Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for Opal-RT OP5330
- Page 1 OP5330 USER GUIDE Digital to Analog Converter Module www.opal-rt.com...
- Page 2 Published by OPAL-RT Technologies, Inc. 1751 Richardson, suite 2525 Montréal (Québec) Canada H3K 1G6 www.opal-rt.com © 2014 OPAL-RT Technologies, Inc. All rights reserved Printed in Canada...
-
Page 3: Table Of Contents
DESCRIPTION ............................ 5 OFFSET AND GAIN CALIBRATION ........................5 MODULE INSTALLATION AND CONFIGURATION ................6 CIRCUIT LAYOUT DIAGRAMS ......................6 SCHEMATICS ............................7 OP5330 DB37F PIN ASSIGNMENTS ....................8 SPECIFICATIONS ........................... 9 TYPICAL APPLICATIONS ........................10 OPAL-RT Technologies OP5330 User Guide... -
Page 4: Getting Started
GETTING STARTED Features GETTING STARTED Before you begin, verify that your system meets the requirements of the OP5330 board: SOFTWARE REQUIREMENTS • RT-LAB 8.4.0 and higher • MATLAB 32 bits 6.5 and higher • Windows XP and higher HARDWARE REQUIREMENTS •... -
Page 5: Introduction
The OP5330 digital to analog converter (DAC) provides 16 single-ended digital output channels. Each channel uses a 16-bit resolution digital-to-analog converter. The OP5330 is a part of the OP5000 series of optional modules for OPAL-RT’s state of the art HIL (hardware-in-the-loop) systems, intended for use with OPAL-RT carrier boards (see “Hardware Requirements”... -
Page 6: Module Installation And Configuration
CIRCUIT LAYOUT DIAGRAMS When the OP5330 is installed on the carrier board, only the top of the circuit board is visible, as shown in Figure 1. The connectors are located on the bottom of the board (see Figure 2) and fit snugly into the connectors on the carrier. -
Page 7: Schematics
Schematics SCHEMATICS Figure 3 represents a simplified schematic of one channel of the OP5330 module. It is composed of three stages: the first stage consists of one gain DAC and one offset DAC; the second stage consists of a signal DAC with an operational amplifier that allows for gain adjustments; the third stage consists of an operational amplifier that receives final signal value and integrates the offset. -
Page 8: Op5330 Db37F Pin Assignments
Module Installation and configuration OP5330 DB37F Pin Assignments OP5330 DB37F PIN ASSIGNMENTS Connector P1 Ch. 0-15 OP5330 pin OP5330 pin DB37F DB37F assignment assignment +OUT00 -GND00 +OUT01 -GND01 +OUT02 -GND02 +OUT03 -GND03 +OUT04 -GND04 +OUT05 -GND05 +OUT06 -GND06 +OUT07 -GND07... -
Page 9: Specifications
Specifications OP5330 DB37F Pin Assignments SPECIFICATIONS Product Name: OP5330 Part Number: 126-0157 Number of channels: 16 single-ended Resolution: 16 bits Default range: ± 16 Volts Maximum current: 15 mA Max. Sampling Frequency: 1 MS/s Min Conversion / Acquisition Time: 1 μs per channel... -
Page 10: Typical Applications
Specifications Typical Applications TYPICAL APPLICATIONS The following diagrams provide an example of a typical application using the OP5330. OP5330 User Guide OPAL-RT Technologies... - Page 11 OPAL-RT Technologies OP5330 User Guide...
- Page 12 H3K 1G6 recently issued regulations, standards, and Tel.: 514-935-2323 guidelines. Toll free: 1-877-935-2323 This publication is not intended to form the basis of a contract. Technical Services www.opal-rt.com/support UG14-18121-OP1 05/2014 © OPAL-RT Technologies Inc.
Need help?
Do you have a question about the OP5330 and is the answer not in the manual?
Questions and answers