name Plate AHD 880 TC The 8.8“ Color Display AHD 880 TC’s name plate is located on the device rear and contain the fol- lowing information: model designation of the unit ... -
Page 20: Dimensions
8.8“ Touchscreen Colour Display AHD 880 TC Technical Information Dimensions 4.4.1 Device Dimensions Color Display AHD 880 TC Fig.: Device dimensions AHD 880 TC... -
Page 21: Panel Cutout And Drill Holes Ahd 880 Tc
8.8“ Touchscreen Colour Display AHD 880 TC Technical Information 4.4.2 Panel Cutout and Drill Holes AHD 880 TC Fig.: Panel cutout and drill holes AHD 880 TC... -
Page 22: Device Dimensions Remote Control Ahd 650R
8.8“ Touchscreen Colour Display AHD 880 TC Technical Information 4.4.3 Device Dimensions Remote Control AHD 650R Fig.: Device dimensions Remote Control AHD 650R... -
Page 23: Panel Cutout And Drill Holes Ahd 650R
8.8“ Touchscreen Colour Display AHD 880 TC Technical Information 4.4.4 Panel Cutout and Drill Holes AHD 650R Fig.: Panel cutout and drill holes AHD 650R... -
Page 24: Connections
As far as the color display’s serial interfaces are concerned: the Color Display AHD 880 TC is a terminal device. This means that a 1:1 cable must be used (not a twisted wire, null modem cable or lap link). -
Page 25: Terminal Assignment
8.8“ Touchscreen Colour Display AHD 880 TC Technical Information 4.5.2 Terminal Assignment Fig.: Terminal assignment... -
Page 26: Can-Connections
To connect motor displays, e.g. to transmit motor data to the AHD TC 880. CAN connection 2 (CAN 2): To integrate the AHD 880 TC into the ship alarm system. No other CAN networks may be connected to this terminal. 4.5.4 DIP-Switch Functions Under the protective cap on the device rear, a group of DIP switches (SW 1 /1-12) is located. - Page 27 8.8“ Touchscreen Colour Display AHD 880 TC Technical Information The following table explains the DIP-switches and their corre- sponding functions. The switches marked “Customer Specific Configuration” or “Not Relevant” only serve device internal purposes and may not be changed. The switches marked “Free” have no function.
- Page 28 8.8“ Touchscreen Colour Display AHD 880 TC Technical Information Switch Function SW1-1 The device is equipped with switch-on protection (3 second delay). This function can be deactivated with this switch, i.e. the display powers on immediately after the touch surface has been touched.
-
Page 29: Cable Configuration
AHD651 Software Update TIP! The configuration instruction AHD651 Software Update is valid for both the displays AHD 880 TC and AHD 651. This document is part of the delivery. TIP! For a configuration of the display the DIP switch SW 1-12 must be set to ON (refer to page 26). -
Page 30: Graphics Configuration
Technical Information 4.6.2 Graphics Configuration For the transmission of a new graphics configuration to the display AHD 880 TC a special cable is required. The cable is connected to the GPS connector on the rear side of the device. For best data transmission the length of the cable should not ex- ceed 3 meters. -
Page 31: Upload Of Firmware And Graphics Configuration
8.8“ Touchscreen Colour Display AHD 880 TC Technical Information 4.6.3 Upload of Firmware and graphics configuration For the transmission of new firmware to the display AHD 880 TC a special cable is required. With this cable the graphics configuration can also be transmitted to the device. - Page 32 8.8“ Touchscreen Colour Display AHD 880 TC Technical Information 4.6.4 Configuration with Software Tool AHD-DeviceConfig To a limited extent the configuration of the display AHD 880 TC can be performed with the software tool AHD-DeviceConfig. The following parameters can be configured:...
-
Page 33: Transport, Packaging, And Storage
8.8“ Touchscreen Colour Display AHD 880 TC Transport, Packaging, and Storage 5 Transport, Packaging, and Storage Transport Safety Instructions Improper Transport CAUTION! Damages from improper transport! Improper transport can cause significant property damage. Therefore: – Use caution when unloading the packages dur-... - Page 34 8.8“ Touchscreen Colour Display AHD 880 TC Transport, Packaging, and Storage Handling the Packaging Materi- The packaging materials must be disposed according to current legal regulations and local ordinances. CAUTION! Environmental damages from improper dis- posal! Packaging materials are valuable raw materials and can often be reused or meaningfully processed and recycled.
