Edimax WAP1200 User Manual
  1. Manuals
  2. Brands
  3. Edimax Manuals
  4. Network Card
  5. WAP1200
  6. User manual
Edimax WAP1200 User Manual

Edimax WAP1200 User Manual

Wall mount access point
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
WAP1200
User Manual
07-2014 / v1.0

Advertisement

Table of Contents
loading

Related Manuals for Edimax WAP1200

Summary of Contents for Edimax WAP1200

  • Page 1 WAP1200 User Manual 07-2014 / v1.0...

  • Page 2: Table Of Contents

    CONTENTS I. Product Information ................1 I-1. Package Contents ......................1 I-2. System Requirements ....................1 I-3. Hardware Overview ....................... 2 I-4. LED Status ........................2 I-5. Reset ..........................2 I-6. Magnetic Wall Mount ....................3 I-7. Safety Information ......................4 II.
  • Page 3 IV-3-1-4. WDS ..........................37 IV-3-2. 5GHz 11ac 11an ......................39 IV-3-2-1. Basic ..........................39 IV-3-2-2. Advanced ........................41 IV-3-2-3. Security ........................43 IV-3-2-4. WDS ..........................45 IV-3-3. WPS ..........................47 IV-3-4. RADIUS ......................... 49 IV-3-4-1. RADIUS Settings ......................50 IV-3-4-2. Internal Server ......................

  • Page 4: Product Information

    I. Product Information I-1. Package Contents WAP1200 Access Point Quick Installation Guide Antennas x 2 Ethernet Cable Magnetic Wall Mount x 2 & Screws Power Adapter Magnetic Wall Mount Screw Template I-2. System Requirements - Existing cable/DSL modem & router...

  • Page 5: I-3. Hardware Overview

    I-3. Hardware Overview C LAN 2 D Reset A 12V DC IN B LAN 1 (PoE) 12V DC port to connect the power adapter LAN port with Power over Ethernet (PoE) IN LAN port with Power over Ethernet (PoE) OUT Reset the access point to factory default settings I-4.

  • Page 6: I-6. Magnetic Wall Mount

    Press the back of your access point firmly against the two wall mounted magnetic strips, with the access point’s Edimax logo in the correct, upright orientation as displayed above. Ensure your access point is securely attached to the magnetic...

  • Page 7: I-7. Safety Information

    I-7. Safety Information In order to ensure the safe operation of the device and its users, please read and act in accordance with the following safety instructions. 1. The access point is designed for indoor use only; do not place the access point outdoors.

  • Page 8: Ii. Quick Setup

    II. Quick Setup II-1. Initial Setup Connect the access point to a computer via Ethernet cable. Connect the power adapter to the access point’s 12V DC port and plug the power adapter into a power supply. Please wait a moment for the access point to start up. The access point is ready when the LED is blue.
  • Page 9 You will arrive the “System Information” screen shown below. Next, please follow the instructions below in II-2. Basic Settings to configure the access point’s basic settings.

  • Page 10: Ii-2. Basic Settings

    For more advanced configurations, please refer to IV. Browser Based Configuration Interface. II-2. Basic Settings The instructions below will help you to configure the following basic settings of the access point: - LAN IP Address - 2.4GHz & 5GHz SSID & Security - Administrator Name &...
  • Page 11 To change the SSID of your access point’s 2.4GHz wireless network(s), go to “Wireless Setting” > “2.4GHz 11bgn” > “Basic”. Enter the new SSID for your 2.4GHz wireless network in the “SSID1” field and click “Apply”. To utilize multiple 2.4GHz SSIDs, open the drop down menu labelled “Enable SSID number”...
  • Page 12 To change the administrator name and password for the browser based configuration interface, go to “Management” > “Admin”. Complete the “Administrator Name” and “Administrator Password” fields and click “Apply”. To set the correct time for your access point, go to “Management” > “Date and Time”.

