Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for 66audio REVOLUTION
- Page 1 U S E R G U I D E...
- Page 2 To avoid hearing damage, make sure that the volume on your transmitting device is turned down before connecting your REVOLUTION. After placing the headphones on your ears, gradually turn up the volume until you reach a comfortable listening level. Noise levels are measured in decibels (dB) and exposure to any noise at or above 85 dB can cause gradual hearing loss.
- Page 3 USB charging. Plug the Micro USB charging cable into the charging port of the REVOLUTION located below the Pair button. Plug in the other end of the cable into a USB port on a PC, Mac or USB wall outlet.
- Page 4 Power switch T HE Pair button R EVO LU TION USB charging port 3.5mm audio input Volume + Volume - Microphone ANC (Active Noise Cancellation) switch Folding Hinges LED Indicator Multifunction button This image is for reference only. Please check the product for details.
-
Page 5: Power On/Off
Press and hold the Pair button for 3 seconds until the status LED begins to flash both blue and red. You will also hear an audible “pairing” tone. You are now in Pair Mode and your device will be able to see the REVOLUTION for pairing. - Page 6 You will also hear an audible from the headphones. • If pairing is not successful, switch off the REVOLUTION by sliding the Power button up and then re-pair using to the steps outlined above. •...
-
Page 7: Adjusting Volume
Press the Volume +/- button to adjust the volume. One short press TO M US IC will adjust one interval. When the volume reaches maximum or minimum volume, the REVOLUTION will alert you with an audible tone. Note: Volume can be adjusted using either your headphone or your music device. - Page 8 Note: The audio cable will allow you to listen to music even if the REVOLUTION is turned off. It also allows you to use the REVOLUTION in places where wireless...
- Page 9 Receiving a Phone Call C AL L O PE R AT ION The REVOLUTION is equipped with an omnidirectional, noise-cancelling microphone featuring Clear Voice Capture (cVc®) technology for optimal call clarity. If music is playing while an incoming call is received (or an outgoing call...
-
Page 10: Making A Call
C A LL Making a Call O P E R ATIO N, Use the keypad on your smartphone to dial the desired number. C O N T’D Press the “Send” or “Dial” key on your smartphone to initiate the call. The call is automatically routed to the headphones. -
Page 11: Refusing A Call
C AL L O P E R AT IO N , C O N T ’ D Refusing a Call To refuse an incoming call, press and hold the Multifunction button for 2 seconds until you hear a prompt from the headphones. - Page 12 T R OU B LE - If the headphones disconnect or will not pair, please S H O OTING check the following: • Ensure that the headphones have enough power, are turned on and have been successfully paired to your device.
- Page 13 N E ED H E L P ? Please visit www.66audio.com or simply send an email to support@66audio.com We’re here to ensure you enjoy your headphones and will solve any issues you are experiencing!
- Page 14 • When the battery is nearly empty, the red LED will flash every 30 seconds. You will also hear an audio prompt from the REVOLUTION in the form of short beeps to indicate low battery. • The headphones have the ability to display real-time battery level via a battery meter icon located on-board iOS devices such as the iPhone, iPad and iPod Touch.
- Page 15 Use of these headphones at excessive volumes may cause permanent hearing damage. Always turn down the volume before use. 66audio.com support@66audio.com Copyright © 2015 66 Audio, LLC. All rights reserved. 66 Audio and the 66 Audio logo are registered trademarks of 66 Audio, LLC.
Need help?
Do you have a question about the REVOLUTION and is the answer not in the manual?
Questions and answers