Summary of Contents for Medium Link MLS-200-C
- Page 1 MLS-200-C 100/95 Mbps VDSL2 (Long Reach Ethernet) Ethernet Bridge (Combo Interface For Copper or Coaxial) User’s Guide Version:1.0.E...
-
Page 2: Fcc Warning
COPYRIGHT All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, whether electronic, mechanical, photo copying, recording or otherwise, without the prior written permission of the publisher. FCC WARNING This equipment has been tested and found to comply with the limits for a class B device, pursuant to part 15 of FCC rules. -
Page 3: Key Features
INTRODUCTION MLS-200-C is the LRE(Long Reach Ethernet) bridge that efficiently extends 10/100 Ethernet circuits to 2 wire-Networking LAN for Internet and Intranet access. Over 915 meters (3,000feet) at 50/80Mbps using existing phone/Coaxial wire. This modem will allow Ethernet connectivity in existing facilities without pulling extra cable. - Page 4 -- 2...
-
Page 5: Led Indicators On The Front Panel
LED Indicators on the Front Panel Status Glowing Dimming Flashing POWER DC 12 power feeding in Not powered LAN1~4 Link/Act LAN Link Disconnected or Link Received or Transmit failed LINE CPE CPE side Mode CO side Mode LINE Link/Act VDSL2 Link Slow Flashing mean Link failed or Fast Flashing mean... - Page 6 Ports on the Real Panel Port Name Type Functions DC IN DC 12V Connects to the power adapter plug. CONFIG DIP SW CONFIG for MODEM LAN1~4 RJ45 Connects to Ethernet port on FTTx/xDSL Modem or Switch for Internet Access. Line/Phone RJ11 Pin 3-4 : Connects from wall outlet LINE in or connects to VDSL2 devices.
- Page 7 Essential Hardware’s Items Included Description Purpose VDSL2 Ethernet Bridge modem Main Unit DC 12V Power Adapter Connects from Power Port of the main unit into a wall outlet (INPUT: 100~240V, 50~60Hz, 0.5A) -- 5...
-
Page 8: Hardware Connections
Hardware Connections The figure about shows how to connect an xDSL modem to a phone line network. Follow the same steps to connect and Ethernet device such as HUB or AP, to a phone line network. Now you should have connected the Ethernet port, Line port and the Power port to the appropriate devices or lines. -
Page 9: Troubleshooting
TROUBLESHOOTING The Bride had been designed to be a reliable and easy to use connection device. Please refer to the list below to aid in troubleshooting. The Power (green) LED is off Make sure the power adapter is properly plugged into a live electrical outlet. The LAN (Ethernet) or Line Link/Act LED is off. -
Page 10: Specifications
Specifications Network Standards IEEE802.3 10BASE-T, 10Mbit/s IEEE802.3u 100BASE-TX, Fast Ethernet at 100Mbit/s, Auto-negoatiaton IEEE802.3x Full Duplex and Flow Control Protocol: Transparent to higher layer protocols Connectors Fast Ethernet：Four RJ45 Connectors RJ11：One RJ11 Female Connectors，pin 3-4 for Link line，pin 5-6 for Phone ... - Page 11 MLS-200 : 1 WAN, 2 *10/100 TX Ethernet Extender over Copper Line MLS-200-C : 1 WAN, 4 *10/100 TX Ethernet Extender over Copper/Coax Line MLS-202-C : 2 WAN, 4 *10/100 TX Ethernet Extender over Copper/Coax Line Contact Information: Email: jack@ems5.com...
- Page 12 Appendix (PHY Link Rate reference Table) using AWG26 Copper 100M/95M 100M/95M 100M/60M 100M/60M Profile Communication Profile Line rate Profile Line rate Profile Line rate Line rate distance(meter) (Download Mbps) (Upload Mbps) (Download Mbps) (Upload Mbps) 86.3 85.7 60.7 47.8 81.4 38.2 34.2 26.4...
- Page 13 100/60 P H Y L ink R ate T able D ow nload M bps U pload M bps D istance 100/95 P H Y L ink R ate T able D ow nload M bps U pload M bps D istance 100/95 P H Y L ink R ate T able D ow nload M bps...
Need help?
Do you have a question about the MLS-200-C and is the answer not in the manual?
Questions and answers