  • Page 13: Ii-3. Wi-Fi Protected Setup (Wps)

    You can use the “Acquire Current Time from your PC” button if you wish to set the access point to the same time as your PC. The basic settings of your access point are now configured. Please refer to III. Hardware Installation for guidance on connecting your access point to a router or PoE switch.

  • Page 14: Iii. Hardware Installation

    III. Hardware Installation Connect a router or PoE switch to the access point’s LAN 1 port using an Ethernet cable. PoE switches must be connected to the access point’s LAN 1 port. If you are using a router, then connect the power adapter to the access point’s 12V DC port and plug the power adapter into a power supply.

  • Page 15: Iv. Browser Based Configuration Interface

    IV. Browser Based Configuration Interface The browser-based configuration interface enables you to configure the access point’s advanced features. The WAP1200 features a range of advanced functions such as MAC filtering, MAC RADIUS authentication, VLAN configurations, up to 32 SSIDs and many more. To access the browser based configuration interface: Connect a computer to your access point using an Ethernet cable.
  • Page 16 Click “Apply” to save changes and reload the access point, or “Cancel” to cancel changes. Please wait a few seconds for the access point to reload after you “Apply” changes, as shown below. Please refer to the following chapters for full descriptions of the browser based configuration interface features.

  • Page 17: Iv-1. Information

    IV-1. Information Screenshots displayed are examples. The information shown on your screen will vary depending on your configuration. IV-1-1. System Information The “System Information” page displays basic system information about the access point.
  • Page 19 System Model Displays the model number of the access point. Product Name Displays the product name for reference, which consists of “AP” plus the MAC address. Uptime Displays the total time since the device was turned on. Boot From Displays information for the booted hardware, booted from either USB or internal memory.
  • Page 20 Authentication Displays the authentication method for the Method specified SSID. See IV-3. Wireless Settings Encryption Type Displays the encryption type for the specified SSID. See IV-3. Wireless Settings VLAN ID Displays the VLAN ID for the specified SSID. See IV-2-3. VLAN Additional Displays the additional authentication type for Authentication...

  • Page 21: Iv-1-2. Wireless Clients

    IV-1-2. Wireless Clients The “Wireless Clients” page displays information about all wireless clients connected to the access point on the 2.4GHz or 5GHz frequency. Refresh time Auto Refresh Time Select a time interval for the client table list to automatically refresh. Manual Refresh Click refresh to manually refresh the client table.
  • Page 22 been connected to the access point. Idle Time Client idle time is the time for which the client has not transmitted any data packets i.e. is idle. Vendor The vendor of the client’s wireless adapter is displayed here.

  • Page 23: Iv-1-3. Wireless Monitor

    IV-1-3. Wireless Monitor Wireless Monitor is a tool built into the access point to scan and monitor the surrounding wireless environment. Select a frequency and click “Scan” to display a list of all SSIDs within range along with relevant details for each SSID. Wireless Monitor Site Survey Select which frequency (or both) to scan, and...
  • Page 24 SSID. Type Displays the 802.11 wireless networking standard(s) of the specified SSID. Vendor Displays the vendor of the wireless router/access point for the specified SSID.

  • Page 25: Iv-1-4. Log

    IV-1-4. The system log displays system operation information such as up time and connection processes. This information is useful for network administrators. When the log is full, old entries are overwritten. Save Click to save the log as a file on your local computer.
  • Page 26 The following information/events are recorded by the log:  USB Mount & unmount  Wireless Client Connected & disconnected Key exchange success & fail  Authentication Authentication fail or successful.  Association Success or fail  WPS M1 - M8 messages WPS success ...

  • Page 27: Iv-2. Network Settings

    IV-2. Network Settings Screenshots displayed are examples. The information shown on your screen will vary depending on your configuration. IV-2-1. LAN-Side IP Address The “LAN-side IP address” page allows you to configure your access point on your Local Area Network (LAN). You can enable the access point to dynamically receive an IP address from your router’s DHCP server or you can specify a static IP address for your access point, as well as configure DNS servers.
  • Page 28 Subnet Mask Specify a subnet mask. The default value is 255.255.255.0 Default Gateway For DHCP users, select “From DHCP” to get default gateway from your DHCP server or “User-Defined” to enter a gateway manually. For static IP users, the default value is blank. DHCP users can select to get DNS servers’...

