DMX Channel Values In-Depth (8-Channel Mode) Troubleshooting 5. Appendix A Quick DMX Lesson Keeping Your Flurry™ 5 As Good As New Returns (Gasp!) Shipping Issues Tech Specs Page 2 Flurry™ 5 User Manual Rev. A (c) 2013 Blizzard Lighting, LLC...
Blizzard Lighting™ assumes no responsibility or liability for any errors or omissions that may appear in this user manual. Blizzard Lighting™ reserves the right to update the existing document or to create a new document to correct any errors or omissions at any time.
• Avoid direct eye exposure to the light source while it is on. Caution! There are no user serviceable parts inside the unit. Do not open the housing or attempt any repairs yourself. In the unlikely event your unit may require service, please contact Blizzard Lighting at sup- port@blizzardlighting.com. Page 4 Flurry™ 5 User Manual Rev. A (c) 2013 Blizzard Lighting, LLC...
Channel What It Does Pan Fine (16-Bit) Tilt Tilt Fine (16-Bit) Dimmer Red Intensity Green Intensity Blue Intensity Amber Intensity White Intensity Color Macros Strobe Sound Active Page 5 Flurry™ 5 User Manual Rev. A (c) 2013 Blizzard Lighting, LLC...
Blue Intensity Amber Intensity White Intensity 7* 15-watt 5-in-1 LED’s Head Readout Control Panel Figure 2: The Rear Connections DMX In DMX Out AC Power Fuse Cover 110V/220V Switch Page 6 Flurry™ 5 User Manual Rev. A (c) 2013 Blizzard Lighting, LLC...
Maximum capacitance between conductors – 30 pF/ft. Maximum capacitance between conductor & shield – 55 pF/ft. Maximum resistance of 20 ohms / 1000 ft. Nominal impedance 100 – 140 ohms Page 7 Flurry™ 5 User Manual Rev. A (c) 2013 Blizzard Lighting, LLC...
We recommend connecting the fixtures in terms of their proximity to the controller, rather than connecting the lowest fixture number first, and so on. Step 3: Connect other fixtures in the chain from output to input as above. Place a DMX terminator on the output of the final fixture to ensure best communication. Page 8 Flurry™ 5 User Manual Rev. A (c) 2013 Blizzard Lighting, LLC...
Do not mount to surfaces with unknown strength, and ensure properly “rated” rigging is used when mounting fixutres overhead. Adjust the angle of the fixture by loosening both knobs and tilting the fixture. After finding the desired position, retighten both knobs. • When selecting installation location, take into consideration lamp replacement access (if applicable) and routine maintenance. • Safety cables MUST ALWAYS be used. • Never mount in places where the fixture will be exposed to rain, high humidity, extreme temperature changes or restricted ventilation. Page 9 Flurry™ 5 User Manual Rev. A (c) 2013 Blizzard Lighting, LLC...
Press the <ENTER> button to select the menu function currently displayed, or to enable a menu option. To return to the previ- ous option or menu without changing the value, press the <MENU> button. Page 10 Flurry™ 5 User Manual Rev. A (c) 2013 Blizzard Lighting, LLC...
0 (lowest) and 255 (highest) Anbr - UhIT NOTE: Color balance adjustment is accessed by holding the <ENTER> button for 5 seconds while in any operating mode. Page 11 Flurry™ 5 User Manual Rev. A (c) 2013 Blizzard Lighting, LLC...
0 (lowest) and 255 (highest), then press <ENTER> to confirm your selection. 5.) Press and hold the <MENU> button for approximately 5 seconds to return to the previous operating mode. Note: The fixture’s default/factory setting is with all colors set to 255. Page 12 Flurry™ 5 User Manual Rev. A (c) 2013 Blizzard Lighting, LLC...
Allows the unit to be controlled by any universal DMX controller. If you are unfamiliar with DMX, please read the DMX Primer on page #17. A001 1.) The default mode for the fixture is DMX, which appears as on the LED Readout. Page 13 Flurry™ 5 User Manual Rev. A (c) 2013 Blizzard Lighting, LLC...
Verify remote is correct type (CA-9 or other as applicable.) Fixture Moving Verify proper mode of operation. Is the fixture in “Auto” On Its Own mode? If your problem isn’t listed, or if problems persist, please contact support: support@blizzardlighting.com. Page 15 Flurry™ 5 User Manual Rev. A (c) 2013 Blizzard Lighting, LLC...
DMX receiver back to a DMX source. Generally, the “Secondary” channel is not used so data flows only from sources to receivers. Hence, most of us are most familiar with DMX-512 as being employer over typical 3-pin “mic cables,” although this does not conform to the defined standard. Page 16 Flurry™ 5 User Manual Rev. A (c) 2013 Blizzard Lighting, LLC...
Damage incurred in shipping is the responsibility of the shipper, and must be reported to the carrier immediately upon receipt of the items. Claims must be made within seven (7) days of receipt. Page 18 Flurry™ 5 User Manual Rev. A (c) 2013 Blizzard Lighting, LLC...
3-pin XLR Female Other Information If vegetarians eat vegetables, what do humanitarians eat? 2-year limited warranty, does not cover mal- Warranty function caused by damage to LED’s. Page 19 Flurry™ 5 User Manual Rev. A (c) 2013 Blizzard Lighting, LLC...
Page 20
Enjoy your product! Our sincerest thanks for your purchase! --The team @ Blizzard Lighting...
Need help?
Do you have a question about the Flurry 5 and is the answer not in the manual?
Questions and answers