Advertisement
Quick Links
Advertisement
Summary of Contents for Tahoe TI3 KGP80B
-
Page 2: Table Of Contents
CONTENTS M A I N T E C H N I C A L PA R A M E T E R A N D S P E C I F I C AT I O N S … 2 ⅠMain Technical Specifications ………………………………………………………2 MAI N S T RU CT URE AND US E ME T H O D…... -
Page 3: M A I N T E C H N I C A L Pa R A M E T E R A N D S P E C I F I C At I O N S
WARNING PLEASE READ AND UNDERSTAND THIS MANUAL COMPLETELY BEFORE OPERATING THE EQUIPMENT. MAIN TECHNICAL PARAMETERS AND SPECIFICATIONS Ⅰ Ⅰ Ⅰ Ⅰ MAIN TECHNICAL SPECFICATIONS GASOLINE PUMPS MODEL KGP80B 80（3”） Inlet/outlet Diameter. (mm) Self-primin Max. head (m) g pump Max. Suction head (m) Max. -
Page 4: Main Structure And Use Method
· · · · MAIN STRUCTURE AND USE METHOD Ⅰ Ⅰ Ⅰ Ⅰ STRUCTURE This type of pump consists of gasoline/diesel engine and water pump which drove by a same driving axle. The pump is fixed on a frame through shock absorber device, so it compact in structure and convenience for use of movement. - Page 5 continuous to be used after adding an adjustment shim on the shaft shoulder. Fig .1 Structure diagram of self-priming pump 1)Drain screw cock 2)Connector of inlet pipe 3)Tighten net of inlet pipe 4)Connector 5)Door valve 6)Screw cock of adding water 7)Elbow of outlet 8)Case of pump 9)Machinery seal...
-
Page 6: Analysis Of Malfunction And Remedy
6.When the pump is used in winter, to screw off the drain cock under the pump and draw off water thoroughly after stop the machine to prevent from being broken by ice of freeze. Ⅴ Ⅴ Ⅴ Ⅴ INSTALLATION OF CONNECTIVE SOFT PIPE Set the rubber soft pipe on the connector of inlet pipe. - Page 7 Listen to the sound carefully, There is a rub between impeller and flow whether the impeller is clashed with guidance. the case and then to adjust. The impeller is obstructed by weeds or Check and clean up. foreign matters. The connector of inlet pipe is loosed or Check inlet pipeline and remedy.
-
Page 8: Parts Drawing Of Self-Priming Pump
· · · · PARTS DRAWING OF SELF-PRIMING PUMP... - Page 9 PARTS DRAWING OF SELF-PRIMING HIGH-PRESSURE PUMP...
- Page 10 Ⅰ Ⅰ Ⅰ Ⅰ Detailed list of part for 2’’ self-priming pump Code Name Remarks screw GB3452.1-82 seal ring 35502500 GB5783-86 bolt M8×25 GB97.1-85 washer 8 case of water pump washer diversion device impeller machinery seal GB900-76 bolt M6×50 seal ring cover of water pump bolt M6×55 GB900-76...
- Page 11 Ⅱ Ⅱ Ⅱ Ⅱ Detailed list of part for 3’’ self-priming pump Code Name Remarks screw GB3452.1-82 seal ring 35502470 GB5783-86 bolt M10×25 GB97.1-85 washer 10 case of water pump gasket diversion device impeller machinery seal GB900-76 bolt M6×55 seal ring cover of water pump GB900-76 bolt M6...
- Page 12 Ⅲ Ⅲ Ⅲ Ⅲ Detailed list of part for 4’’ self-priming pump Code Name Remarks screw GB3452.1-82 seal ring 35502470 GB5783-86 bolt M10×25 GB97.1-85 washer 10 case of water pump gasket diversion device impeller machinery seal GB900-76 bolt M6×55 seal ring cover of water pump GB900-76 bolt M6...
- Page 13 Ⅳ Ⅳ Ⅳ Ⅳ Detailed list of part for 1.5” self-priming high-pressure pump Code Name Remarks GB5787-86 Screw M8×60 Plastic plug “O” rubber seal elbow Outlet cap connector gasket Outlet cap gasket gasket connector case of water pump Bottom valve Screw M4×12 GB5787-86 Screw M8×40...
- Page 14 Code Name Remarks “O” rubber seal Diffuser Axle Axle fence washer Mechanical seal “O” rubber seal Pump casing Diffuser Plastic bush Impeller...
Need help?
Do you have a question about the TI3 KGP80B and is the answer not in the manual?
Questions and answers