  • Page 29: Iv-2-2. Lan Port

    IV-2-2. LAN Port The “LAN Port” page allows you to configure the settings for your access point’s two wired LAN (Ethernet) ports. Wired LAN Port Identifies LAN port 1 or 2. Enable Enable/disable specified LAN port. Speed & Duplex Select a speed & duplex type for specified LAN port, or use the “Auto”...
  • Page 30 VLAN Interface Wired LAN Identifies LAN port 1 or 2 and wireless SSIDs Port/Wireless (2.4GHz or 5GHz). VLAN Mode Select “Tagged Port” or “Untagged Port” for specified LAN interface. VLAN ID Set a VLAN ID for specified interface, if “Untagged Port” is selected. Management VLAN VLAN ID Specify the VLAN ID of the management VLAN.

  • Page 31: Iv-3. Wireless Settings

    IV-3. Wireless Settings Screenshots displayed are examples. The information shown on your screen will vary depending on your configuration. IV-3-1. 2.4GHz 11bgn The “2.4GHz 11bgn” menu allows you to view and configure information for your access point’s 2.4GHz wireless network across four categories: Basic, Advanced, Security and WDS.

  • Page 32: Iv-3-1-1. Basic

    IV-3-1-1. Basic The “Basic” screen displays basic settings for your access point’s 2.4GHz Wi-Fi network (s). Wireless Enable or disable the access point’s 2.4GHz wireless radio. When disabled, no 2.4GHz SSIDs will be active. Band Select the wireless standard used for the access point.
  • Page 33 VLAN ID Specify a VLAN ID for each SSID. Auto Channel Enable/disable auto channel selection. Auto channel selection will automatically set the wireless channel for the access point’s 2.4GHz frequency based on availability and potential interference. When disabled, select a channel manually as shown in the next table.

  • Page 34: Iv-3-1-2. Advanced

    IV-3-1-2. Advanced These settings are for experienced users only. Please do not change any of the values on this page unless you are already familiar with these functions. Changing these settings can adversely affect the performance of your access point. Contention Slot Select “Short”...
  • Page 35 802.11g Protection Enable/disable 802.11g protection, which increases reliability but reduces bandwidth (clients will send Request to Send (RTS) to access point, and access point will broadcast Clear to Send (CTS), before a packet is sent from client.) 802.11n Protection Enable/disable 802.11n protection, which increases reliability but reduces bandwidth (clients will send Request to Send (RTS) to access point, and access point will broadcast...

  • Page 36: Iv-3-1-3. Security

    IV-3-1-3. Security The access point provides various security options (wireless data encryption). When data is encrypted, information transmitted wirelessly cannot be read by anyone who does not know the correct encryption key. It’s essential to configure wireless security in order to prevent unauthorised access to your network.

  • Page 37: Iv-3-1-3-1. No Authentication

    Load Balancing Load balancing limits the number of wireless clients connected to an SSID. Set a load balancing value (maximum 50). Authentication Select an authentication method from the drop Method down menu and refer to the information below appropriate for your method. Additional Select an additional authentication method from Authentication...

  • Page 38: Iv-3-1-3-4. Wpa-Psk

    IV-3-1-3-4. WPA-PSK WPA-PSK is a secure wireless encryption type with strong data protection and user authentication, utilizing 128-bit encryption keys. WPA Type Select from WPA/WPA2 Mixed Mode-PSK, WPA2 or WPA only. WPA2 is safer than WPA only, but not supported by all wireless clients. Please make sure your wireless client supports your selection.
  • Page 39 MAC Filter & MAC-RADIUS Authentication Restrict wireless clients access using both of the above MAC filtering & RADIUS authentication methods. MAC-RADIUS Authentication Restrict wireless clients access based on MAC address via a RADIUS server, or password authentication via a RADIUS server. See IV-3-4.RADIUS to configure RADIUS servers.

