v.link VL2-MBN45 Manual

For mercedes benz vehicles generation ntg4.5-204 with comand online, audio50 aps or audio 20 with 4pin hsd lvds connector on the monitor

Advertisement

Quick Links

for Mercedes Benz vehicles
generation NTG4.5-204 with
Comand Online, Audio50 APS or Audio 20
with 4pin HSD LVDS connector on the monitor
Video-inserter with 2 video + RGB + rear-view camera input and CAN control
Product features
 Video-inserter for factory-infotainment monitors
 2 video-inputs for after-market devices (e.g. DVD-Player, DVB-T tuner, ...)
 Built-in audio-switch (no audio-insertion)
 Rear-view camera video-input
 Automatic switching to rear-view camera input on engagement of reverse gear
 RGB-input for after-market navigation
 Video-in-motion (ONLY for connected video-sources)
 Compatible with factory rear-view camera
 AV-inputs PAL/NTSC compatible
Version 09.02.2012
v.LiNK Video-inserter
VL2-MBN45

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the VL2-MBN45 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for v.link VL2-MBN45

  • Page 1 Video-inserter VL2-MBN45 for Mercedes Benz vehicles generation NTG4.5-204 with Comand Online, Audio50 APS or Audio 20 with 4pin HSD LVDS connector on the monitor Video-inserter with 2 video + RGB + rear-view camera input and CAN control Product features ...
  • Page 2: Table Of Contents

    Video-sources to IN1 and IN2 2.5.2. Audio-switch and audio-insertion 2.5.3. After-market rear-view camera 2.5.4. After-market navigation 2.6. Connecting video-interface and keypad 2.7. Picture settings 3. Interface operation 3.1. By Comand-buttons 3.2. By keypad 4. Specifications 5. Connections (video-interface) 6. Technical support Version 09.02.2012 VL2-MBN45...
  • Page 3: Prior To Installation

    Technical knowledge is necessary for installation. The place of installation must be free of moisture and away from heat sources. 1.1. Delivery contents Take down the serial number of the interface and store this manual for support purposes: ____________________ Version 09.02.2012 VL2-MBN45...
  • Page 4: Checking The Compatibility Of Vehicle And Accessories

    To the video interface’s RGB-input it is possible to connect a RGB- or a VGA-video source. Set dip 4 according to table. Recommended resolution for VGA is 800x600 @ 60Hz. After-Market Navigation Dip 4 VGA (RGB-Input Pin 4 H-Sync, Pin 8 V-Sync) RGB NTSC Note: VGA-mode is only possible on the 7“-monitor. Version 09.02.2012 VL2-MBN45...
  • Page 5: Enabling The Interface's Video Inputs (Dip 1-3)

    If power source is not taken directly from the battery, the connection has to be checked for being start-up proven and permanent. 2.1. Place of installation The interface is installed on the backside of factory monitor. Version 09.02.2012 VL2-MBN45...
  • Page 6: Connection Schema

    2.2. Connection schema Version 09.02.2012 VL2-MBN45...
  • Page 7: Connecting Video-Interface And Can-Box

    Note: Check LEDs on video-interface after reconnecting the battery, one must be on. Note: No liability for vehicle wire colours and pin definition! Possible changes by the vehicle manufacturer. The given information must be verified by the installer. Version 09.02.2012 VL2-MBN45...
  • Page 8: Connection To The Factory Monitor

    Remove female 8pin MB connector of factory harness from the rear of the factory monitor and connect it to the male 8pin MB connector of the 4pin cable. Connect female 8pin MB connector of the 4pin cable to the male 8pin MB connector of the factory monitor. Version 09.02.2012 VL2-MBN45...
  • Page 9: Connecting Peripheral Devices

    It is possible to switch the audio signals from the to IN1 and IN2 connected AV-sources parallel to the video-signal of the respective AV-source by video-interface’s built-in audio- switch. Version 09.02.2012 VL2-MBN45...
  • Page 10 Audio input signal R/L of source IN1 Audio output signal R/L of factory audio AUX or FM-modulator Ground No function Note: When switching the video interface from video-IN1 to video-IN2, the audio will also automatically be switched. Version 09.02.2012 VL2-MBN45...
  • Page 11: After-Market Rear-View Camera

    Connect female 8pin connector of the RGB cable to the male 8pin connector of the video-interface. The loose grey wires have no function and have to be isolated. Connect male 6pin connector of the RGB cable to the after-Market navigation. Version 09.02.2012 VL2-MBN45...
  • Page 12: Connecting Video-Interface And Keypad

    Press the MENU button to open settings menu on the OSD and to switch to the next setting. UP and DOWN change the corresponding values. The buttons are embedded in the housing to avoid accidental changes during or after installation. Version 09.02.2012 VL2-MBN45...
  • Page 13: Interface Operation

    Power consumption 2.4W Video input 0.7V~1V Video input formats PAL/NTSC RGB-video amplitude 0.7V with 75 Ohm impedance Temperature range -40°C to +85°C Weight 195g Dimensions (box only) B x H x T 182 x 24 x 100 mm Version 09.02.2012 VL2-MBN45...
  • Page 14: Connections (Video-Interface)

    5. Connections (video-interface) 6. Technical Support NavLinkz GmbH Caraudio-Systems Vertriebs GmbH distribution/tech dealer-support distribution Eurotec-Ring 45 Rheinhorststr. 22 D-47445 Moers D-67071 Ludwigshafen am Rhein +49 180 3 907050 Email mail@navlinkz.de Version 09.02.2012 VL2-MBN45...

Table of Contents