Related Manuals for Insignia NS-BK1TSS6
Summary of Contents for Insignia NS-BK1TSS6
- Page 1 USER GUIDE Single- and Dual-Tap Kegerator/Beverage Cooler NS-BK1TSS6/NS-BK2TSS6 Before using your new product, please read these instructions to prevent any damage.
-
Page 2: Table Of Contents
Specifications ...........25 ONE-YEAR LIMITED WARRANTY - INSIGNIA ..... . .27... -
Page 3: Introduction
Insignia Single- and Dual-Tap Kegerator/Beverage Cooler Introduction Congratulations on your purchase of a high-quality Insignia product. Your NS-BK1TSS6 or NS-BK2TSS6 represents the state of the art in kegerator/beverage cooler design and is designed for reliable and trouble-free performance. Important Safety Instructions... - Page 4 Insignia Single- and Dual-Tap Kegerator/Beverage Cooler 10 Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the appliance. 11 Do not attempt to modify or extend the power cord of this appliance.
-
Page 5: Grounding Requirement
Insignia Single- and Dual-Tap Kegerator/Beverage Cooler 2) Leave the shelves in place so that children may not easily climb inside 5 Unplug the kegerator/beverage cooler before performing user maintenance on it. 6 This kegerator/beverage cooler can be used by children age 8 years... -
Page 6: Features
Insignia Single- and Dual-Tap Kegerator/Beverage Cooler Features • 5.6 cu.ft • Dual taps for multiple kegs (dual-tap model only) • Convertible to refrigerator/beverage cooler • Stainless steel door • Adjustable thermostat for ideal temperature • Holds one 1/2 keg (pony keg) or 1/4 keg slim •... - Page 7 Insignia Single- and Dual-Tap Kegerator/Beverage Cooler Keg parts Beer tap handle Dual-tap beer Single-tap beer Single draft arm Dual draft arm (one for single-tap, gasket with gasket assembly (single-tap assembly (dual-tap two for dual tap. screws (4) model only) model only)
-
Page 8: Single-Tap Model
Insignia Single- and Dual-Tap Kegerator/Beverage Cooler Single-tap model Draft arm assembly Guardrail Thermostat (on the back of the unit) Drip tray Worktop tank tank regulator Keg coupler tank retainer Locking casters Beer keg www.insigniaproducts.com... -
Page 9: Dual-Tap Model
Insignia Single- and Dual-Tap Kegerator/Beverage Cooler Dual-tap model Draft arm assembly Guardrail Thermostat (on the back of the unit) Drip tray Worktop Keg couplers tank regulator tank tank retainer Locking casters Beer keg Locating your kegerator/beverage cooler Before using your kegerator/beverage cooler •... -
Page 10: Finding A Suitable Location
Insignia Single- and Dual-Tap Kegerator/Beverage Cooler Finding a suitable location • This kegerator/beverage cooler is designed to be free standing only, and should not be recessed or built-in. • Place your kegerator/beverage cooler on a floor that is strong enough to support the kegerator/beverage cooler when it is fully loaded. -
Page 11: Assembling Your Kegerator/Beverage Cooler
Insignia Single- and Dual-Tap Kegerator/Beverage Cooler Notes • The kegerator/beverage cooler should always be plugged into its own individual electrical outlet which has a voltage rating that matches the rating plate. • We strongly recommend that you do not use an extension cord. -
Page 12: Attaching The Guard Rail
Insignia Single- and Dual-Tap Kegerator/Beverage Cooler 6 Step on the front of the locking casters to lock the kegerator/beverage cooler into place or step on the back to unlock the kegerator/beverage cooler. Attaching the guard rail • Insert the guard rail into the holes on the top of the kegerator/beverage cooler. -
Page 13: Installing The Co2 Regulator And Tank
Insignia Single- and Dual-Tap Kegerator/Beverage Cooler d Attach the draft arm to the worktop with the four screws provided. Beer tap handle Silver snug ring Draft arm assembly Beer tube Wing nut 2 Attach the black plastic beer tap handle to the top of the faucet, tightening it by hand until it's tight. - Page 14 Insignia Single- and Dual-Tap Kegerator/Beverage Cooler 5. NEVER drop or throw a CO tank. 6. ALWAYS keep a CO tank away from heat. Store extra tanks in a cool place (preferably 70°F). Securely fasten with a chain in an upright position when storing.
- Page 15 Insignia Single- and Dual-Tap Kegerator/Beverage Cooler Tank valve Dual-tap model gauge regulator Regulator nut Gas line connector Hose clamp tank gas lines T-connector line Hose clamp Hose clamp Hose clamp Single-tap model: 1 Feed a hose clamp over the end of the CO gas line.