  • Page 40: Iv-3-1-4. Wds

    IV-3-1-4. WDS Wireless Distribution System (WDS) can bridge/repeat access points together in an extended network. WDS settings can be configured as shown below. When using WDS, configure the IP address of each access point to be in the same subnet and ensure there is only one active DHCP server among connected access points, preferably on the WAN side.
  • Page 41 2.4GHz WDS Functionality Select “WDS with AP” to use WDS with access point or “WDS Dedicated Mode” to use WDS and also block communication with regular wireless clients. When WDS is used, each access point should be configured with corresponding MAC addresses, wireless channel and wireless encryption method.

  • Page 42: Iv-3-2. 5Ghz 11Ac 11An

    IV-3-2. 5GHz 11ac 11an The “5GHz 11ac 11an” menu allows you to view and configure information for your access point’s 5GHz wireless network across four categories: Basic, Advanced, Security and WDS. IV-3-2-1. Basic The “Basic” screen displays basic settings for your access point’s 5GHz Wi-Fi network (s).
  • Page 43 Enable SSID Number Select how many SSIDs to enable for the 5GHz frequency from the drop down menu. A maximum of 16 can be enabled. SSID# Enter the SSID name for the specified SSID (up to 16). The SSID can consist of any combination of up to 32 alphanumeric characters.

  • Page 44: Iv-3-2-2. Advanced

    IV-3-2-2. Advanced These settings are for experienced users only. Please do not change any of the values on this page unless you are already familiar with these functions. Changing these settings can adversely affect the performance of your access point. Guard Interval Set the guard interval.
  • Page 45 Tx Power Set the power output of the wireless radio. You may not require 100% output power. Setting a lower power output can enhance security since potentially malicious/unknown users in distant areas will not be able to access your signal. Beacon Interval Set the beacon interval of the wireless radio.

  • Page 46: Iv-3-2-3. Security

    IV-3-2-3. Security The access point provides various security options (wireless data encryption). When data is encrypted, information transmitted wirelessly cannot be read by anyone who does not know the correct encryption key. It’s essential to configure wireless security in order to prevent unauthorised access to your network.
  • Page 47 Wireless Client Enable or disable wireless client isolation. Isolation Wireless client isolation prevents clients connected to the access point from communicating with each other and improves security. Typically, this function is useful for corporate environments or public hot spots and can prevent brute force attacks on clients’ usernames and passwords.

  • Page 48: Iv-3-2-4. Wds

    IV-3-2-4. WDS Wireless Distribution System (WDS) can bridge/repeat access points together in an extended network. WDS settings can be configured as shown below. When using WDS, configure the IP address of each access point to be in the same subnet and ensure there is only one active DHCP server among connected access points, preferably on the WAN side.
  • Page 49 5GHz WDS Mode WDS Functionality Select “WDS with AP” to use WDS with access point or “WDS Dedicated Mode” to use WDS and also block communication with regular wireless clients. When WDS is used, each access point should be configured with corresponding MAC addresses, wireless channel and wireless encryption method.

  • Page 50: Iv-3-3. Wps

    IV-3-3. Wi-Fi Protected Setup is a simple way to establish connections between WPS compatible devices. WPS can be activated on compatible devices by pushing a WPS button on the device or from within the device’s firmware/configuration interface (known as PBC or “Push Button Configuration”). When WPS is activated in the correct manner and at the correct time for two compatible devices, they will automatically connect.
  • Page 51 Check/uncheck this box to enable/disable WPS functionality. WPS must be disabled when using MAC-RADIUS authentication (see IV-3-1-3-6 & IV-3-4). Product PIN Displays the WPS PIN code of the device, used for PIN code WPS. You will be required to enter this PIN code into another WPS device for PIN code WPS.