-
Page 35: Installation And Initial Startup
8.8“ Touchscreen Colour Display AHD 880 TC Installation and Initial Startup 6 Installation and Initial Startup Safety Personnel Installation and initial startup may only be performed by spe- cially trained personnel. Only electricians may work on the electrical system. -
Page 36: Installation
The product is not connected to the supply voltage and switched off-circuit. Install the Color Display AHD 880 TC properly in the intended Installation installation location according to technical specifications or project drawings. Wire all inputs and outputs of the unit according to project... - Page 37 8.8“ Touchscreen Colour Display AHD 880 TC Installation and Initial Startup CAUTION! Property damage from incorrect cable connec- tions! Improperly connected cables can cause system errors and property damages. Therefore: – Always verify cable and wire designations be- fore connecting them. Check for secure seating of the connecting wires in the terminals.
-
Page 38: Initial Startup
Switch on the power supply of the Color Display AHD 880 TC and all connected external devices from the corresponding circuit breakers in the power distribution and the device inter- nal starting devices according to the corresponding operation manuals. -
Page 39: Operation
8.8“ Touchscreen Colour Display AHD 880 TC Operation 7 Operation The Color Display AHD 880 TC is generally used in ship alarm sys- tems whose components (data stations, control and display units, etc.) are connected to one another by a by a CAN bus for commu- nication and data transfer. -
Page 40: Startup
8.8“ Touchscreen Colour Display AHD 880 TC Operation Startup Start Page The Color Display AHD 880 TC is automatically powered on and begins the boot up process when the connected power supply is activated. After Startup: During the device initialization, a Start Page first appears on the... - Page 41 8.8“ Touchscreen Colour Display AHD 880 TC Operation Key for pulling up Configuration Page Key press switches the display to the configuration page for changing the basic settings. Key “Next Page” Key press switches the display to the next standard page. If no further page is available, the system display switches to the first page.
-
Page 42: Measuring Point
Measuring Point Pages 7.3.1 General Information TIP! The Color Display AHD 880 TC’s graphics and sensor data displayed on the measuring point pages can be adjusted to the individual requirements of each project. The following im- ages of the measuring point pages are therefore only for de- monstrative purposes to explain the operating functions via the device’s keys. -
Page 43: Measuring Points Page In Tabular Format
8.8“ Touchscreen Colour Display AHD 880 TC Operation Display Elements: 1 engine speed (analogue round scale instrument) 2 cooling water temperature, engine (analogue round scale instrument) 3 oil pressure, engine (analogue round scale instrument) 4 GPS speed (digital display –... -
Page 44: Alarms
7.4.2 Alarm Page If the data stations in the system record an event, the correspond- ing information reaches the display AHD 880 TC via the communi- cations bus. The message is evaluated according to its category – pre-alarm, alarm, or sensor error – and then displayed. The display automatically switches over to the alarm page and enters the alarm with its date and time into the alarm list. - Page 45 8.8“ Touchscreen Colour Display AHD 880 TC Operation All events are listed on the alarm page in tabular format. The order is chronological and corresponds to each message’s date and time. The last recorded alarm is always at the top of this list.
-
Page 46: Alarm Acknowledgement
8.8“ Touchscreen Colour Display AHD 880 TC Operation alarm. Key “Optical Acknowledgement“ Key press acknowledges all pending alarms optically. A blinking LED/display changes to a continuously lit display. Key “Next Alarm Page“ Key press pulls up the next existing alarm page. Unless another page exists, the key press is ignored. -
Page 47: Configuration Page Standard Settings
8.8“ Touchscreen Colour Display AHD 880 TC Operation 7.5.1 Configuration Page Standard Settings Launching the Configuration Page This key launches the configuration page. This page displays the current device configurations and the cur- rently selected display options. Operating Key Functions on the Configuration Page Standard Settings Key “Switch to Alarm Page”... -
Page 48: Making Changes
8.8“ Touchscreen Colour Display AHD 880 TC Operation vice to its normal operating condition. Key “Advanced” Key press switches to the configuration page with the advanced set- tings. Key “Next Step / Increase Value” After selecting and marking a parameter that is to be changed, acti- vating this key selects the next possible step or increases a numeric value by 1. - Page 49 8.8“ Touchscreen Colour Display AHD 880 TC Operation The selected parameters can be set to the desired value with the “Next Step / Increase Value” or “Previous Step / Decrease Value” keys: The parameter “Units” allows to switch between the two following unit systems: ...
- Page 50 8.8“ Touchscreen Colour Display AHD 880 TC Operation 00 – 59 Minutes 12/24h am/pm for 12h display for 24h display Display Language German English Italian Spanish French Chinese, traditional Chinese, simplified TIP! The selected language is used on the instrument and alarm pages.