-
Page 16: Attach The Co2 Tank
Insignia Single- and Dual-Tap Kegerator/Beverage Cooler 6 Feed a hose clamp over the non-threaded ends of the other two CO gas lines. 7 Connect the gas lines to the ends of the T-connector, then tighten the hose clamps. Leave about ½ inch between the top of the clamp and the end of the hose. -
Page 17: Installing And Setting Up A Beer Keg
Insignia Single- and Dual-Tap Kegerator/Beverage Cooler Installing and setting up a beer keg This kegerator/beverage cooler accepts almost all brand name kegs, except for Coors kegs. Keg sizes that can be used in your kegerator/beverage cooler: Barrel Liters Gallons Ounces 12 oz. -
Page 18: Adjusting Co 2 Regulator
Insignia Single- and Dual-Tap Kegerator/Beverage Cooler 4 Repeat steps 1-3 if you have a second keg. 5 Pull the black handle on the keg coupler and press it downward until it locks into position. The keg is now tapped. Note If beer comes up through the top of the wing nut, remove the wing nut, reposition the washer, then reattach the wingnut. -
Page 19: Using Your Kegerator/Beverage Cooler
Insignia Single- and Dual-Tap Kegerator/Beverage Cooler Using your kegerator/beverage cooler Setting the temperature The temperature range of the thermostat goes from 32° F to 45° F (0° C to 7° C). The optimum temperature for serving draught beer is between 34° F - 38° F (1.1° C - 3.3° C). We suggest that you keep an accurate thermometer handy to help you to adjust the temperature setting to your needs. -
Page 20: Automatic Defrosting
Insignia Single- and Dual-Tap Kegerator/Beverage Cooler 4 Open faucet handle quickly and completely and fill the glass to 2/3 full. 5 Level the glass and finish topping it off by pouring into the center of the glass. 6 Fully close the tap when the draw is complete. -
Page 21: Cleaning Beer Components
Insignia Single- and Dual-Tap Kegerator/Beverage Cooler Cleaning the beer components To prevent a build-up of yeast and mold in the beer lines, and to prevent a bad taste, clean your beer components when you replace a keg. 1 Remove the keg coupler and thoroughly rinse it in warm water. -
Page 22: Storing Your Kegerator/Beverage Cooler
Insignia Single- and Dual-Tap Kegerator/Beverage Cooler Storing your kegerator/beverage cooler If you will be away from your kegerator/beverage cooler for more than three weeks. 1 Turn off the kegerator/beverage cooler and unplug it from the wall outlet. 2 Remove all kegs and beverages. -
Page 23: Troubleshooting - Beer Quality
Insignia Single- and Dual-Tap Kegerator/Beverage Cooler Troubleshooting - beer quality Problem Possible cause Possible solution Excess formation of Recent keg agitation. If the keg has recently been moved, let it stand a minimum of foam “head.” Beer is all two hours before tapping. -
Page 24: Troubleshooting - Cooler
Insignia Single- and Dual-Tap Kegerator/Beverage Cooler Problem Possible cause Possible solution Abnormal beer taste System requires cleaning. See “Maintaining your kegerator/beverage cooler.” and/or smell. System contamination. Check hoses for possible air leaks. The beer has exceeded its shelf Replace the beer keg with a fresh one. -
Page 25: Specifications
Insignia Single- and Dual-Tap Kegerator/Beverage Cooler Problem Possible cause Possible solution The cooler turns on and The room temperature is Make sure that the door was properly installed. off frequently hotter than normal. The door has been opened too Make sure that the door is closed properly. - Page 26 Insignia Single- and Dual-Tap Kegerator/Beverage Cooler www.insigniaproducts.com...
-
Page 27: One-Year Limited Warranty - Insignia
Products and parts replaced under this warranty become the property of Insignia and are not returned to you. If service of Products or parts are required after the Warranty Period expires, you must pay all labor and parts charges. This warranty lasts as long as you own your Insignia Product during the Warranty Period. - Page 28 FOR THE BREACH OF ANY EXPRESS OR IMPLIED WARRANTY ON THIS PRODUCT, INCLUDING, BUT NOT LIMITED TO, LOST DATA, LOSS OF USE OF YOUR PRODUCT, LOST BUSINESS OR LOST PROFITS. INSIGNIA PRODUCTS MAKES NO OTHER EXPRESS WARRANTIES WITH RESPECT TO THE PRODUCT, ALL EXPRESS AND...
- Page 29 1-877-467-4289 (U.S. and Canada) or 01-800-926-3000 (Mexico) INSIGNIA is a trademark of Best Buy and its affiliated companies. Distributed by Best Buy Purchasing, LLC V3 ENGLISH ©2015 Best Buy. All rights reserved. 15-1016 Made in China.