  • Page 52: Iv-3-4. Radius

    IV-3-4. RADIUS The RADIUS sub menu allows you to configure the access point’s RADIUS server settings, categorized into three submenus: RADIUS settings, Internal Server and RADIUS accounts. A RADIUS server provides user-based authentication to improve security and offer wireless client control – users can be authenticated before gaining access to a network.

  • Page 53: Iv-3-4-1. Radius Settings

    IV-3-4-1. RADIUS Settings Configure the RADIUS server settings for 2.4GHz & 5GHz. Each frequency can use an internal or external RADIUS server.
  • Page 54 RADIUS Type Select “Internal” to use the access point’s built-in RADIUS server or “external” to use an external RADIUS server. RADIUS Server Enter the RADIUS server host IP address. Authentication Set the UDP port used in the authentication Port protocol of the RADIUS server. Value must be between 1 –...

  • Page 55: Iv-3-4-2. Internal Server

    IV-3-4-2. Internal Server The access point features a built-in RADIUS server which can be configured as shown below used when “Internal” is selected for “RADIUS Type” in the “Wireless Settings”  “RADIUS”  “RADIUS Settings” menu. To use RADIUS servers, go to “Wireless Settings” “Security”...
  • Page 56 “MAC-RADIUS” password used in IV-3-1-3-6 or IV-3-2-3. Session Timeout Set a duration of session timeout in seconds between 0 – 86400. Termination Action Select a termination-action attribute: “Reauthentication” sends a RADIUS request to the access point, “Not-Reathentication” sends a default termination-action attribute to the access point, “Not-Send”...

  • Page 57: Iv-3-4-3. Radius Accounts

    IV-3-4-3. RADIUS Accounts The internal RADIUS server can authenticate up to 256 user accounts. The “RADIUS Accounts” page allows you to configure and manage users. User Name Enter the user names here, separated by commas.
  • Page 58 Click “Add” to add the user to the user registration list. Reset Clear text from the user name box. Select Check the box to select a user. User Name Displays the user name. Password Displays if specified user name has a password (configured) or not (not configured).

  • Page 59: Iv-3-5. Mac Filter

    IV-3-5. MAC Filter Mac filtering is a security feature that can help to prevent unauthorized users from connecting to your access point. This function allows you to define a list of network devices permitted to connect to the access point. Devices are each identified by their unique MAC address.
  • Page 60 ‘aa-bb-cc-12-34-56,aa-bb-cc-11-22-33’ Click “Add” to add the MAC address to the MAC address filtering table. Reset Clear all fields. MAC address entries will be listed in the “MAC Address Filtering Table”. Select an entry using the “Select” checkbox. Select Delete selected or all entries from the table. MAC Address The MAC address is listed here.

  • Page 61: Iv-3-6. Wmm

    IV-3-6. WMM Wi-Fi Multimedia (WMM) is a Wi-Fi Alliance interoperability certification based on the IEEE 802.11e standard, which provides Quality of Service (QoS) features to IEE 802.11 networks. WMM prioritizes traffic according to four categories: background, best effort, video and voice. Configuring WMM consists of adjusting parameters on queues for different categories of wireless traffic.
  • Page 62 is input to the initial random backoff wait time algorithm for retry of a data frame transmission. The backoff wait time will be generated between 0 and this value. If the frame is not sent, the random backoff value is doubled until the value reaches the number defined by CWMax (below).

  • Page 63: Iv-4. Management

    IV-4. Management Screenshots displayed are examples. The information shown on your screen will vary depending on your configuration. IV-4-1. Admin You can change the password used to login to the browser-based configuration interface here. It is advised to do so for security purposes. If you change the administrator password, please make a note of the new password.
  • Page 64 Account to Manage This Device Administrator Set the access point’s administrator name. Name This is used to log in to the browser based configuration interface and must be between 4-16 alphanumeric characters (case sensitive). Administrator Set the access point’s administrator password. Password This is used to log in to the browser based configuration interface and must be between...
  • Page 65 Management Check/uncheck the boxes to enable/disable Protocol specified management interfaces (see below). When SNMP is enabled, complete the SNMP fields below. SNMP Version Select SNMP version appropriate for your SNMP manager. SNMP Get Enter an SNMP Get Community name for Community verification with the SNMP manager for SNMP-GET requests.

