Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Flying Thingz Manuals
  4. Toy
  5. Flag Ship 40
  6. Construction manual

Flying Thingz Flag Ship 40 Construction Manual

Hide thumbs

Advertisement

Quick Links

Download this manual
This booklet divides the construction into sub-assemblies; wing, fuselage, etc. Please read each section carefully before starting on that particular sub-
assembly. There is a complete description of all parts under "Kit Contents" Please check to make sure your kit is complete. We are human, and occasionally
miss something! If you have trouble identifying a part, or are missing something, please contact us and we can help.
During the construction process the steps will outline what part to use. We have used actual pictures instead of unclear or often inaccurate illustrations
to assist in the building process. This manual was intended for English users, and all measurements are made in standard units. (Inch, foot, etc.) This
manual was intended to be used alongside of the plans. Please refer to the plans if any step is unclear.
Should you experience a problem building or flying this kit, we recommend you see your dealer first. If you are unable to solve the problem, feel free to
call or write:
This product is sold with exclusion of all warrantees, expressed or implied, statutory or otherwise.
Pilot assumes all risk in building and operating this model. Refer to and abide by AMA rules at
Flying Thingz
Flag Ship 40
Kit# FT3012
A Sport Scale
Flying Flag
Made In The USA!
About This Construction Manual

Customer Service

Flying Thingz
2075 Grandview St.
Oceanside, CA 92054
support@flyingthingz.com
or online at
Control Models.
www.flyingthingz.com
www.modelaviation.com
for regulations on Radio

Advertisement

loading
Need help?

Need help?

Do you have a question about the Flag Ship 40 and is the answer not in the manual?

Questions and answers

Related Manuals for Flying Thingz Flag Ship 40

Summary of Contents for Flying Thingz Flag Ship 40

  • Page 1: Customer Service

    Flying Thingz Flag Ship 40 Kit# FT3012 A Sport Scale Flying Flag Made In The USA! About This Construction Manual This booklet divides the construction into sub-assemblies; wing, fuselage, etc. Please read each section carefully before starting on that particular sub- assembly.

  • Page 2: Kit Contents

    Coroplast (corrugated plastic) Uncle Sam 9675 Paper Full Color Construction manual (Your Reading It ) 9684 36” x 48” Paper Full size plan sheet 9690 Laser Cut 1/8” balsa Balsa fuselage sides © 2002, 2003 Flying Thingz All Rights Reserved.
  • Page 3 Building pins Scissors accelerate or instantly harden CA (superglue). □ □ □ Alphaic Resin glue (white Razor saw Sanding blocks glue) □ □ □ Small building square Masking tape Epoxy or Polyurethane Paints © 2002, 2003 Flying Thingz All Rights Reserved.
  • Page 4 Use the top and the servo tray to it’s front of the balsa location in front of F2. fuselage for alignment. (Again, check the plans as to what side the ply wood doublers face!) © 2002, 2003 Flying Thingz All Rights Reserved.
  • Page 5 Set the1/8” balsa hatch smooth. under the fuselage and glue your ¼”x¼” stick hatch support rails between F1 and F2. Glue only to the hatch, DO NOT let glue get on the fuselage body. © 2002, 2003 Flying Thingz All Rights Reserved.
  • Page 6 □ Place the center cut out on the wing next to the fuse so there is ¾” from the back of the cut out to the front of the TE. © 2002, 2003 Flying Thingz All Rights Reserved.
  • Page 7 5/32 drill bit to the Elevons from foam, enlarge the gear slot. sand if necessary to remove cutting residue. Cut the 24” elevon in half for each side if the wing. © 2002, 2003 Flying Thingz All Rights Reserved.
  • Page 8 Carefully position the Covering blue stars section on the leading edge of the Right wing. Use care to push out any bubbles. A light misting of water before applying the blue will help placement. © 2002, 2003 Flying Thingz All Rights Reserved.
  • Page 9 Mount the nose gear to the fire wall. Make sure match the wing. to leave enough room for your engine and © 2002, 2003 Flying Thingz All Rights Reserved.
  • Page 10 Make sure to use a Don’t forget to send Pictures sleeve on the outside to eliminate any flexing. Add your wheels and wheel collars to the main and Comments to us! © 2002, 2003 Flying Thingz All Rights Reserved.
  • Page 11 Flying Thingz 2075 Grandview St Oceanside, CA 92054 support@flyingthingz.com or online at www.flyingthingz.com © 2002, 2003 Flying Thingz All Rights Reserved.