Summary of Contents for Quiet Power QP100 Series
- Page 1 Installation a nd O peration M anual Quiet P ower Dual U SB C harger QP100 S eries ...
-
Page 2: Table Of Contents
Quiet Power USB Charger Installation and Operation Manual TABLE OF CONTENTS REVISION H ISTORY ............................... 4 GENERAL D ESCRIPTION .......................... 5 .............................. 5 NTRODUCTION .......................... 5 QUIPMENT ... - Page 3 (ii) damage caused by service performed by another party; (iii) cosmetic damage, such as scratches, nicks and dents; or (iv) damage to a product that has been modified or altered. Quiet Power LLC and its parent, Summit Avionics, reserve the right to refuse warranty claims against products or services that are obtained and/or used in contravention of the laws of any country.
-
Page 4: Revision H Istory
Quiet Power USB Charger Installation and Operation Manual REVISION H ISTORY Date Revision Description 7/24/2014 Original Release 7/30/2014 Corrected wiring reference in section 4 Added available models & options (Section 1.4) 1/7/2015 Added circuit breaker value table in Appendix B, revised mechanical installation drawings to include mounting with #4-40 or #6-32 screws. -
Page 5: General Description
EMI / RFI emissions from other similar devices. 1.2 Equipment Description The Quiet Power line of USB chargers are engineered for use in aircraft cockpit or cabin applications. They provide regulated, filtered D.C. power to common Portable Electronic Devices (PED) to power these units during flight and charge their internal battery. -
Page 6: Technical Specifications
1.2.1 Lighted Models All of the QP100 series chargers are available with connector backlighting. These units are ordered with a “-L” designator on the model number ( e.g. QP-104-L). The backlighting is on continuously and projects a soft blue light within the USB connector entrance. -
Page 7: Regulatory Compliance
Quiet Power panel or a fabricated panel. You may choose to install the Quiet Power device using either #6-32 screws or #4-40 screws. The #6-32 screws are aligned along the device vertical centerline and the #4-40 screws are adjacent to the connector. -
Page 8: Installation
Install the unit in the instrument panel by cutting or punching an opening in accordance with Appendix C. Install the Quiet Power unit from the rear and secure with the chosen screws. Wire the harness in to the aircraft electrical system per the diagram shown in Section 7.2 (Red wire to the protective device, White to aircraft ground). -
Page 9: Documentation
Quiet Power USB Charger Installation and Operation Manual Decimal d imensions s hown i n m etric u nits Figure 1 - Charger Power Connector Install a placard near the connector with one of the following statements, depending on the model and auxiliary charger output voltage: “5 volts 1 amp”... -
Page 10: Logbook Entry
Quiet Power USB Charger Installation and Operation Manual 5.2 Logbook Entry Complete an aircraft / airframe logbook entry detailing the installation and post installation tests performed, Note the tests performed by referencing Section 6 Post-Installation Tests (e.g. Tested to installation manual P/N 98-790002 Rev 2 Sections 6.2 (Compass) and 6.3 (Operational) –... -
Page 11: Post-Installation Tests
6. Post-Installation Tests 6.1 EMI / RFI Test Procedure and Log After installation of the Quiet Power unit and confirmation of normal operation on aircraft battery power, an EMI / RFI check may be performed in accordance with the following ground test procedure. -
Page 12: Hf C Ommunications R Eceiver
_______________________________________________________ 6.1.4 VHF Communications Receiver(s) For each communication receiver, set the squelch to the normal level with the Quiet Power unit powered off. Check each receiver for interference at 1 MHz increments from 118.00 to 136.00 MHz In the table below, place a checkmark in the Interference column if interference is noted at the designated frequency;... -
Page 13: Operational Checks
Installation and Operation Manual 6.3 Operational Checks Connect the desired loads to the Quiet Power unit, either through the USB connector(s) or through the auxiliary charging port. Confirm proper operation of the load device and that the Quiet Power unit is supplying power to the device. -
Page 14: Appendices
Quiet Power USB Charger Installation and Operation Manual 7. Appendices 7.1 Appendix A Environmental Qualification Form DO-160G Section Description Qualification Section 4.0 Temperature and Altitude Section 5.0 Temperature Variation Section 6.0 Humidity Section 7.0 Operational Shocks and Crash Safety Section 8.0 Vibration Section 9.0... -
Page 15: B Interconnect Diagrams
Quiet Power USB Charger Installation and Operation Manual 7.2 Appendix B Interconnect Diagrams The interconnect diagram shown below includes the auxiliary power connections. QP100 units do not include auxiliary power. All variants of the dual-USB connector version, including J1 – T o Q P1xx ... -
Page 16: Drawings
Quiet Power USB Charger Installation and Operation Manual 7.3 Appendix C Mechanical Drawings 7.3.1 Panel Cutout, Direct Panel Mount Two mounting methods are supported – mounting with #6-32 screws or #4-40 screws. #6-32 screws are recommended, Figure 2 - Panel Cutout, #6-32 Mounting Screws... - Page 17 Quiet Power USB Charger Installation and Operation Manual Figure 3 - Panel Cutout, #4-40 Mounting Screws P/N 98-790002 Rev 3 Page 17...
-
Page 18: ¼"Panel Mount Adapter Plate
Quiet Power USB Charger Installation and Operation Manual 7.3.2 2 ¼”Panel Mount Adapter Plate P/N 98-790002 Rev 3 Page 18... -
Page 19: ⅛" Panel Mount Adapter Plate
Quiet Power USB Charger Installation and Operation Manual 7.3.3 3 ⅛” Panel Mount Adapter Plate P/N 98-790002 Rev 3 Page 19...