  • Page 66: Iv-4-2. Date And Time

    IV-4-2. Date and Time You can configure the time zone settings of your access point here. The date and time of the device can be configured manually or can be synchronized with a time server. Date and Time Settings Local Time Set the access point’s date and time manually using the drop down menus.

  • Page 67: Iv-4-3. Syslog Server

    Update Interval Specify a frequency (in hours) for the access point to update/synchronize with the NTP server. Time Zone Time Zone Select the time zone of your country/ region. If your country/region is not listed, please select another country/region whose time zone is the same as yours.

  • Page 68: Iv-4-4. I'm Here

    IV-4-4. I’m Here The access point features a built-in buzzer which can sound on command using the “I’m Here” page. This is useful for network administrators and engineers working in complex network environments to locate the access point. The buzzer is loud! Duration of Sound Set the duration for which the buzzer will sound when the “Sound Buzzer”...

  • Page 69: Iv-5. Advanced

    IV-5. Advanced Screenshots displayed are examples. The information shown on your screen will vary depending on your configuration. IV-5-1. LED Settings The access point’s LEDs can be manually enabled or disabled according to your preference. Power LED Select on or off. Diag LED Select on or off.

  • Page 70: Iv-5-2. Update Firmware

    Updated firmware versions often offer increased performance and security, as well as bug fixes. You can download the latest firmware from the Edimax website. Do not switch off or disconnect the access point during a firmware upgrade, as this could damage the device.

  • Page 71: Iv-5-3. Save/Restore Settings

    IV-5-3. Save/Restore Settings The access point’s “Save/Restore Settings” page enables you to save/backup the access point’s current settings as a file to your local computer or a USB device attached to the access point, and restore the access point to previously saved settings.
  • Page 72 Restore Settings from PC Restore Settings Click the browse button to find a previously saved settings file on your computer, then click “Restore” to replace your current settings. If your settings file is encrypted with a password, check the “Open file with password”...

  • Page 73: Iv-5-4. Factory Default

    IV-5-4. Factory Default If the access point malfunctions or is not responding, then it is recommended that you reboot the device (see IV-5.5) or reset the device back to its factory default settings. You can reset the access point back to its default settings using this feature if the location of the access point is not convenient to access the reset button.

  • Page 74: Appendix

    V. Appendix V-1. Configuring your IP address The access point uses the default IP address 192.168.2.2. In order to access the browser based configuration interface, you need to modify the IP address of your computer to be in the same IP address subnet e.g. 192.168.2.x (x = 3 – 254).
  • Page 75 Select “Use the following IP address”, then input the following values: IP address: 192.168.2.10 Subnet Mask: 255.255.255.0 Click ‘OK’ when finished.

  • Page 76: V-1-2. Windows Vista

    V-1-2. Windows Vista Click the “Start” button (it should be located in the lower-left corner of your computer), then click “Control Panel”. Click “View Network Status and Tasks”, then click “Manage Network Connections”. Right-click “Local Area Network”, then select “Properties”. The “Local Area Connection Properties” window will then appear, select “Internet Protocol Version 4 (TCP / IPv4)”, and then click “Properties”.

  • Page 78: V-1-3. Windows 7

    V-1-3. Windows 7 Click the “Start” button (it should be located in the lower-left corner of your computer), then click “Control Panel”. Under “Network and Internet” click “View network status and tasks”.
  • Page 79 Click “Local Area Connection”. Click “Properties”.
  • Page 80 Select “Internet Protocol Version 4 (TCP/IPv4) and then click “Properties”. Select “Use the following IP address”, then input the following values: IP address: 192.168.2.10 Subnet Mask: 255.255.255.0 Click ‘OK’ when finished.

