Do you have a question about the EH1450 and is the answer not in the manual?
Questions and answers
Summary of Contents for Elite EH1450
Page 1
EH1450 2.7 kW Patio Heater 2700 W maximum heat output 3 Heat settings Independent 28 W downlight Remote control Suitable for outdoor use Page 1...
IMPORTANT Installer and Users please note: These instructions should be read carefully and left with the user of the product for future reference. BEFORE USE You must inspect the appliance including its cable and plug for any signs of damage. If the product is damaged, DO NOT use it, and contact your supplier immediately.
Page 3
ASSEMBLY The following fasteners are supplied: 22 off M4 x 10 mm machine screw (a machine screw has a fine thread which is the same diameter throughout) 9 off 4.8 mm x 20 mm self-tapping screw (a self-tapping screw has a coarse thread and is tapered towards the point) 3 off 4 mm washer 6 off 3.5 mm x 12 mm self-tapping screw 3 off masonry-fixing plug...
Page 4
Choose a position for the appliance, at least 1.5 m from the nearest wall, making sure that there is a gap of at least 600 mm between the top of the heater and any cailing or canopy. three ground-anchor points to the underside of the base using six 3.5 mm x 12 mm self-tapping screws Page 4...
Page 5
Then slide each leg onto the projection from the underneath of the main body, and fix in place with two M4 x 10 mm machine screws . Then fix the legs to the base using twelve M4 x 10 mm machine screws Page 5...
Page 6
Attach two of the three side panels to the legs. The panel clips in place at the top and is fixed by two M4 x 10 mm machine screws at the bottom. Attach the knob to the final panel, and attach the chain to the hook inside the main assembly, then clip the cable to the underneath of the base.
In order to prevent theft, or to keep the appliance stable where there is a possibility of strong winds, it should be fixed to the ground using the three anchor points provided. Using the appliance as a template mark the positions of the holes on the floor, then drill three holes into the floor using a masonry drill and insert the plastic masonry plugs Fix the appliance to the floor using the three 4.8 mm x 25mm...
circular indicator beneath heating element illuminates if the element is switched on - this makes it possible to tell if an element is switched ON before it has reached operating temperature, or if it is switched OFF and has yet to cool down. The push-button labelled L controls the lamp at the top of the appliance.
smoke alarms (it is mandatory for new buildings). PRODUCT SAFETY • This appliance is not intended for use by persons (including children) with reduced physical, sensory mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
At time of going to press, the average cost of electricity is £0.12 per unit (kilowatt-hour). The amount you are being charged will be shown on your electricity bill. At this cost, the EH1450 will cost £0.32 per hour to run with all three elements operating. MAINTENANCE Before cleaning, turn the heater off, disconnect from the mains supply and allow to cool down.
If the mains lead is damaged, it must be replaced by the manufacturer or and authorised service centre. If the mains plug needs to be replaced, proceed as follows: • Connect the brown wire to the terminal labelled "L". • Connect the blue wire to the terminal labelled "N".
SERVICE WARRANTY Prem-i-Air guarantees the product free from defects in materials and workmanship for a period of two years. Should this appliance be operated under conditions other than those recommended, at voltages other than the voltage indicated on the appliance, or any attempts made to service or modify the appliance, then the warranty will be rendered void.
Need help?
Do you have a question about the EH1450 and is the answer not in the manual?
Questions and answers