Summary of Contents for PROFILO LED 150
- Page 1 PROFILO LED 150 User’s Manual rel 1.1 GB D.T.S. Illuminazione s.r.l. – ITALY http://www.dts-lighting.it Made in Italy...
- Page 2 Le informazioni contenute in questo documento sono state attentamente redatte e controllate. Tuttavia non è assunta alcuna responsabilità per eventuali inesattezze. Tutti i diritti sono riservati e questo documento non può essere copiato, fotocopiato, riprodotto per intero o in parte senza previo consenso scritto della D.T.S . D.T.S.
-
Page 3: Table Of Contents
INDEX: 1- SYMBOLS 2- GENERAL WARNING 3- GENERAL WARRANTY CONDITION 4- TECHNICAL FEATURES 5- MAIN ELECTRICAL CHARACTERISTICS 6- ACCESSORIES 7- IMPORTANT SAFETY INFORMATION 7.1 Fire prevention 7.2 Prevention of electric shock 7.3 Safety 8- INPUT / OUTPUT CONNECTIONS 9- DMX SIGNAL CONNECTION 9.1 DMX Addresses 9.2 Selecting the DMX address 10- FIRMWARE UPDATING... -
Page 4: 1- Symbols
1- SYMBOLS Graphic symbols used on this manual THIS SYMBOL INDICATES A HOT SURFACE THIS SYMBOL INDICATES ELECTRIC SHOCK RISK THIS SYMBOL INDICATES GENERAL RISK THIS SYMBOL MEANS “DO NOT PLACE THE UNIT ON INFLAMMABLE SURFACES” THIS SYMBOL INDICATES THE MINIMUM 30cm DISTANCE TO BE KEPT BETWEEN THE DEVICE AND THE LIT OBJECT... -
Page 5: 4- Technical Features
The dimming curves are similar to those of halogen lamps. The connectors are Powercon In & Out and 5 poles DMX In & Out. PROFILO LED 150 is contained in a strong housing with folded edges, designed to resist all the rigors of continuous use. -
Page 6: 5- Main Electrical Characteristics
5- MAIN ELECTRICAL CHARACTERISTICS Input Voltage Range : Vin 90 - 260 Vac Frequency : 50 / 60 Hz Power Consumption Range : 5 - 160 W Power Factor (Pf) : 0.95 electronic PFC controller Efficiency : 95% typical Control Input: Control Signal : DMX 512 Dimming System : Constant Current PWM Address Range : DMX 512 channels addressable by display... -
Page 7: 7- Important Safety Information
LED 150 unit. Use only AC supplies 90-260V, 50 / 60 Hz. PROFILO LED 150 should never be located in position exposed to rain or in areas of extreme humidity. A good air ventilation is essential for proper equipment work. -
Page 8: 9- Dmx Signal Connection
9- DMX SIGNAL CONNECTION: The unit operates using a digital DMX 512 signal. Connection between the controller and the unit or between units must be carried out using a two pair screened ø 0.5 mm. Ensure that the conductors do not touch each other. Do not connect the cable ground to the DMX connector chassis. -
Page 9: Dmx Addresses
This procedure require a base knowledge of Windows computer applications. Please refer to an authorised D.T.S. service centre. To update the software version of the PROFILO LED 150 you need: D.T.S. RED BOX interface (D.T.S. Code: 03.LA.008). USB-DMX Driver for the D.T.S. RED BOX interface. -
Page 10: 11- Display Functions
11- DISPLAY FUNCTIONS DISPLAY FUNCTIONS The PROFILO LED 150 display panel shows all the available functions . Using these functions, it is possible to change some of the parameters and add some functions. Changing the D.T.S. setting can vary the functions of the unit so that it does not respond to the DMX 512 used to control it. - Page 11 (D.T.S. Code: 03.LA.016) ENTER INFRARED MODE Infrared remote control. By activating Ir Mode, it will be possible to navigate trought the unit functions by using NOT IMPLEMENTED ON PROFILO LED 150 the D.T.S. infrared remote control (D.T.S. Code: 0514L008)
- Page 12 To log PROFILO LED 150 off from a transmitter simply select UNLINK function under WIRELESS DMX MENU and press ENTER. When PROFILO LED 150 is logged off, the display is blinking, meaning its available for log in on a new transmitter. Logging out a PROFILO LED 150 Select UNLINK function under WIRELESS DMX MENU and press ENTER.
- Page 13 Default = OFF MENU Up-Down ENTER Up-Down ENTER ENTER Up-Down EMERGENCY Emergency operating mode. ENTER By setting Emergency mode, it Default = 255 will be possible to select Dimmer intensity level that will ENTER then ran if DMX signal is missing or not available.
-
Page 14: 12- Service Menu
PC or Fresnel ENTER lens selection ENTER ENTER Up-Down PRODUCT ENTER Product model selection PROFILO LED 150 (Def.) or SCENA LED 150 ENTER ENTER Up-Down CURRENT From min 20 mA to max 600 mA Default = 300 mA ENTER ENTER... -
Page 15: 13- Dmx Protocol
ENTER ENTER RESM To restore service and user default settings ENTER EXIT Exit from service menu 13- DMX PROTOCOL 2 CHANNELS MODE SHUTTER / STROBE DIMMER DMX CHANNEL Parameter: SHUTTER / STROBE Function DMX range Mid Point Move Range Mode Option Value (degrees) - Page 16 The information contained in this publication has been carefully prepared and checked. However, no responsibility will be taken for any errors. All rights are reserved and this document cannot be copied, photocopied or reproduced, in part or completely, without prior written consent from D.T.S. D.T.S.
Need help?
Do you have a question about the LED 150 and is the answer not in the manual?
Questions and answers