  • Page 81: V-1-4. Windows 8

    V-1-4. Windows 8 From the Windows 8 Start screen, you need to switch to desktop mode. Move your curser to the bottom left of the screen and click. In desktop mode, click the File Explorer icon in the bottom left of the screen, as shown below.
  • Page 82 Right click “Network” and then select “Properties”. In the window that opens, select “Change adapter settings” from the left side.
  • Page 83 Choose your connection and right click, then select “Properties”. Select “Internet Protocol Version 4 (TCP/IPv4) and then click “Properties”.
  • Page 84 Select “Use the following IP address”, then input the following values: IP address: 192.168.2.10 Subnet Mask: 255.255.255.0 Click ‘OK’ when finished.

  • Page 85: V-1-5. Mac

    V-1-5. Mac Have your Macintosh computer operate as usual, and click on “System Preferences” In System Preferences, click on “Network”. Click on “Ethernet” in the left panel.
  • Page 86 Open the drop-down menu labeled “Configure IPv4” and select “Manually”. Enter the IP address 192.168.2.10 and subnet mask 255.255.255.0. Click on “Apply” to save the changes.

  • Page 87: V-1-6. Glossary

    V-1-6. Glossary Default Gateway (Access point): Every non-access point IP device needs to configure a default gateway’s IP address. When the device sends out an IP packet, if the destination is not on the same network, the device has to send the packet to its default gateway, which will then send it out towards the destination.
  • Page 88 A network mask is also a 32-bit binary pattern, and consists of consecutive leading 1’s followed by consecutive trailing 0’s, such as 11111111.11111111.11111111.00000000. Therefore sometimes a network mask can also be described simply as “x” number of leading 1’s. When both are represented side by side in their binary forms, all bits in the IP address that correspond to 1’s in the network mask become part of the IP network address, and the remaining bits correspond to the host ID.
  • Page 89 Application Protocol Port Number Telnet SMTP POP3 H.323 1720 SNMP SNMP Trap HTTP PPTP 1723 PC Anywhere TCP 5631 PC Anywhere UDP 5632 Access point: An access point is an intelligent network device that forwards packets between different networks based on network layer address information such as IP addresses.
  • Page 90 COPYRIGHT Copyright  Edimax Technology Co., Ltd. all rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission from Edimax Technology Co., Ltd.

  • Page 91: Federal Communication Commission Interference Statement

    Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
  • Page 92 EU Declaration of Conformity English: This equipment is in compliance with the essential requirements and other relevant provisions of Directive 1995/5/EC, 2009/125/EC, 2006/95/EC, 2011/65/EC. Français: Cet équipement est conforme aux exigences essentielles et autres dispositions de la directive 1995/5/CE, 2009/125/CE, 2006/95/CE, 2011/65/CE. Čeština: Toto zařízení...

  • Page 93: Declaration Of Conformity

    Declaration of Conformity We, Edimax Technology Co., Ltd., declare under our sole responsibility, that the equipment described below complies with the requirements of the European R&TTE directives. Equipment: AC1200 Wall Mount Access Point Model No.: WAP1200 The following European standards for essential requirements have been followed:...
  • Page 94 Notice According to GNU General Public License Version 2 This product includes software that is subject to the GNU General Public License version 2. The program is free software and distributed without any warranty of the author. We offer, valid for at least three years, to give you, for a charge no more than the costs of physically performing source distribution, a complete machine-readable copy of the corresponding source code.
  • Page 95 intact all the notices that refer to this License and to the absence of any warranty; and give any other recipients of the Program a copy of this License along with the Program. You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee.
  • Page 96 6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license from the original licensor to copy, distribute or modify the Program subject to these terms and conditions. You may not impose any further restrictions on the recipients’...

Table of Contents