-
Page 51: Configuration Page Advanced Settings
8.8“ Touchscreen Colour Display AHD 880 TC Operation 7.5.3 Configuration Page Advanced Settings Launching the Configuration Page Pressing this key launches the configuration page with the ad- vanced settings: The configuration page with the advanced settings offers additional parameters. Logo Power up The parameters are set as described in the previous chapter. - Page 52 8.8“ Touchscreen Colour Display AHD 880 TC Operation Operating Key Functions on the Configuration Page Advanced Settings Key “Switch to Alarm Page” Key press changes the display to the alarm page. Key for acknowledging the acoustic signal (“Quit Horn”) Key press deactivates internal horn and any connected signal de- vices.
-
Page 53: Measuring Points List / Service Page
8.8“ Touchscreen Colour Display AHD 880 TC Operation Measuring Points List / Service Page This page allows for a full overview of all measuring points in the system, which are visualized on the display. This function is espe- cially helpful when searching for errors. - Page 54 8.8“ Touchscreen Colour Display AHD 880 TC Operation Functions of Operating Keys on the Configuration Page Advanced Settings Key “Switch to Alarm Page” Key press changes the display to the alarm page. Key for acknowledging the acoustic signal (“Quit Horn”) Key press deactivates internal horn and any connected signal devices.
-
Page 55: Information Page
8.8“ Touchscreen Colour Display AHD 880 TC Operation Information Page The information page contains general information, such as the software version, manufacture and commissioning dates, as well as internal “settings” and the display’s hours of runtime. Launch the Information Page Mark the “System Information”... -
Page 56: Brightness Control
If the device cools off, the lighting automatically pow- ers back on. Power Off The Color Display AHD 880 TC is completely powered off by switching off the connected power supply. TIP! It is not possible to fully power off the device with the “Power”... -
Page 57: Maintenance
8.8“ Touchscreen Colour Display AHD 880 TC Maintenance 8 Maintenance TIP! Generally speaking, the Color Display AHD 880 TC is maintenance free. Maintenance of the units is limited merely to external cleaning and inspection. Only use solvent free and nonabrasive detergents for cleaning. -
Page 58: Errors
8.8“ Touchscreen Colour Display AHD 880 TC Errors 9 Errors The following table describes errors that may occur during the op- eration of the Color Display AHD 880 TC and provides information regarding causes, diagnosis, and error correction. Safety ... -
Page 59: Power / Fault Led
Power / Fault LED The LEDs on the device front provide information about the condi- tion of the Color Display AHD 880 TC. The Power LED is lit continuously as soon as the device is con- nected to the supply power. When it extinguishes, the supply volt- age is either too low, or it is interrupted. -
Page 60: Error Correction
8.8“ Touchscreen Colour Display AHD 880 TC Errors Error Correction Error Possible cause Diagnosis / Error Correction Device does not power up. - circuit breaker in the corre- - check connections sponding power distribution not switched on - connecting cables for power... -
Page 61: Disassembly
8.8“ Touchscreen Colour Display AHD 880 TC Disassembly 10 Disassembly After the device has reached its end of life, it must be disassem- bled and disposed in an environmentally safe manner. 10.1 Safety Personnel Only specially trained personnel may disassemble the device. -
Page 62: Disposal
8.8“ Touchscreen Colour Display AHD 880 TC Disassembly 10.3 Disposal In the absence of a return or disposal agreement, recycle the dis- assembled components: Scrap metals. Recycle plastic components. Dispose the other components according to their material properties. -
Page 63: Index
Device Dimensions Color Display AHD 880 TC . 20 Panel Cutout and Drill Holes AHD 650R .... 23 Device Dimensions Remote Control AHD 650R 22 Panel Cutout and Drill Holes AHD 880 TC ..21 DIP-Switch Functions ......... 26 Parameter Selection ........... 48 Disassembly ............ - Page 64 8.8“ Touchscreen Colour Display AHD 880 TC Index Power LED ............59 Power Off ............56 Technical Data Color Display AHD 880 TC ..17 Power Up Modes ..........51 Technical Data Remote Control AHD 650R ..19 Technical Information ......... 17 Safety ..............
- Page 65 Devices, System Installation, Monitoring and Control Technology, Ship Automation Böning Automationstechnologie GmbH & Co. KG Am Steenöver 4 D-27777 Ganderkesee E-Mail: info@boening.com Internet: www.boening.com Texts and illustrations not binding. We reserve the right to make changes due to technical improvements.
Need help?
Do you have a question about the AHD 880 TC and is the answer not in the manual?
Questions and answers