Related Manuals for Buffalo GF539
Summary of Contents for Buffalo GF539
- Page 1 Hot Drinks Dispenser Instruction Manual Model . Modéle . Modell . Modello . Modelo . Malli GF539...
-
Page 2: Safety Tips
Keep all packaging away from children. Dispose of the packaging in accordance to the regulations of local authorities. If the power cord is damaged, it must be replaced by a BUFFALO agent or a recommended qualified technician in order to avoid a hazard. -
Page 3: Operation
Operation Filling the water boiler tank Make sure the power switch is set to OFF. Remove the lid to the water boiler tank (Fig 1) Fill the tank with water until it reaches the MAX fill line (Fig 2). Filling the Bowl Remove the lid and pour the beverage prepared according to the manufacturer’s instructions into the... - Page 4 Turn on the power using the green switch (Fig 4). Switch will illuminate when machine is on. Set the thermostat to the required temperature (Fig 5). Dispensing the product Warning: The products dispensed from the machine can be hot please take care to avoid risk of scalding Place a suitable cup beneath the tap Push or pull the lever on the tap until the required amount of product has...
-
Page 5: Cleaning And Maintenance
If the product to be dispensed is especially thick pull the tap Rod out to the maximum position (Fig 7) Any clogging in the dispensing line may be removed by sliding the tap rod back and forth (Fig 7) Warning: never touch the bowl or lid while the machine is operating, since they are very hot; always use the handle when moving the bowl lid Cleaning and Maintenance Emptying the bowl... - Page 6 Removing and cleaning the bowl Warning: before removing the bowl, make sure that the main switch is off, the unit is unplugged from the mains and that the bowl is empty and sufficiently cooled down Remove the lid (Fig 9) Slide the mixing paddle upwards to remove it, keeping it in line with the central rod until the bottom slot of the...
- Page 7 Unlock the bowl clips as illustrated in Fig 12, to free the bowl from the machine body; Release the bowl from the machine body, using two fingers to prise it away from the fixed steel part of the mixer rod (A) and the others to grip the outlet edge of the bowl(B) (Fig 13) Gradually pull the bowl harder until it comes away from its seating;...
- Page 8 Place the bowl on a flat surface and using both hands, remove the gasket by sliding it upwards in the direction shown by the arrow (Fig 16) Wash the disassembled bowl and components with a sanitising detergent solution, rinsing thoroughly with clean hot water.
- Page 9 Removing the tap Ensure the bowl is empty Move the tap rod to the maximum dispensing position (Fig 17) Press the button(A) securing the tap to the machine and then remove the tap with both hands (Fig 18) Cleaning the Water Pan With bowl and tap removed clean the surface of the pan using a damp cloth and/or a non-abrasive sponge (Fig 19)
- Page 10 Clean the channel connecting the bowl and the tap, using a cleaning brush (included) (fig 20) Refit the tap; Pour a little water inside the pan; Use the tap to drain out all water from the pan so as to eliminate any small product residues inside the dispensing channel.
- Page 11 Pull the lever (D) all the way out from the knob(E) then push the lever(F) upwards from bottom until it comes out from the pin guide (Fig 23). Unscrew the knob E by turning anti-clockwise while holding the rod in place. Pull out the rod (G) and spring (H) from the tap body (the pin/gasket assembly (I) will slide out together with the rod) (Fig 24)
- Page 12 Disassemble (by pulling) the pin (L) from the gasket (M) (Fig 26) Wash the disassembled components with a sanitising detergent solution, rinsing thoroughly with clean hot water. Reassemble the tap by reversing the disassembly instructions. To fit the lever(F) push the rod (D) from the inside until the guides protrude;...
- Page 13 Cleaning the Drip Tray The drip tray should be emptied and cleaned daily. Note: the tray needs to be emptied out and cleaned every time that the red float fitted to the grid rises, this is to stop liquid from leaking out. Lift the tray with grid and pull it outwards to remove it from its seating.
- Page 14 Emptying the boiler Tank Warning: While the boiler is being emptied, the machine must be unplugged. The boiler may be emptied only when the bowl is empty and the machine has cooled down sufficiently. Remove the drip tray Remove the cap (A) (Fig 31) Place the machine on a flat surface Place a container (B) with a capacity of more than 3 litres underneath the bleeder cap (C)
- Page 15 Make sure the machine is plugged in not turn correctly Mixing rod not fitted correctly Ensure mixing rod is correctly fitted Motor Fault Call Buffalo agent or qualified technician Switch set to OFF Set the switch to ON Tap leaks Tap not fitted correctly...
-
Page 16: Technical Specification
BUFFALO. Every effort is made to ensure all details are correct at the time of going to press, however, BUFFALO reserve the right to change specifications without notice... -
Page 17: Declaration Of Conformity
Hot Drinks Dispenser Tipo di apparecchiatura • Tipo de equipo • Tipo de equipamento Model • Modèle • Modell • Modello • Modelo • Malli GF539 Application of Council Directives(s) LVD Directive 2006/95/EC Toepassing van Europese Richtlijn(en) • Application de la/des directive(s) EMC Directive 2004/108/EC du Conseil •...